TPS70933QDBVRQ1
Product Specifications
TPS70933QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS70933QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS70933QDBVRQ1: automotive 2.7 V to 30 V input 150 mA LDO with 1 microamp quiescent current, 3.3 V fixed
TPS70933QDBVRQ1 is an AEC-Q100 grade 1 linear regulator with a 1 microamp quiescent current, reverse current protection and a 30 V input rating, built for a rail that has to survive an automotive bus and stay alive with the ignition off in a SOT-23 (DBV) body of 5 pins. It accepts 2.7 V to 30 V on the input, delivers 150 mA with a 200 mA peak, and holds 3.3 V with 2 percent accuracy over the full temperature range. Quiescent current is 1 microamp, shutdown current is 150 nanoamp, and the part includes thermal shutdown, current limit and reverse current protection.
Order code and package
| Order code read out | TPS709 33 Q DBV R Q1: regulator TPS709, 3.3 V fixed, Q automotive grade, five pin SOT-23, R large tape and reel, Q1 automotive prefix |
| Package | SOT-23 (DBV), 5 pins, 2.9 mm by 2.8 mm, part marking SLR on the 1.2 V row of the family |
| Carrier in the vendor addendum | 3000 pieces on a large reel for the DBV body; the same voltage in the six pin WSON body is a separate order code with a different reel |
| Moisture level | Level 1, 260 degrees peak reflow, unlimited floor life |
| Lead finish | Nickel palladium gold, quoted as NIPDAU, with NIPDAUAG on some rows of the addendum |
| Qualification | AEC-Q100 qualified, temperature grade 1 covering minus 40 to plus 125 degrees ambient, human body model level 2 and charged device model C4B |
| Absolute maximum | 30 V is the recommended maximum input, and the family is specified over the full automotive temperature range rather than a commercial window |
Electrical parameters that decide the application
| Input range | 2.7 V to 30 V, which covers a 12 V or 24 V vehicle bus with load dump margin handled by the front end protection rather than by this device |
| Output | 3.3 V fixed on this order code, from a family that covers 1.2 V to 6.5 V |
| Output current | 150 mA continuous with a 200 mA peak capability for a transient load |
| Accuracy | 2 percent over the full temperature range, quoted as a specification rather than a typical |
| Quiescent current | 1 microamp typical with no load, which is what keeps an always-on module from draining the battery over a parked week |
| Shutdown current | 150 nanoamp typical with the enable pin low |
| Reverse current protection | The pass device blocks current from the output back to the input when the output is held above the input, so a rail held up by another source does not discharge into the input |
| Protection | Current limit and thermal shutdown, both specified for the automotive grade rather than borrowed from the industrial device |
| Stability | Stable with a small ceramic output capacitor, and the data sheet gives the minimum value rather than an ESR window |
| Enable | An active high enable pin allows the regulator to be shut down by a microcontroller, which is how the 150 nanoamp state is reached |
| Thermal path | The five pin SOT-23 relies on the copper under the part, and at 30 V in and 3.3 V out the dissipation at 150 mA is significant enough that the input voltage should be dropped elsewhere when possible |
| Temperature grades | Grade 1 is the minus 40 to plus 125 degree ambient part; other grades in the family exist as separate order codes |
How the Q1 code differs from the industrial part
| TPS70933QDBVRQ1 | the part on this page, 3.3 V, five pin SOT-23, automotive grade 1, 3000 pieces on a reel |
| TPS70933DBVR | the industrial equivalent of the same voltage and body, without the automotive qualification and with a lower temperature ceiling |
| WSON body | the six pin WSON option, which is a separate order code and is chosen when the board needs a smaller footprint than the SOT-23 |
| Grade 1 | minus 40 to plus 125 degrees ambient, with the qualification data held in the automotive data sheet rather than inferred from the industrial part |
| Q suffix position | the Q sits between the voltage code and the package code, which is how the automotive and industrial codes are told apart at a glance on a bill of materials |
Points to check before this part goes on a BOM
The Q1 suffix is not a cosmetic difference. AEC-Q100 grade 1 covers minus 40 to plus 125 degrees ambient with the qualification testing and the production part approval process behind it, and the data sheet is a separate document with its own electrical tables. A bill of materials that carries the Q1 code cannot be substituted with the industrial part without a change note, and a quote that offers the industrial code against a Q1 request is the quickest way to lose the order.
A 30 V input rating is what makes this part useful on a vehicle bus. A 12 V system sees transients well above the battery voltage, and while the regulator is not a load dump protector, it can sit behind a front end clamp and survive the remaining excursion. On a 24 V system the margin is thinner, so the clamp has to be chosen with the 30 V rating in mind rather than the nominal bus.
The 1 microamp quiescent current and the 150 nanoamp shutdown current are the two numbers that decide whether a module can be left connected. A body control module that draws 1 mA in sleep flattens a 60 amp hour battery in about seven weeks; at 1 microamp the same battery lasts decades and the limit becomes the self discharge of the battery itself, which is the point at which the regulator stops being the constraint.
Reverse current protection matters more in a vehicle than on a bench. When the ignition is switched off and the module's output rail is held up by a second supply or by a large capacitor while the input collapses, a regulator without blocking conducts that stored energy back into the input and can hold the bus up or damage the upstream clamp. The blocking is always on in this part, so there is no pin to configure and no sequencing rule to remember.
The 150 mA rating with a 200 mA peak is a deliberate pairing. A CAN transceiver plus a microcontroller in a receive state draws well under 100 mA, but a transmit burst or a flash write can pull a short peak above the rating, and the peak figure is what allows the rail to ride through it without the output collapsing. A load that needs a sustained 200 mA is outside the rating and would need a switching regulator instead.
The thermal calculation is the one that surprises a customer moving from a 5 V to a 3.3 V rail on a 24 V bus. At 24 V in and 3.3 V out with 150 mA, the part dissipates about 3.1 W, which no SOT-23 can carry. The fix is either a pre regulator to drop the bus to 5 V or a switching converter, and it is worth raising at the quotation stage rather than after the first board comes back hot.
Where this order code fits
Feeds infotainment head units, body control modules, telematics boxes, sensor clusters and any automotive module that needs a 3.3 V rail at up to 150 mA from a 12 V or 24 V bus with a microamp sleep current. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Is this part automotive qualified? Yes. The Q1 code is AEC-Q100 grade 1, minus 40 to plus 125 degrees ambient, with human body model level 2 and charged device model C4B. It has its own automotive data sheet and cannot be substituted with the industrial code without a change note.
How much current can it deliver? 150 mA continuous with a 200 mA peak, so a microcontroller with a CAN transceiver and a short transmit burst is inside the rating while a sustained 200 mA load is not.
What is the sleep current? 1 microamp quiescent with no load and 150 nanoamp with the enable pin low, which is what allows a module to stay connected to the battery for years.
Does it block reverse current? Yes. The pass device blocks current from the output back to the input when the output is held above the input, with no pin to configure.
Can it run from a 24 V bus directly? Electrically the 30 V rating allows it, but the dissipation at 24 V in and 3.3 V out at 150 mA is about 3.1 W, which the SOT-23 cannot carry. A pre regulator or a switching converter is the right answer above a 12 V bus.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.