Contact Us

TPS62841YBGR

Brand: Texas Instruments
Texas Instruments TPS62841YBGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62841YBGR — Power Management & Signal Chain | Superb Automation

TPS62841YBGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62841YBGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62841YBGR: 750 mA in a 0.97 mm by 1.47 mm body

TPS62841YBGR is the wafer level chip scale member of the TPS6284x family: six solder balls on a 0.97 mm by 1.47 mm die, 1.8 V to 6.5 V in, 750 mA out, and an output between 0.8 V and 1.55 V set by one resistor on the VSET ball. It is the smallest way to put a 750 mA step-down on a board with this family, and it is the member that gives up two pins to get there.

The six balls are GND, VOS, VIN, SW, EN and VSET. There is no MODE ball and no STOP ball. The data sheet states both omissions in plain words: the MODE function is not available in the YBG package, where the device transitions between power-save and PWM modes on its own, and the STOP pin is only present on the DLC package. For a board that needs either behaviour this is the wrong tail. For a board that wants a fixed rail in the smallest area and lets the converter decide its own mode, it is the right one.

Everything below is taken from SLVSEC6D, revised March 2020, and from the package option addendum. The YBG tail ships 3000 pieces on a large reel, marked 62841, level 1 at 260 degrees, rated minus 40 to 125 degrees junction.

What the order code sits on

Functionsynchronous step-down converter with integrated switches
Input range1.8 V to 6.5 V, 7 V absolute maximum
Output range0.8 V to 1.55 V in 50 mV steps
Output current750 mA
Quiescent current80 nA typical at 1.2 V out, 60 nA at 1.8 V out
Shutdown current25 nA typical
Switching frequency1.8 MHz nominal, DCS-Control
Mode controlnone, automatic PFM to PWM transition, no forced PWM
Stop functionnone in this body
Switch current limit1.2 A typical high side, 1.0 A typical low side
Switch resistance430 milliohm high side and 170 milliohm low side at 3.6 V in
Output discharge35 mA typical on VOS after disable
Enable pull-down200 k to 450 k internal, released after start-up
PackageWCSP-6, 0.97 mm by 1.47 mm, no thermal pad
Thermal resistance133.4 degrees per watt junction to ambient on the JEDEC board
Carrier3000 pieces on a large reel, marking 62841, Sn finish
Moisture levellevel 1 at 260 degrees, unlimited floor life

What you lose with six balls, and what you keep

What you keep is the whole power stage and the whole light load behaviour: the same 1.2 A switch limit, the same 80 nA no-load current, the same 25 nA shutdown, the same 1.8 MHz switching frequency and the same 100 percent duty cycle mode with 120 nA at dropout. The regulation loop is the same DCS-Control block, internally compensated, with the same external set of one inductor and two capacitors.

What you lose is control over the mode and the ability to silence the converter. Without MODE the part decides for itself: PFM at light load, PWM at heavy load, and the crossover happens where the loop says it should. That is the right behaviour for a battery node and the wrong behaviour for a radio that needs low ripple at 1 mA. Without STOP there is no way to freeze the switching for a measurement window, so a precision front end on this body has to either accept the switching spur or take its sample synchronously.

The third thing that changes is the thermal path. There is no pad and no lead frame to spread heat, so the 133.4 degrees per watt figure applies to a body whose only heat path is six balls. At 3.6 V in, 1.2 V out and 750 mA the converter loses roughly 0.16 W, which lifts the junction about 21 degrees. In still air at 25 degrees that is fine. At 60 degrees inside a sealed enclosure with the part surrounded by other loads, the same loss puts the junction near 81 degrees, and the derating decision has to be made before the board is released, not after.

Setting the rail and keeping the setting

The VSET resistor is read once at start-up and the readout block is switched off afterwards, so the resistor does not appear in the standby current. The window is the E96 value plus or minus about 5 percent, and the pin tolerates no more than 100 pF of parasitic capacitance to ground. On a chip scale body that limit is easy to break, because the ball is small, the trace to the resistor is short but the resistor itself often sits next to a ground pour on the same layer, and the pad capacitance plus the trace can approach the limit. The symptom of a false read is a rail one step away from the intended value, which is a fault that passes a quick power-up check and fails in the thermal chamber.

0.8 VVSET to GND, no resistor
0.85 V0.909 k
0.9 V1.74 k
0.95 V2.87 k
1.0 V4.32 k
1.05 V6.04 k
1.1 V8.45 k
1.15 V11.5 k
1.2 V15.8 k
1.25 V21.5 k
1.3 V28.7 k
1.4 V52.3 k
1.5 V102 k
1.55 V267 k
Inductor2.2 microhenry, effective 1.51 to 2.9 microhenry
Capacitors4.7 microfarad in, 10 microfarad out, both ceramic X5R or better

Where a product needs several rails, the same resistor chain can be built once and populated differently on two variants, because the converter reads the resistor rather than a stored value. That is the reason this family turns up in instruments with a 1.2 V and a 1.5 V variant of the same board, and it is also the reason a wrong resistor is the most common fault we see on incoming inspection of these boards.

Assembly notes for a chip scale body

A WCSP with six balls is not a hard part to place, but it is a part that punishes a stencil built for something else. The balls are small, the standoff is low, and the voiding that a coarse paste deposit leaves under the die shows up as a thermal problem rather than an electrical one, because the heat path is the balls. Our incoming inspection for this body checks the ball array under magnification and the paste deposit on the first article, and we keep the reflow profile inside the vendor window rather than at the top of the range.

The other assembly question is marking. The YBG tail is marked 62841, the DLC tail is marked E9 and the DGR tail is marked T841R. On a board with more than one member of the family, the marking is the only way to tell them apart after reflow, and a mixed reel is a defect that a functional test will not catch, because all three parts work at the same voltage.

For a customer moving a rail from an older 750 mA part into this body, the pin to pin cross reference sets out the ball map against the alternatives before a board revision is committed. For sensor patches and patient monitors, which are two of the applications the data sheet names, the medical device components page covers the traceability and lot control we hold on parts that go into a regulated product.

Questions we get on this part

Can the YBG body be used at 750 mA continuously? Yes, inside the thermal budget. The electrical rating is 750 mA and the junction to ambient figure is 133.4 degrees per watt, so the answer depends on the ambient and on the copper the six balls sit on, not on the current rating alone.

Why does this body have no MODE pin? The die has the function, the package does not bring it out. The data sheet says the device transitions between power-save and PWM modes automatically in this body, so the loop still does the right thing, the user just cannot force PWM.

Is the YBG a drop in replacement for the DLC? No. Different body, different ball count, different thermal path, and two functions missing. It is a functional equivalent in a smaller package, not a substitute on an existing land pattern.

What is the maximum input voltage in a transient? Seven volts absolute maximum on VIN, and the recommended operating range stops at 6.5 V. A two cell Li-Ion pack that charges to 8.4 V is outside both numbers, so a 5 V rail derived from it needs a front end converter before this part.

Does the part need an external discharge resistor? No. The VOS pin sinks about 35 mA typical when EN goes low, which pulls a 10 microfarad output down quickly enough for a restart test.