Contact Us

TPS65251RHAR

Brand: Texas Instruments
Texas Instruments TPS65251RHAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65251RHAR — Power Management & Signal Chain | Superb Automation

TPS65251RHAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65251RHAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65251RHAR three buck converters from a 4.5 V to 18 V bus

The TPS65251RHAR is the base member of the TPS65251 family: three synchronous step down converters with integrated power transistors, a 4.5 V to 18 V input and continuous output currents of 3 A on the first converter and 2 A on the other two, with maximum currents of 3.5 A and 2.5 A. The output range is 0.8 V to close to the input, set by an external divider against a 0.8 V reference quoted at 1 per cent. The body is a 40 pin VQFN of 6 mm by 6 mm rated minus 40 to 125 degrees junction.

What separates this member from the -1, -2 and -3 options is the low power input pin, which the plain part exposes so the host can force the converters into a light load behaviour instead of letting each one decide on its own. Everything else is shared: a per converter enable pin, a per converter soft start capacitor, a per converter current limit resistor, a synchronisation input and an oscillator set by a resistor between 300 kHz and 2.2 MHz.

Converter one runs 180 degrees out of phase with converters two and three, and the last two run in phase with each other. That arrangement halves the ripple current that the input capacitor sees compared with three converters switching together, which is the difference between a 10 microfarad ceramic bank and a much larger one on a 12 V bus.

Key parameters from the SLVSAA4G document

Input range4.5 V to 18 V operating, suited to 5 V, 9 V, 12 V and 15 V systems
Output range0.8 V to near the input voltage, external divider on each feedback pin
Reference0.8 V with 1 per cent accuracy
Output current3 A, 2 A and 2 A continuous, 3.5 A, 2.5 A and 2.5 A maximum
Switching frequency300 kHz to 2.2 MHz by resistor, or an external clock on the SYNC pin
Phase relationshipConverter 1 against converters 2 and 3, 180 degrees apart
Current limitAdjustable per converter through the RLIMx pins
Light loadLOW_P input selects the low power behaviour for the group
SupervisionPower good after the sequence, all internal flags and the reset delay
PackageRHA 40 pin VQFN of 6 mm by 6 mm, 2500 pieces on a large reel, moisture level 3

The four codes in the family are not interchangeable

The same 40 pin body and the same 2500 piece reel appear against TPS65251, TPS65251-1, TPS65251-2 and TPS65251-3. The suffix selects a factory option inside the part, and the vendor prints the four strings in one addendum table without decoding the option in words. A purchasing line that treats the suffix as a packaging letter will buy the wrong behaviour and see it only on a sequence test.

The practical rule is to keep the suffix with the product record, quote it in full on the purchase order, and check the marking against the drawing rather than against the family name. Our desk keeps the substitution notes for this family under power management cross reference.

Where this part fits

Industrial controllers, network appliances, set top boxes and boards that take a 12 V or 15 V input and need three rails with independent sequencing. The replacement route for a long lead time on this family is described under component lead time solutions.

What to check before a purchase order

Check the current limit resistors against the inductors. The limit is a peak current, so a converter set for 3.5 A with a 3 A rated inductor will saturate before the limit acts, and the failure appears as a shorted switch rather than as a clean fold back. The vendor gives the equation for the resistor, and the inductor saturation current has to sit above the resulting peak.

Check the soft start capacitors against the sequencing requirement. Three rails rising at once from one 12 V supply can pull the input below the lockout of the first converter, which restarts the sequence in a loop. The receipt check for the reel and the marking is in incoming inspection plan.

Questions that come up on this part

Can the three converters run from different inputs? Each has its own input pin, so a 12 V and a 5 V source can feed different converters, but the reference and the control circuit come from one of them.

Is the 0.8 V reference the lowest output? Yes, without an external reference or a negative rail injection, because the divider only scales up from the reference.

One further consideration applies to the 4.5 V floor. A 5 V bus with 10 per cent of tolerance sits at 4.5 V at the bottom, which is exactly the minimum input, and the converter needs headroom above its own drop to regulate a 3.3 V rail at full current. A 5 V bus that sags under load is therefore a marginal case for this family, and a 12 V bus removes the question entirely.