Contact Us

TPS62150ARGTR

Brand: Texas Instruments
Texas Instruments TPS62150ARGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62150ARGTR — Power Management & Signal Chain | Superb Automation

TPS62150ARGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62150ARGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62150ARGTR: a 1 A step-down converter that takes 3 V to 17 V in, switches at 2.5 MHz in a 3 mm by 3 mm package and holds 17 uA of quiescent current with an adjustable soft start

TPS62150ARGTR is a synchronous converter with a hysteresis based control loop that reacts within a cycle, a power save mode that keeps efficiency at a milliamp, and a soft start pin that can also be used to track a second rail in a VQFN body of 16 pins. The RGT body is sixteen pins on a 3.00 mm by 3.00 mm pad, and the part exists because a 12 V rail has to come down to 3.3 V or 1.8 V in a space that has one inductor and one capacitor.

Order code and package

Catalogue stringTPS62150ARGTR, where 150 is the adjustable member, A is the variant that pulls the power good output low when the enable is low, and RGT is the sixteen pin VQFN
BodyVQFN, RGT, sixteen pins, 3.00 mm by 3.00 mm, with a thermal pad that must be soldered to the ground plane
Reel3000 pieces on a large tape and reel, with a 250 piece small reel on the T suffix
Finish and moistureNIPDAU plating, level 2 at 260 C, one year of floor life
Temperatureminus 40 to 125 C junction
MarkingPA8I on the body, the same marking across the family members
DocumentSLVSAL5E, November 2011, revised October 2021
StatusActive and in production on the addendum dated November 2025

Electrical parameters that decide the application

Input range3 V to 17 V, so a 5 V rail, a 12 V rail and a two cell battery all feed it, and a 15 V rail with 10 per cent of tolerance still fits
Output0.9 V to 6 V adjustable against an 800 mV reference, with a pin selectable 5 per cent offset on the fixed members
Current1 A continuous, with a high side forward limit of 1.4 to 2.2 A and a 1.7 A typical
Switching frequency2.5 MHz typical, or 1.25 MHz when the FSW pin is pulled high, with the change made by one pin rather than by a component
Quiescent current17 uA typical with the enable high and no load, and a shutdown current in the low microamp range with a 2.6 uA typical
On resistance90 mOhm typical and 170 mOhm maximum on the high side at 6 V or more of input, and 40 mOhm typical with 70 mOhm maximum on the low side
Lockout2.8 V falling with about 200 mV of hysteresis, which is under the 3 V operating floor and above a deeply discharged cell
Soft startan external capacitor charged with 2.3 to 2.7 uA, and the same pin accepts a tracking voltage so the rail can follow another
Power goodan open drain output that asserts above 92 to 98 per cent of the nominal output and releases at 87 to 94 per cent falling, with a 10 mA sink
Thermal shutdown160 C with 20 C of hysteresis, and 45 C per watt junction to ambient on a four layer board
Light loada power save mode that enters on its own and keeps efficiency at a milliamp, or forced PWM through the DEF pin on the fixed members
Protectionshort circuit protection by cycle by cycle current limit and an over temperature shutdown, with no external components

How the members of the family differ

TPS62150ARGTRadjustable, power good pulled low when the enable is low, 3000 pieces, marking PA8I, this page
TPS62150RGTthe plain adjustable member where the power good output is high impedance with the enable low, which changes how a supervisor reads the flag
TPS62151, TPS62152 and TPS62153fixed 1.8 V, 3.3 V and 5.0 V members in the same body, with the DEF pin adding 5 per cent to the nominal output
TPS62130 and TPS62140the same pin out at higher current, so a rail that grows from 1 A to 2 A or 3 A keeps the board arrangement
The TPS82150 modulethe same converter with the inductor inside, for a board that has no room to place and route an inductor
A linear regulatora 1 A linear part from 12 V to 3.3 V dissipates 8.7 W and needs a heatsink the size of the converter

Points to check before this part goes on a BOM

The A suffix is a small change with a real consequence. On this member the power good output is pulled low when the enable pin is low, so a supervisor that reads the flag sees a definite not ready rather than a floating pin. On the plain TPS62150 the flag goes high impedance with the enable low, and a supervisor with a pull up reads that as ready. A board that sequences three rails and reads three flags has to know which behaviour it has, and the letter in the order code is the only place that says.

The hysteresis loop reacts within a cycle and that is why there is no compensation network. The comparator watches the output and turns the high side on when the output falls below the threshold, so the response to a load step is immediate rather than filtered by an error amplifier. The price is that the switching frequency moves with the input and the load, and the 2.5 MHz figure is a typical rather than a fixed number. A rail that must avoid a particular band, an AM radio band for instance, needs the FSW pin and a check of the curve rather than a promise.

The soft start pin does two jobs and the second one is often missed. A capacitor sets the ramp, with 2.5 uA of source current into a 0.8 V reference, so 1 nF gives about 0.3 ms and 10 nF gives about 3 ms. The same pin accepts an analog voltage, which lets the rail track another rail rather than ramp on its own, and that is how a processor core and an input output rail are kept in order. A board that only needs a ramp still has to keep the pin inside its range, because a voltage above the reference holds the output off.

The 3 V input floor and the 2.8 V lockout are close together and that is deliberate. A lithium cell that is nearly empty sits at 3.1 V under load, and a converter that drops out at 3.0 V gives the system a few more minutes. The 200 mV of hysteresis stops the part from starting and stopping repeatedly at the end of discharge. A two cell pack at 6 V or a 12 V rail is far above both thresholds and the lockout never matters, which is why the same part number covers so many rails.

The 1.4 to 2.2 A current limit on a 1 A part is a wide window. The minimum is 40 per cent above the rating, so a load that draws 1.4 A does not trip every unit, and the maximum is more than twice the rating, so a short circuit can pull 2.2 A for the propagation delay of the comparator. The inductor has to hold its value at 2.2 A, not at 1 A, or the limit turns into saturation and the current rises further. That is the single most common way a 1 A rail fails a fault test.

The 17 uA quiescent current is measured in power save mode with the part not switching, so a rail that is loaded to a milliamp never sees it. The number that matters in a standby budget is the 17 uA plus the load, and on a 12 V input with a 3.3 V output the converter still runs its own bias from the input. A board that needs less than 5 uA total in standby cannot use this part at all, and the regulators built for that job hold under 1 uA.

Choosing the inductor for a 1 A rail

At 2.5 MHz with 12 V in and 3.3 V out, a 2.2 uH inductor carries 1.7 A of ripple, which is more than the load and clearly too much. The family is meant to run at 2.5 MHz with a 1 uH inductor for 3.3 V out, which gives 0.85 A of ripple, and at 2 A the peak sits at 2.4 A, above the minimum current limit. That is why a 1 A rail on 12 V in usually sets the FSW pin high for 1.25 MHz and uses a 2.2 uH inductor, which halves the ripple and stays inside the limit.

The output capacitor follows the ripple and the transient. A 22 uF ceramic holds about 15 mV of ripple at 0.85 A and 2.5 MHz, and a 1 A step with 30 mV of allowed droop needs about 15 uF of effective capacitance after the DC bias derating. A 22 uF part at 6.3 V in a 0805 body loses half its capacitance at 5 V of bias, so the effective value is the number that has to be used.

Using the soft start pin for tracking

Tracking means the output follows a voltage applied to the soft start pin rather than a capacitor. Two converters that track the same ramp reach their set points in the same order, and the difference between the rails stays inside the absolute maximum of whatever sits between them. A processor with a 3.3 V input output rail and a 1.2 V core rail usually wants the core to come up after the input output rail and to be down before it, and a tracking ramp is one way to guarantee that.

The pin is a current source into a capacitor, so a resistor to another rail works as a divider and a voltage above the 800 mV reference holds the output off. A board that drives the pin from a controller has to make sure the driving source cannot pull the pin below ground and cannot exceed the reference while the converter is meant to be running at full output.

Where this order code fits

This is the 12 V to 3.3 V or 12 V to 1.8 V stage in an industrial controller, a point of sales terminal, a solid state drive carrier, a server standby rail, a modem or a battery powered instrument, where a 1 A rail has to run from a wide input with one small inductor Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What does the A in the order code change? The power good output is pulled low when the enable pin is low, instead of going high impedance. It changes how a supervisor reads the flag during shutdown.

Can the switching frequency be changed? Yes. The FSW pin selects 2.5 MHz when low and about 1.25 MHz when high, with no component change.

Is the soft start adjustable? Yes. A capacitor on the SS/TR pin sets the ramp at 2.5 uA into an 800 mV reference, and the same pin can track another rail.

What is the input floor? 3 V of operating input, with a lockout that releases at about 2.8 V falling and 200 mV of hysteresis. A cell that sags below 3 V under load is at the limit.

Does it need a compensation network? No. The hysteresis loop has no external compensation and is stable into ceramic output capacitors without a network.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Safety Stock Planning page sets out the checks that keep a substitute from failing on the bench.