Contact Us

TPS70618DRVR

Brand: Texas Instruments
Texas Instruments TPS70618DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS70618DRVR — Power Management & Signal Chain | Superb Automation

TPS70618DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS70618DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS70618DRVR 1.8 V fixed regulator with 1 microamp quiescent current

The TPS70618DRVR is the 1.8 V fixed member of the TPS706 family, a 150 mA linear regulator that runs from 2.7 V to 6.5 V and draws 1 microamp of quiescent current. That current is the reason the family exists: a product that sits in standby for weeks with one rail always on cannot afford a regulator that draws 50 microamps, and at 1 microamp the regulator itself is no longer the largest drain on a coin cell or a small lithium pack. Shutdown current is 150 nA typical, and the enable pin is the only control the part carries.

The body is the DRV, a six pin WSON of 2 mm by 2 mm. The same die is available in the DBV five pin SOT-23, which is the body to pick when the board has room and the assembly line prefers a leaded package. Fixed outputs run from 1.2 V to 5 V, so a family review covers most of the low rails on one board from one document.

Two features separate this part from a plain low dropout regulator. The first is reverse current protection: when the output is held above the input, for example a charged rail on a board whose supply has been switched off, the part blocks current from flowing back into the source instead of discharging the rail through the pass device. The second is the way ground current behaves in dropout. Many regulators multiply their ground current several times over when the input falls close to the output, and this family uses a control loop that holds that increase down, which is what keeps a battery powered product efficient in the last part of its discharge curve.

Key parameters from the SBVS245A document

Input range2.7 V to 6.5 V
Output1.8 V fixed on this order code, 1.2 V to 5 V across the family
Output current150 mA rated, 200 mA peak
Quiescent current1 microamp typical
Shutdown current150 nA typical with the enable pin low
Dropout245 mV at 50 mA, specified only where the output is 2.8 V or above
Accuracy2 percent over temperature
ProtectionReverse current, current limit and thermal shutdown
PackagesDBV five pin SOT-23 and DRV six pin WSON, 2 mm by 2 mm
Order codeTPS70618DRVR, WSON body, active in the vendor addendum

What the dropout figure does and does not cover

The 245 mV dropout number is quoted at 50 mA and it carries a condition that buyers skip: the figure is only valid where the output is 2.8 V or above, because below that the minimum input voltage of the part, not the pass device, is what limits the headroom. On a 1.8 V output the usable input floor is 2.7 V, which leaves 0.9 V of headroom, far more than the pass device needs. That is comfortable for a 3.3 V rail feeding it and marginal for a 2.5 V rail, and it rules out running a 1.8 V rail from a two cell alkaline pack whose voltage falls to 2.4 V.

At 150 mA the dissipation is 0.45 W across a 3.3 V to 1.8 V drop. In the DRV body the thermal resistance to ambient is high enough that a 0.45 W load raises the junction well above the board temperature, so the copper under the part is part of the current rating, not a cosmetic detail. A board that expects 150 mA continuously from a 5 V source into a 1.8 V load is asking the part to burn 0.48 W in a 4 square millimetre package.

Where this part fits

Camera modules, wearables, solid state drives, set-top boxes, handheld instruments and any always-on rail that has to hold 1.8 V while the rest of the product sleeps. The reverse current protection makes it a good fit for a board with two possible sources, such as a battery and a USB port, where one source can be present while the other is not. Substitution notes for this family sit under power management cross reference, and the checks that catch a mixed reel of two body styles are in incoming inspection plan.

What to check before a purchase order

Check which body the order code actually names. The DRV suffix is the WSON and the DBV suffix is the SOT-23, and both bodies carry the same electrical table, so a line that was qualified on the leaded part cannot be swapped to the leadless one without a reflow profile check. The two bodies also differ in thermal resistance, which changes the current a board can draw in practice.

Check the output capacitor against the stability requirement rather than against the reference circuit of a different family. A 1 microamp part with a large ceramic output capacitor can ring at light load if the capacitor is outside the vendor's stable window, and the symptom appears only at the load currents where the part is most useful. For a rail that stays on through a long standby, also confirm the leakage of the load against the 1 microamp quiescent current, since a load that leaks 20 microamps makes the regulator choice irrelevant.

Questions that come up on this part

Is 200 mA a continuous rating? No. The continuous figure is 150 mA and 200 mA is the peak the part supports, so a load that needs 200 mA continuously belongs on a 250 mA or 300 mA part.

Can the enable pin be tied to the input? Yes, with the caveat that the part then has no way to be shut down, and the 150 nA shutdown figure becomes unreachable. On a battery product the enable pin is usually the one line that decides whether the rail costs 1 microamp or 150 nA.