Contact Us

TPS65252RHDR

Brand: Texas Instruments
Texas Instruments TPS65252RHDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65252RHDR — Power Management & Signal Chain | Superb Automation

TPS65252RHDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65252RHDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65252RHDR: a 4.5 V to 16 V dual synchronous buck with a 1 A USB switch and a supply supervisor in a 5 mm by 5 mm body

TPS65252RHDR is a two channel step down converter that carries 3 A on one rail and 2 A on the other from a 12 V input, with the sequencing, the power good signalling and a USB port switch built into the same package in a VQFN body of 28 pins. The RHD body is 28 pins on a 5 mm by 5 mm pad, and the part is put together for the set top box and home gateway market, where a 12 V adapter feeds two digital rails and a front panel USB port from one package.

Order code and package

Catalogue stringTPS65252RHDR, the RHD body with the R reel letter
BodyVQFN, 28 pins, 5.00 mm by 5.00 mm, exposed pad
Reel3000 pieces on a large tape and reel, with the RHDT row on the same quantity and moisture level 3 at 260 C for 168 hours on the .A row
Finish and moistureNIPDAU plating, moisture level 3, 260 C, 168 hour floor life on the .A row, which is a floor life that expires and has to be tracked
Temperatureminus 40 to 85 C ambient, which is 40 C short of the junction range many catalogues quote
MarkingTPS and 65252
DocumentSLVSAM1C, revised December 2012
Sequencingeach buck has its own enable and its own soft start pin, so the order and the ramp rate are set outside the package

Electrical parameters that decide the application

Input range4.5 V to 16 V, which covers a 5 V, 9 V or 12 V adapter without a pre regulator
Output range0.8 V up to the input minus 1 V, set by an external divider from a 0.8 V reference
Current, buck 13.5 A peak and 3 A continuous
Current, buck 22.5 A peak and 2 A continuous
Switching frequency300 kHz to 2.2 MHz set by a single resistor on ROSC, with the two channels 180 degrees apart to spread the input ripple
Current limitadjustable per channel with a resistor on RLIM, with the buck 1 range reaching 5.2 A and buck 2 reaching 4.5 A at 12 V in and 500 kHz
Soft start5 uA of charging current into an external capacitor, so the ramp is set by the capacitor and not by a fixed timer
Reference0.8 V, with the soft start time computed from that reference and the 5 uA source
Power gooda 10 ms watchdog on each converter, so the soft start has to finish inside that window or the power good signal never releases
USB switch1 A rated, 100 mOhm on resistance typical, with a programmable limit of 0.68 A at a 154 kOhm resistor and 1.36 A at 76.8 kOhm
USB protectiona 130 C thermal trip on the switch alone, separate from the 160 C shutdown of the converters
Lockoutinput undervoltage at 4.22 V rising and 4.1 V falling, with 110 us of deglitch on both edges
Internal rails3.3 V and 6.25 V bias outputs, each able to source 10 mA for external use at 12 V in
Low power modean external signal drops the quiescent current from 10 mA to 0.5 mA with the converters still enabled and no load

The two channels, the USB port and the supervisor in one body

TPS65252RHDRthe 3000 piece large reel row, active
TPS65252RHDTthe small reel row, same body and same moisture level
TPS65251the relative with a different channel split, for a board that needs more on the second rail
TPS65250an earlier member of the family with a different USB arrangement
What the supervisor addsa power good and reset generator that holds the downstream processor in reset until both rails are inside their window
What the USB switch addsa current limited port that can be turned off independently of the two buck rails

Points to check before this part goes on a BOM

The 85 C ambient rating is the first thing to check against the application. Many catalogues quote 125 C for a converter of this class and this one does not, which is a function of a 5 mm by 5 mm body carrying two converters and a USB switch. A set top box with a closed lid and no airflow runs at 70 to 80 C internally, which leaves very little margin, so the thermal calculation has to be done at the enclosure temperature rather than at the room temperature.

Current limit is set by a resistor and not by a fixed internal number, which is unusual and useful. A 3 A rail with a fixed 5 A limit allows an inductor to saturate before the limit acts. With RLIM in place the limit can be set just above the load, and the inductor can be chosen for that limit rather than for a worst case that never happens. The register of published ranges stops at 5.2 A on buck 1 and 4.5 A on buck 2, and those are the ceilings of the adjustment rather than the guaranteed value.

The 180 degree phase relationship between the two channels is free ripple reduction. Both channels draw their current from the same input capacitor, and with the switches out of phase the input current pulses interleave, which halves the root mean square ripple current the capacitor has to absorb at the same total load. On a 12 V to 1.2 V and 3.3 V pair that can be the difference between two 22 uF ceramics and four.

Moisture level 3 with a 168 hour floor life is a production constraint. The part has to be mounted within a week of opening the reel or it has to be baked, and a contract builder that does not track floor life will find this out on a Monday morning. The plain RHD row and the .A row print different levels, so the receiving inspection should read the label rather than assume the family is uniform.

The USB switch is a separate function, not a port controller. It limits current to the resistor selected value and trips at 130 C, and it does not do enumeration, charging signatures or data line handling. That is fine for a downstream port that feeds a dongle and not fine for a port that has to charge a phone at 2 A with the right signature, which needs a dedicated part.

Two internal rails at 3.3 V and 6.25 V are exposed for external use at 10 mA each. That 3.3 V rail is what the enable pins are referenced to in the electrical table, and it is also a convenient supply for a housekeeping microcontroller. Taking more than 10 mA from it loads the internal bias and changes the behaviour of the converters, so the figure on the data sheet is a limit and not a suggestion.

Setting the frequency, the limit and the ramp

Three external components decide how the converter behaves and all three are resistors or capacitors rather than registers. ROSC sets the switching frequency between 300 kHz and 2.2 MHz, RLIMx sets the peak current limit on each channel, and the capacitor on SSx sets the ramp from a 5 uA source into a 0.8 V reference. A 10 nF capacitor on SS1 gives a ramp of about 1.6 ms, which is short enough to finish inside the 10 ms power good watchdog.

The order of the calculations matters. Frequency first, because it sets the inductor and the ripple. Then the current limit, because it has to sit above the peak inductor current at full load and below the saturation point of the inductor that was chosen. Then the ramp, because it has to be long enough to keep the inrush inside the current limit and short enough to release the power good inside its watchdog. Doing them in the other order produces a board that either trips at start up or fails the timing.

What the supervisor actually watches

The power good comparator on each channel has a 10 ms watchdog, and the reset generator holds the downstream device until both rails report good. The watchdog is a timeout rather than a window, so a rail that rises too slowly never reports good and the processor stays in reset, which looks like a dead board rather than a timing problem. When a first article will not boot, the soft start capacitor is the first thing to measure.

The output voltage window that counts as good is set by the internal divider against the 0.8 V reference and is not adjustable. That is adequate for a digital rail and not adequate for a rail that has to be inside 2 per cent before a memory device is released. Where the downstream device is strict, the power good pin should drive an external supervisor with its own threshold rather than the internal one.

Where this order code fits

This is the main rail pair in a set top box, a DSL or cable modem, a home gateway, a wireless router or a car DVD player, where a 12 V adapter has to produce a core rail and an input output rail plus a front panel USB port Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can both channels run at full current at the same time? The channels are independent and both can be at their continuous rating, 3 A and 2 A, provided the thermal calculation allows it. The 28 pin body at 85 C ambient is the constraint, not the current rating.

How is the current limit set? With a resistor on each RLIMx pin. The published adjustment reaches 5.2 A on buck 1 and 4.5 A on buck 2 at 12 V in and 500 kHz, and the resistor should be chosen against the peak inductor current rather than the average load.

Is the USB switch a charging controller? No. It is a current limited switch with a 1 A rating, a 100 mOhm on resistance and a 130 C thermal trip. Charging signatures and enumeration are outside its function.

What is the ambient limit? 85 C, which is lower than most converters of this class. The junction range in the body of the document is wider, but the addendum rows are quoted at minus 40 to 85 C ambient.

Do I need an external supervisor? Only if the downstream device needs a tighter power good window than the internal comparator gives. The internal one is referenced to the 0.8 V divider and is not adjustable.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.