TPS62162DSGR
Product Specifications
TPS62162DSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62162DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62162DSGR: 1 A step-down converter, 3 V to 17 V, fixed 3.3 V output
TPS62162DSGR is a fixed 3.3 V step-down converter rated 1 A from a 3 V to 17 V input in a WSON body of 8 pins. It is the 3.3 V member of the TPS6216x family, which switches at 2.25 MHz so a small inductor is enough, and it holds 17 microamp of quiescent current in power save mode with under 2 microamp in shutdown. The output is fixed, so there is no divider to add error, and the power good output lets the next rail wait for this one.
Order code and package
| TPS62162DSGR | Active, WSON-8, 3000 pieces on a large reel, MSL-2-260C-1 YEAR, minus 40 to 125 degrees |
| TPS62162DSGT | Active, the same body, 250 pieces on a small reel |
| TPS62160DSGR | Active, the adjustable member, same body and reel |
| TPS62161DSGR | Active, the fixed 1.8 V member |
| TPS62163DSGR | Active, the fixed 5.0 V member |
Electrical parameters that decide the application
| Input voltage | 3 V to 17 V |
| Continuous current | 1 A |
| Output | 3.3 V fixed on this string |
| Switching frequency | 2.25 MHz typical |
| Quiescent current | 17 microamp in power save mode |
| Shutdown current | under 2 microamp |
| Duty cycle | 100 per cent, the output follows the input at low headroom |
| Loop | DCS-Control, no external compensation |
Family variants and how they differ
| TPS62160 | adjustable from 0.9 V to 6 V |
| TPS62161 | fixed 1.8 V |
| TPS62162 | fixed 3.3 V, this order code |
| TPS62163 | fixed 5.0 V |
| Body options | WSON-8 at 2 mm by 2 mm and VSSOP-8 at 3 mm by 3 mm |
Points to check before this part goes on a BOM
The fixed output version is the accurate one. With no divider the output error is the reference error and the loop error, with no resistor tolerance on top. On a 3.3 V rail that is a meaningful gain for free, and it also removes two components and two places for a solder defect.
2.25 MHz is high enough that the inductor is small, and that is the point. At 1 A the inductor is a few microhenry, which fits under a connector on a dense board. The cost is switching loss, which shows up as lower efficiency at full load than a 500 kHz converter would give. The family is built for board area rather than for the last per cent of efficiency.
17 microamp in power save mode is a real figure for a battery rail. The converter stops switching and lets the output sag slowly, then bursts. That keeps the no load input current low, at the cost of a ripple that appears only at light load. A rail feeding an ADC has to be checked at low load, not only at full load.
100 per cent duty cycle is what lets the part work near the input voltage. A 3.6 V input with a 3.3 V output needs the switch to stay on almost continuously, and at the bottom of a battery discharge the part follows the input. That is a useful behaviour and it means the rail is not regulated in that condition.
DCS-Control is the reason there is no compensation network. The loop is built for ceramic capacitors and behaves like a hysteretic regulator at the transition, which gives a fast load response without an external network. The trade is that the output capacitor value matters more than on a voltage mode part: too little capacitance and the loop is unstable, too much and the transient is slow.
MSL-2 with a one year floor life applies to this body. That is a normal rating for a WSON and it means the reel can be open for up to a year before a bake. It is a better position than the level 3 parts in the same power family, and it matters for a assembly house holding stock between builds.
The power good output is open drain and needs a pull up. It goes to the logic rail of whatever reads it, and the value of the pull up sets the rise time. On a board that sequences three rails, this pin is the enable of the next converter, and the pull up is often the only component in that path.
1 A is a continuous rating with a thermal condition. The 2 mm body passes its loss into the pad. At a 17 V input and a 3.3 V output the duty cycle is short and the high side conducts briefly, so the loss is manageable. At a 17 V input and a 5 V output with a 1 A load the part runs hotter, and the pad and the copper area decide whether the rating can be used.
No divider means one less error term and one less placement. The fixed member is also the shortest bill of material, which matters on a rail that appears several times on one board. Four 3.3 V rails save eight components and eight solder joints by using the fixed member instead of four adjustable ones.
The output capacitor range is set by the loop, not by the transient. DCS-Control works with ceramic capacitors inside a range, and outside it the loop misbehaves. A larger part that looks better on paper can put the loop in the wrong place, so the recommended range is the reference and the transient is checked inside it.
17 V input and 1 A is a 12 V bus part. On a 12 V rail with a 3.3 V output the duty cycle is short and the loss is small. At 17 V the margin is thin, and a 24 V bus is outside the rating entirely, which is the first thing to check on a customer rail.
The power good pin is the sequencing hook. It is the only signal the part offers, and on a board that brings up three rails in order it is the cheapest way to do it. The open drain output needs one pull up, and the delay through that pull up is part of the sequence timing.
The 2 mm body and the 3 mm body are not interchangeable. Same silicon, different land pattern and different thermal path. A purchasing substitution between the WSON and the VSSOP member needs a board change, and the reel sizes differ as well.
Why the fixed 3.3 V member is the common choice
3.3 V is the rail most industrial and medical boards need, and the fixed version removes the divider, its tolerance and two placements.
The 17 V input covers a 12 V bus with margin for a transient, which is the usual source on those boards.
Where this order code fits
It makes a fixed 3.3 V rail at 1 A from a 12 V bus in industrial and medical equipment, with a power good output and a 17 V input ceiling. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Can the output be adjusted on this part? Not on this string. TPS62162 is the fixed 3.3 V member. The adjustable version is TPS62160, which shares the body and the pinout but needs a divider on the feedback pin.
Does it need an external compensation network? No. DCS-Control is internally compensated and expects ceramic output capacitors. The output capacitance still has to be chosen inside the range the loop supports.
What is the difference between the WSON and the VSSOP body? Size and thermal path, 2 mm by 2 mm against 3 mm by 3 mm. The silicon and the electrical behaviour are the same, but the land pattern differs, so it is a board change rather than a purchasing substitution.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.