TPS65720YFFR
Product Specifications
TPS65720YFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS65720YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS65720YFFR charger, converter and regulator in a 2 mm package
The TPS65720YFFR is a power management IC for a small battery product: a linear charger with power path management, one step down converter and one linear regulator in a 25 ball wafer level chip scale package of 2 mm by 2 mm. The power path is rated to 28 V, which is what a product needs when the charger input is a cheap adapter or a USB cable that can be plugged into the wrong supply.
The charger limits its input current at either 100 mA or 500 mA, selected by a pin, and charges at up to 300 mA. The step down converter delivers 200 mA on this member, while TPS657201, TPS657202 and TPS65721 deliver 400 mA from the same body, and efficiency reaches 92 per cent. The converter runs from 2.3 V and up, so it works from the battery node as well as from the system node.
The linear regulator delivers 200 mA over a 1.8 V to 5.6 V input, which means it can be fed from the converter output for a quiet analogue rail or from the system node for a rail that has to survive when the converter is off. A battery pack temperature input lets the charger stop when the cell is outside its window, and a GPIO pair carries the status to the host.
Key parameters from the SLVS979C document
| Power path | Rated to 28 V, with power path management between adapter and battery |
| Input current limit | 100 mA or 500 mA selected by a pin |
| Charge current | Up to 300 mA |
| Converter | 200 mA on the TPS65720, 400 mA on the TPS657201, TPS657202 and TPS65721 |
| Converter input | From 2.3 V, efficiency up to 92 per cent |
| Linear regulator | 200 mA, 1.8 V to 5.6 V input, usable from the converter or the system node |
| Battery safety | External pack temperature input with a window comparator |
| Control | GPIO register pair with a direction register for status and control |
| Package | YFF 25 ball WCSP of 2 mm by 2 mm, 3000 pieces on a large reel, moisture level 1 |
| Ambient range | Minus 40 to 85 degrees on the published rows |
The 200 mA and 400 mA members share one body
TPS65720YFFR and the other three codes sit in the same 25 ball package with the same reel and the same floor life, and they differ in the current the converter can deliver. That is worth knowing when a product is upgraded: the board does not change, only the code on the reel and the inductor, which has to be rechecked against the higher current limit.
The charger block is identical across the four, so a product that only needs more rail current does not have to requalify the battery path.
Where this part fits
Bluetooth headsets, wearable bands, small medical patches, portable sensors and any product with a single cell, a charger input and one or two low current rails. The sourcing notes for this class sit under power management cross reference and one stop BOM sourcing.
What to check before a purchase order
Check which of the four codes the board was released against. All four are active, all four are 3000 pieces on a large reel, and the marking is the only visible difference on the reel. A 200 mA part on a board that expects 400 mA passes a bench test at low load and fails at transmit.
Check the input current limit setting against the adapter. A 100 mA setting on a 500 mA capable adapter triples the charge time, and a 500 mA setting on a weak adapter can collapse the input and restart the charger in a loop. The incoming check for a chip scale part is in incoming inspection plan.
Questions that come up on this part
Does the charger work without a battery? The power path keeps the system alive from the adapter, so a product can run with the cell removed, within the current the path can deliver.
Is the 28 V rating a charging rating? No, it is the withstand of the power path, and the charger itself operates from the usual adapter window well below it.
One further point about the regulator. It can be fed from the converter output or from the system node, and the choice decides whether the rail survives when the converter is off. A rail that feeds a real time clock or a memory backup takes the system node; a rail that feeds an analogue front end takes the converter output, because that node is already filtered by the converter's own output capacitor and does not move when the battery voltage does.
The GPIO pair also carries the charger status to the host, so a product can show charging, complete and fault states without an analogue measurement of the battery node.