TPS61281DYFFR
Product Specifications
TPS61281DYFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61281DYFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61281DYFFR a battery front end that bypasses instead of boosting
The TPS61281DYFFR is a 16 bump chip scale part from the TPS6128xD family, a battery front end converter with a 2.3 V to 4.8 V input, a 2.3 MHz switching frequency, a 3 A valley inductor current limit and an integrated pass-through FET of 35 milliohm. It is the simple logic interface member of the family, with a GPIO pin configured as a reset and fault input output, and it covers single cell lithium, nickel rich, silicon anode and lithium iron phosphate chemistries.
The idea behind the part is that a battery spends most of its life above the voltage the load needs. In that state the converter closes a low resistance pass-through path and the load runs directly from the cell with 95 per cent efficiency and no switching loss. Only when the cell voltage falls below a threshold does the part start boosting, and it does that seamlessly, without a glitch at the output.
The threshold is selected by the VSEL pin: 3.15 V with VSEL low and 3.35 V with VSEL high. That single pin is the difference between a product that stays in pass-through longer and one that starts boosting earlier, which is a trade between efficiency and headroom for a following regulator.
Key parameters from the SLVSEA0B document
| Input range | 2.3 V to 4.8 V, with undervoltage lockout at 2.0 V to 2.1 V on a falling input |
| Output current | 4 A peak at a 3.35 V output from a 2.65 V input |
| Switching frequency | 2.3 MHz, with a 95 per cent efficiency figure at that frequency |
| Pass-through | 35 milliohm typical and 60 milliohm maximum on the bypass FET, 5 A current limit |
| Valley current limit | 2.475 A to 3.525 A around a 3 A typical, programmable through the interface |
| Quiescent current | 15.4 to 25.6 microamp in forced pass-through, 27.4 to 42.6 microamp in automatic mode |
| Shutdown | 3 to 6.6 microamp with the enable low, and the pass-through FET stays on for true bypass |
| Power good | Rising at 95 per cent and falling at 90 per cent of the output threshold |
| Package | 16 bump DSBGA, YFF body, 3000 pieces on a large reel, moisture level 1 |
True pass-through during shutdown
Most boost converters disconnect the load when they are disabled, or leak through a body diode. This part does the opposite on purpose: with the enable low it holds the pass-through FET on, so the load keeps running from the battery with only 3 to 6.6 microamp of overhead. A product that has to stay alive in a low power state, or that has to keep a real time clock and a memory rail biased, does not need a second path.
The catch is that the output is then the battery voltage, including its sag under load and its rise during charging. A downstream regulator has to accept that range, and a load that needs a stable rail has to be behind a regulator that can work from 2.3 V to 4.8 V. The part is a front end, not a regulated supply.
There is also a reverse leakage specification of 0.1 to 2 microamp into the switch node, which is the number that matters when the output is held by another source while the battery is removed. It is small enough that a service battery swap does not discharge the output rail through the converter.
The transition between modes is the hard part
The mode change happens when the input crosses the VSEL threshold. In boost mode the converter is regulating and the output is above the input; in pass-through the output follows the input minus the drop across the 35 milliohm FET. At the crossing, the loop has to hand over without a step at the output, and the part is specified for best in class line and load transient for that reason.
Two settings decide how the handover behaves: the valley current limit and the output voltage threshold, both programmable through the interface on the I2C members and set by pins on this logic interface member. A current limit that is too low makes the boost mode current limit before the battery is empty, which looks like an early shutdown rather than a mode change.
At 2.3 MHz the inductor is small, around 0.5 microhenry to 1 microhenry, and the whole solution fits in under 20 square millimetres at a sub 1 mm profile. That is the reason the part exists in a phone or a tablet, where the battery connector and the front end are the tallest things on the board.
Where this part fits
Single cell battery front ends in handsets, tablets, battery packs with silicon anode cells and any product that needs a 4 A peak boost plus a true bypass. Our desk keeps the cross reference for battery front end parts and the second source notes, see power management cross reference and one stop BOM sourcing.
What to check before a purchase order
Confirm the member, not only the body. The family has an I2C interface member and two logic interface members in the same 16 bump YFF body, with thresholds at 3.15 V and 3.35 V, and the only visible difference at goods inwards is the order code. A logic interface part on a board that expects I2C will regulate, but nothing can be programmed.
Confirm the output capacitor against the 4 A peak. The part is specified for 4 A at a 3.35 V output from a 2.65 V input, and the transient that follows a load step is handled by the output bank, not by the loop at 2.3 MHz. See incoming inspection plan for the receipt check on a 16 bump chip scale body, where the marking is a single character.
Questions that come up on this part
Can the part run without a battery, is the first question. It can run from a bench supply in the input range, and it will pass the input through when the input is above the threshold, so a 3.8 V supply appears at the output. The second question is whether the pass-through FET is protected against a reverse current. It is not a bidirectional switch, so a load that pushes current back into the output has to be handled by the system.
The third question is about the 3 A valley current limit. It is the inductor current, not the output current, so at a 2.65 V input and a 3.35 V output the available output current is set by that limit and the ratio, which is why the 4 A figure is a peak and not a continuous rating.