Contact Us

TPS62802YKAR

Brand: Texas Instruments
Texas Instruments TPS62802YKAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62802YKAR — Power Management & Signal Chain | Superb Automation

TPS62802YKAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62802YKAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62802YKAR: 1 A, 4 MHz step down converter with a resistor selected output in a 0.35 mm pitch chip scale body

TPS62802YKAR is a tiny synchronous buck that sets its output from one external resistor instead of a divider, so the same order code serves several rails in a WCSP body of 6 pins. It takes 1.75 V to 5.5 V in and delivers 1 A at any rail between 1.8 V and 3.3 V in 100 mV steps, selected by the resistor on the VSEL/MODE pin. Quiescent current is 2.3 uA typical, switching runs at 4 MHz, and the body is a 6 pin chip scale package on a 0.35 mm pitch.

Order code and package

TPS62802YKAR6 pin DSBGA (YKA), 0.35 mm pitch, 3000 pieces on a large reel
TPS62802YKATsame body, 250 pieces on a small reel
VSEL/MODE tied to groundfixed 1.8 V output, no resistor, no R2D conversion
Resistor on VSEL/MODEone of 16 internal settings between 1.8 V and 3.3 V in 100 mV steps
Shutdown current120 nA typical, 250 nA maximum with both enable and VSEL/MODE low

Electrical parameters that decide the application

Input voltage range1.75 V to 5.5 V, the whole range in one part number
Output current1 A continuous for this member, 0.6 A on the 06, 07 and 08 members
Output voltage1.8 V to 3.3 V, 16 internal steps of 100 mV, or a fixed 1.8 V with the pin grounded
Switching frequency4 MHz nominal, which is what allows the small inductor and the 0201 output capacitor
Quiescent current2.3 uA typical in power save mode
Output accuracy1 per cent over the full load and temperature range
High side current limit1.4 A minimum on this member, 1.3 to 1.55 A on the 00 and 01 members
Undervoltage lockout1.65 V falling typical, 1.75 V the guaranteed limit
Soft start125 us fixed ramp, no external capacitor
Thermal shutdown160 C typical with 20 C of hysteresis, not active in power save mode

How the six members of the family split

TPS628004 MHz, 1 A, 0.4 V to 0.775 V window, 25 mV steps, for core rails
TPS628014 MHz, 1 A, 0.8 V to 1.55 V window, 50 mV steps
TPS628024 MHz, 1 A, 1.8 V to 3.3 V window, 100 mV steps, the row on this page
TPS62806 to TPS62808the same three windows at 1.5 MHz and 0.6 A, for programs that cannot live with 4 MHz switching loss
Fixed output modeVSEL/MODE to ground gives one hard wired rail, the R2D converter is bypassed and accuracy is the internal trim
Forced PWM modea high level after start up keeps the converter switching at full frequency for the lowest ripple

Points to check before this part goes on a BOM

The reason to use this part is not the 1 A, it is the resistor. One order code covers sixteen rails, so a board that needs 1.8 V, 2.5 V and 3.3 V in three places stocks one part number and three resistors, and a rail change becomes a resistor change at the last minute. That is worth more than a few tenths of a percent of efficiency on a program with many low current rails.

The R2D converter reads the resistor once, at start up, and the vendor notes what happens if the read is disturbed by an undervoltage event: a false output voltage can be latched. On a supply that browns out slowly, the resistor node has to be clean at the moment the part leaves lockout, which in practice means keeping the resistor track short and away from the switch node.

A 4 MHz switching frequency is what makes a 0.35 mm pitch chip scale part usable, because the inductor can be 0.47 uH and the output capacitor 4.7 uF in an 0402 or 0201 body. It also means the switch node has to be treated as an RF node on the board. Radiated energy at 4 MHz and its harmonics is real, and a part this small is usually placed within a couple of millimetres of the load it feeds.

The 2.3 uA quiescent current only appears in power save mode, where the part skips cycles and runs from the output capacitor between bursts. Forced PWM holds the full 4 MHz and the current rises accordingly, which is the right choice for a rail that feeds an ADC or a radio and the wrong choice for a rail that sleeps. The VSEL/MODE pin carries both jobs, and the mode can be changed after start up by driving the pin high.

The current limit on this member is 1.4 A minimum against a 1 A rating, which is a smaller margin than the 1.3 A to 1.55 A window on the 00 and 01 parts. A 1 A load with a 1.4 A floor is comfortable, but a rail that has to charge a large capacitor at start up will sit in current limit for as long as it takes, and the 125 us soft start is the only thing that bounds the inrush.

The undervoltage lockout is the number that catches people on a 1.8 V rail. The part needs 1.75 V guaranteed to run and releases below 1.65 V, so a 1.8 V rail cannot feed a 1.8 V version of the same part, and a 2.5 V rail feeding a 1.8 V output sits only 700 mV above the lockout. The headroom table in the vendor document is worth reading before a cascade of rails is committed.

A chip scale body on a 0.35 mm pitch is not a part that can be hand reworked, and it is not a part that survives a reflow profile aimed at a larger package. The vendor quotes moisture level one unlimited floor life, which is helpful, but the solder paste volume on a 0.35 mm pitch land is the whole story at assembly. Programs that build this part need a stencil and a placement capability that matches the pitch, and a first article inspection on a sample of boards rather than one.

Sourcing this part is usually simple while it is on a published reel and awkward when a program needs a few hundred pieces for a pilot. The 250 piece small reel exists for exactly that case, and a broker offer that quotes only the 3000 piece large reel for a pilot is a sign the offer came from stock rather than from the vendor. The date code and the reel label are the two things to ask for on a part this small, because the marking is three characters and tells nobody anything.

Where this order code fits

This is the rail for a wearable or a module where the whole supply has to fit under 0.6 mm: sensor hubs, camera modules, Bluetooth and WiFi front ends, and the point of load rails around a small applications processor. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

How is the output voltage changed without changing the part number? Fit a different resistor on VSEL/MODE. The internal converter reads the resistor and selects one of sixteen settings, so the same reel serves every rail in the window.

Can the output be 1.2 V? Not with this member. The 1.8 V to 3.3 V window belongs to the TPS62802, the 0.8 V to 1.55 V window to the TPS62801 and the 0.4 V to 0.775 V window to the TPS62800.

Does it work from a single lithium cell? The input range starts at 1.75 V and the lockout sits at 1.75 V, so a cell that sags to 1.7 V under load is below the guaranteed start point. It is a 3.3 V and 5 V rail part, not a 1.8 V rail part.

What reel sizes are published? YKAR is 3000 pieces on a large reel and YKAT is 250 pieces on a small reel, both in the same 6 pin body and both active.

What happens if the resistor is missing? A missing resistor reads as the lowest setting in the window on this member, which is 1.8 V, the same rail as tying the pin to ground. It does not read as an open circuit fault.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.