TPS65131WTRGERQ1
Product Specifications
TPS65131WTRGERQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS65131WTRGERQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS65131WTRGERQ1 automotive dual output converter for plus and minus rails
The TPS65131WTRGERQ1 generates a positive rail up to 15 V and a negative rail down to minus 15 V from a 2.7 V to 5.5 V input, with about 200 mA on each output depending on the input to output ratio. It is the automotive qualified member of the TPS65131 pair, tested to AEC Q100 grade 2 for a minus 40 to 105 degree ambient range with the electrical tables specified over minus 40 to 125 degrees junction. The body is a 24 pin VQFN of 4 mm by 4 mm with a thermal pad, and the W in the order code marks the wettable flank version.
Two things make this part useful in a display or a sensor bias chain. The first is the pair of independent enable pins, ENP and ENN, which let the positive rail come up before the negative one and go down after it, which is the order most panels and many analogue front ends require. The second is the control output for an external PFET, which isolates the load completely in shutdown instead of leaving it tied to the input through a body diode.
Efficiency is quoted up to 91 per cent on the positive rail and up to 85 per cent on the negative rail, with 85 per cent overall. Quiescent current in operation is 500 microamps and shutdown current is 0.2 microamps, so the part can stay connected to a permanent battery node.
Key parameters from the SLVSBB2F document
| Input range | 2.7 V to 5.5 V at VIN and INN, 6 V absolute maximum |
| Output range | Positive up to 15 V, negative down to minus 15 V, both adjustable |
| Output current | 200 mA typical on each rail, limited by the input to output ratio |
| Switch current limit | 2 A typical on both main switches, inverter window 1.7 A to 1.95 A at 3.6 V |
| Switch resistance | 440 to 620 milliohm on the inverter at 3.6 V, 330 milliohm at 5 V |
| Switching frequency | Fixed frequency PWM, 1.25 MHz minimum, power save mode at light load |
| Quiescent current | 500 microamps typical in operation, 0.2 microamps in shutdown |
| Protection | Current limit, overvoltage on both outputs, undervoltage lockout, thermal shutdown |
| Qualification | AEC Q100 grade 2, minus 40 to 105 degrees ambient, HBM H1C and CDM C4B |
| Package | RGE 24 pin VQFN of 4 mm by 4 mm with thermal pad, wettable flanks |
Why the wettable flank matters here
An automotive assembly line inspects solder joints on the side of the package, and a plain QFN does not show a fillet there. The W version has a plated step on the flank so the joint is visible to the automated optical check without an X ray step. That is a mechanical difference rather than an electrical one, and the die inside behaves the same.
The practical consequence is on the order: the same 24 pin body is published twice, once as TPS65131TRGERQ1 and once as TPS65131WTRGERQ1, both at 3000 pieces on a large reel, and the two rows carry different moisture levels, with the plain row at level 3 and a 168 hour floor life and the W row at level 1 with unlimited floor life. A module line that wants to skip the bake step has a reason to specify the W part even when the inspection plan does not require it.
Where this part fits
Small and medium OLED displays, thin film transistor liquid crystal panels, charge coupled device bias supplies, and automotive camera or cluster modules that need plus and minus rails from a single 3.3 V or 5 V feed. Related sourcing notes are filed under power management cross reference and component lead time solutions.
What to check before a purchase order
Check the W. The catalogue string on this page carries it, and dropping it buys the same die in a body whose joints cannot be inspected from the side. Check the negative rail load as well: the 200 mA figure is quoted for a specific input to output ratio, and an inverter running from 3.3 V to minus 15 V moves a large current through the switch, so the deliverable current falls well before the switch limit is reached.
Check the two enable pins against the panel sequence. Driving both from one GPIO defeats the purpose of the part, and a panel that sees the negative rail before the positive one can latch its gate driver. The incoming check for the reel and the floor life is in incoming inspection plan.
Questions that come up on this part
Can the outputs be set to different magnitudes? Yes, each rail has its own feedback divider, so a plus 8 V and a minus 6 V pair is a normal configuration.
Is the 2 A switch limit available at both rails? It is a peak switch limit, not an output current, and the average output current is set by the ratio of input to output voltage, so at a large step up ratio the useful output current is a small fraction of it.