TPS63900DSKR
Product Specifications
TPS63900DSKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS63900DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS63900DSKR: buck-boost converter with 75 nA of quiescent current and a 1.8 V to 5.5 V input
TPS63900DSKR is a single mode buck-boost converter in the ten pin DSK body that accepts 1.8 V to 5.5 V, produces 1.8 V to 5 V in 100 mV steps, holds 75 nA of quiescent current and 60 nA in shutdown, and delivers more than 400 mA from a 2 V input in a WSON body of 10 pins. The TPS63900 converts an input anywhere from 1.8 V to 5.5 V to an output between 1.8 V and 5 V without changing mode between buck, buck-boost and boost. Output is set by two external resistors in 100 mV steps, a select pin toggles between two presets, and the input current limit is programmable. The quiescent current is 75 nA and the shutdown current is 60 nA, which is what makes a single lithium cell or a pair of alkaline cells a viable supply for a decade of standby.
Order code and package
| Order code | TPS63900DSKR |
| Input voltage | 1.8 V to 5.5 V |
| Output voltage | 1.8 V to 5 V in 100 mV steps |
| Output setting | two external resistors, plus a select pin for a second preset |
| Output current | more than 400 mA at a 2 V input and a 3.3 V output |
| Peak switch current limit | 1.45 A typical |
| Quiescent current | 75 nA |
| Shutdown current | 60 nA |
| Efficiency at 10 uA | above 90 percent |
| Package | ten pin WSON, 2.5 mm by 2.5 mm, 0.5 mm pitch |
| Document | TPS63900 data sheet |
Electrical parameters that decide the application
| Modes | single mode across buck, buck-boost and boost |
| Junction to case bottom resistance | 10.0 C per W |
| Junction to board characterization parameter | 31.0 C per W |
| Stacking | multiple devices in parallel for higher output current |
| Input current limit | programmable |
| Dynamic voltage scaling | supported through the select pin |
| Quiescent current over a year | 0.66 mAh |
| Shutdown current over a year | 0.53 mAh |
Points to check before this part goes on a BOM
Seventy five nanoamps is 0.66 mAh over a year, which is smaller than the self discharge of most cells. That is the figure that makes a ten year shelf life possible: a 220 mAh coin cell would take three centuries to be emptied by the converter alone, so the standby budget belongs to the sensor and the leakage around it rather than to the regulator. The comparison only holds while the load is off, which is why the shutdown current of 60 nA and the way the enable pin is driven matter as much as the quiescent figure.
Single mode operation is the feature that removes a class of problems. A converter that switches between buck, buck-boost and boost as the cell voltage crosses the output has a transition region where the loop gain and the ripple both change, and a load step in that region can produce a disturbance that a downstream circuit notices. This part holds one control behaviour across the whole input range, so the output ripple and the transient response do not depend on where the cell happens to be in its discharge curve.
The 1.8 V input floor is what makes two alkaline cells usable to the end of their life, and the 5.5 V ceiling covers a USB rail and a single lithium cell at full charge. The interesting case is a 3.0 V rail from a cell that starts at 3.2 V: the converter bucks at the start and boosts at the end, and the input current rises as the cell voltage falls. At 400 mA out and 2 V in, the input current is over 700 mA before efficiency, which is the point at which the cell internal resistance becomes part of the regulation.
The programmable input current limit protects a coin cell or a thin film cell from being pulled below its cut off. A cell with 30 ohm of internal resistance delivering 700 mA would drop 21 V, which is impossible, so the limit is what tells the converter to reduce the load rather than collapse the rail. That behaviour has to be planned with the load in mind: a radio that transmits in bursts will hit the limit during the burst and the rail will sag, which is why the output capacitance is sized for the burst rather than for the average.
Stacking devices in parallel is offered for higher output current, and it works because the outputs share the same regulation point. Two devices in parallel halve the switch current per device and spread the loss, which is the useful move when the 1.45 A peak switch limit is the constraint rather than the thermal one. The outputs must be tied together at the load, and the feedback divider is shared, so the two devices are not independent rails.
The WSON body has a junction to case bottom resistance of 10.0 C per W and a junction to board parameter of 31.0 C per W, and both are small because the currents are small. At 400 mA out and 3.3 V from a 2 V input the loss is tens of milliwatts, so the thermal side is trivial and the electrical side is everything: the inductor, the input capacitance and the feedback divider are where a 75 nA converter becomes a 10 uA one if they are chosen carelessly.
The output is set by two resistors in 100 mV steps, and the feedback network is the largest single leakage path at these currents. A 10 Mohm divider across a 3.3 V output draws 330 nA, which is four times the quiescent current of the converter and would dominate the standby budget. The data sheet gives resistor values in the megaohm range for this reason, and the leakage of the feedback pin and the contamination of the board then become the terms that decide whether the 75 nA is achieved in a product.
Where this order code fits
This order code belongs on battery powered sensors, electronic shelf labels, wearable and medical patches, meters with a ten year life and any product that has to run from a cell whose voltage crosses the output voltage during its life. It is chosen when the cell voltage starts above the rail, falls through it and ends below it, because a buck converter cannot follow that curve and a boost converter wastes the top half of it. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Can this run from a single alkaline cell? The input floor is 1.8 V, so a single alkaline cell that ends its life at 0.9 V is below it. A pair in series starts at 3.2 V and ends at 1.8 V, which is exactly the range this part covers, and that is the common arrangement. A single lithium cell from 4.2 V down to 3.0 V also fits and stays in the buck region for most of its life.
Why does the quiescent current matter more than the efficiency? At a 10 uA load the converter is already above 90 percent efficient, so the loss in conversion is small compared with the current the converter draws for itself. At 75 nA the self consumption is under one percent of a 10 uA load, while a converter with 1 uA would spend ten percent of the load on itself. Standby current, not peak efficiency, is what a battery product is bought for.
What happens when the cell voltage equals the output voltage? Nothing dramatic, and that is the point. A single mode converter passes through the buck-boost region without a change of control behaviour, so the output ripple and the loop response stay close to what they were on either side. A converter with distinct modes has a transition band where both the ripple and the transient response change, and a load step in that band is where the output disturbance appears.
How is a second output preset used? The select pin toggles between two voltages set by the divider network, so a system can run a radio at one voltage for a transmit burst and a sensor at a lower voltage between bursts, without a second converter. The transition is a change of the feedback target, so the output moves at the rate the loop and the output capacitance allow, which is a few hundred microseconds rather than instant.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.