TPS61256YFFR
Product Specifications
TPS61256YFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61256YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61256YFFR: 3.5 MHz synchronous boost that holds 5 V from a single lithium cell
TPS61256YFFR is a fixed 5 V step up converter with synchronous rectification, built for a battery input that sits below the output in a DSBGA body of 9 pins. It runs from 2.3 V to 5.5 V and regulates 5.0 V at up to 1000 mA when the input is at 3.3 V or above, with 1500 mA of peak capability. Switching is 3.5 MHz, quiescent current is 37 uA in normal operation and 21 uA in standby, and efficiency reaches 93 per cent at the vendor operating point.
Order code and package
| TPS61256YFFR | 9 pin DSBGA (YFF), 3000 pieces on a large reel |
| TPS61256YFFT | same body, 250 pieces on a small reel |
| Regulated output | 4.92 V minimum, 5.00 V nominal, 5.08 V maximum from a 2.3 V to 4.85 V input |
| Load capability | 1000 mA at 5 V with 3.3 V in, 800 mA at 4.5 V with 2.65 V in, 1500 mA peak |
| Standby current | 21 uA typical with the output held at the input level |
Electrical parameters that decide the application
| Input voltage range | 2.3 V to 5.5 V, and the part keeps working when the input rises above the output |
| Output voltage | 5.0 V fixed on this member, no divider, no adjustment |
| Output current | 1000 mA continuous from a 3.3 V input, 1500 mA peak |
| Switching frequency | 3.5 MHz, which is what keeps the inductor small enough for a phone sized board |
| Quiescent current | 37 uA typical in normal operation, 21 uA in standby with the output biased to the input |
| Efficiency | 93 per cent at the vendor operating point, with the peak around a 3.6 V input |
| Pass through mode | with the input above the output the synchronous rectifier conducts and the output follows the input instead of dropping out |
| Absolute maximum | 7 V on the input, output, switch and enable pins |
| Temperature range | minus 40 C to plus 125 C junction |
How the fixed output members differ
| TPS61253 | 5.0 V, the original member of the family |
| TPS61254 | 5.0 V with a different start up behaviour, for a load that must not see a pre charged output |
| TPS61256 | 5.0 V, 1000 mA at 3.3 V in, the row on this page |
| TPS61257 and TPS61258 | 4.5 V and 3.75 V fixed outputs for rails that are not 5 V |
| TPS61259 and TPS612592 | 5.0 V and 4.3 V members with a different current capability, up to 900 mA from 3.3 V |
| Pass through | all members hold the output near the input when the input rises, which is what makes them usable behind a USB connector |
Points to check before this part goes on a BOM
The 3.5 MHz switching frequency is the whole reason this part is small. At 3.5 MHz the inductor can be 0.7 uH and the output capacitor a few microfarads in an 0402, so the complete converter fits under a square centimetre. The cost is switching loss, and the 93 per cent efficiency figure belongs to a specific operating point rather than to the whole range.
Pass through behaviour matters more than the boost ratio on a USB powered product. When the input rises above 5 V the converter stops boosting and the synchronous rectifier conducts, so the output follows the input minus a small drop instead of regulating down. That is why a product can run from a 5 V charger and a 3.7 V cell without a bypass switch, and why the output must be rated for whatever the adapter can deliver.
The load capability is quoted at two different input voltages for a reason. At 3.3 V in the part delivers 1000 mA at 5 V, at 2.65 V in it delivers 800 mA at 4.5 V, and below that the input current limit becomes the binding constraint rather than the output current. A product that promises 1 A from a nearly empty cell is promising something the converter cannot do at 2.9 V.
The quiescent current has two numbers because the part has two states. In normal operation it is 37 uA, which is high for a battery product but is the price of a 3.5 MHz controller. In standby, with the output held at the input level and the converter not switching, it drops to 21 uA. The state is entered when the input rises above the regulation point, not by a pin, so it cannot be forced on a board that always runs from a low input.
A 9 ball chip scale package on this pitch is assembled like any other wafer level part: it needs a stencil matched to the ball array, and it needs the board to be flat under it. The part has no thermal pad and dissipates through the balls, which is fine at 1 A and 5 V but is worth checking at the top of the current range in a sealed enclosure.
The output is fixed at 5 V, so the part cannot be used for a 5.2 V or a 4.5 V rail without changing to another member of the family. That sounds obvious and it is the most common substitution error on this line: the 4.5 V and 3.75 V members share the pinout and the package, so a reel swapped by part number alone will produce a board that works and a rail that is 10 per cent low.
The absolute maximum of 7 V on the output pin is the number to watch on a product that can be plugged into a 5 V adapter with a transient. A hot plug event on a USB connector routinely produces ringing above 7 V on a short cable, and the part has no clamp of its own. The vendor application circuit puts a capacitor at the input for that reason, and a transient suppressor is cheap insurance on a connector that a user can reach.
Inspection of this part at incoming is limited to the reel label and the date code. The marking is three characters on a body barely a millimetre across, and there is no practical way to tell a 5.0 V member from a 4.5 V member under a microscope. Programs that run more than one member of this family on the same line should keep the reels segregated and verify the label against the purchase order string rather than the bag.
Where this order code fits
It is the boost behind a lithium cell in a handheld product: USB on the go supplies, battery powered instruments, portable speakers and any board where a 5 V rail has to survive a cell that swings from 4.2 V down to 3.0 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What happens when the input is above 5 V? The converter stops boosting and the synchronous rectifier passes the input to the output with a small drop. The output is then whatever the input is, so the downstream parts must be rated for the adapter voltage.
How much current can it deliver from a single cell at 3.0 V? Below the 3.3 V operating point the figure falls toward 800 mA and then to the input current limit. The 1000 mA headline belongs to a 3.3 V input.
Is the output adjustable? No. This member is fixed at 5.0 V, and the family covers 4.5 V, 4.3 V and 3.75 V with other order codes.
Does it need an external Schottky diode? No. The rectifier is synchronous and inside the package, which is why the efficiency holds at 93 per cent and why the part count is one inductor and two capacitors.
What reel sizes are published? YFFR is 3000 pieces on a large reel and YFFT is 250 pieces on a small reel, both active on the current addendum.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.