Contact Us

TPS70748PWP

Brand: Texas Instruments
Texas Instruments TPS70748PWP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS70748PWP — Power Management & Signal Chain | Superb Automation

TPS70748PWP

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS70748PWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS70748PWP dual regulator with power-up sequencing for a split supply

The TPS70748PWP is a dual output linear regulator in a 20 pin HTSSOP body, built for processors that need two rails in a defined order. Regulator 1 is set to 3.3 V and delivers up to 250 mA, regulator 2 is set to 1.5 V and delivers up to 125 mA, and the two have separate input pins so one can run from a 5 V rail and the other from the 3.3 V rail it produces. The part also carries an open drain power-on reset with a 120 ms delay, a power good output for regulator 1, two manual reset inputs and an undervoltage lockout, which is most of the supervisory chain a split supply board would otherwise build from three separate parts.

The sequencing is set by the SEQ pin. With SEQ pulled high or left open, output 2 comes up first and output 1 is held off until output 2 has reached regulation. With SEQ pulled low the order reverses. That single pin is what makes the part usable across processor families whose data sheets disagree about which rail has to lead.

Dropout is quoted at 83 mV typical, which is low for a 250 mA regulator and comes from a PMOS pass device rather than a bipolar one. The family is stable with 10 microfarad low ESR capacitors, so the output capacitors are ceramic rather than tantalum, and the accuracy is 2 percent over load and temperature.

Key parameters from the SLVS291D document

Outputs3.3 V at up to 250 mA and 1.5 V at up to 125 mA on this order code
InputsSeparate VIN1 and VIN2 pins, 7 V upper limit in the vendor table
SequencingSEQ pin selects which output leads, output 2 first when SEQ is high or open
Dropout83 mV typical on the pass device
Accuracy2 percent over load and temperature
ResetOpen drain power-on reset with a 120 ms delay
Power goodOpen drain output for regulator 1
Manual resetTwo inputs, active low, for a front panel or a debug header
Output capacitorsStable with 10 microfarad low ESR ceramic parts
PackagePWP 20 pin HTSSOP, tube of 70 or tape and reel of 2000
Order codeTPS70748PWP, active in the vendor addendum

Which order code carries which pair of rails

The family covers 3.3 V paired with 2.5 V, 1.8 V, 1.5 V and 1.2 V, plus a dual adjustable member. The voltage pair is not encoded in a way a buyer can read off the suffix, so the part number has to be matched against the table in the document rather than inferred from the digits. On this page the pair is 3.3 V and 1.5 V, and a board that was written around a 1.8 V core rail needs the TPS70751PWP instead, which is the same die with a different factory trim.

Because the two regulators share a die and a ground return, the current in regulator 2 flows through the same package as regulator 1. The 125 mA limit on the second output is a thermal limit as much as an electrical one, and it is the reason the part is specified with the two loads in mind rather than each on its own.

Where this part fits

Split supply processors, DSPs, small FPGAs, industrial controllers and instrumentation that needs a 3.3 V peripheral rail and a 1.5 V or 1.8 V core rail with a defined power-up order and a reset that holds until both are valid. It also suits a retrofit where a board already has a three part supervisory chain and the parts are being consolidated. Our notes on replacing an older dual regulator without changing the sequencing behaviour are filed under power management cross reference, and the incoming checks for a mixed tube and reel shipment are in incoming inspection plan.

What to check before a purchase order

Check the reset polarity and the delay against the processor data sheet before anything else. A 120 ms delay that is shorter than the processor's own power-on requirement will release the core while its supply is still rising, and the failure shows up as a random boot hang rather than as a supply fault. The two manual reset inputs are active low, so a board that drives them from a push button needs the pull up to be present on the board, not assumed inside the part.

Check the dissipation on the 3.3 V regulator at full load. A 250 mA load from a 5 V input into 3.3 V is 0.43 W in an HTSSOP body with a thermal pad, and the pad has to be soldered to a copper area that the vendor's thermal table assumes. A board that leaves the pad on a thin trace will run the part into thermal shutdown at a fraction of the rated current, and the symptom is a rail that sags after a few seconds of load rather than at switch on.

Check the tube option against the assembly route. The 70 piece tube is convenient for hand assembly and for a prototype run, while the 2000 piece reel is what a line needs. The two are the same die and the same body, so the choice is a handling question, not an electrical one.

Questions that come up on this part

Does the part sequence the rails if both enables arrive together? Yes. The SEQ pin decides the order and the internal control holds the second output off until the first is in regulation, so the sequence does not depend on how the enables are timed.

Can the 1.5 V output supply 125 mA indefinitely? Only if the thermal path supports the total dissipation of both regulators at once. The 125 mA figure is the electrical limit, and the package temperature is what decides whether the board can use it.