TPS61120PWR
Product Specifications
TPS61120PWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61120PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61120PWR a boost and a 200 mA LDO in one 16 pin body
The TPS61120PWR combines a synchronous boost converter with a 1.1 A switch and a 200 mA low dropout regulator in a 16 pin TSSOP body, for products that need two rails from a single cell or a two to four cell alkaline pack. The boost takes 1.8 V to 5.5 V in, delivers 500 mA at 3.3 V from a 1.8 V input, and the LDO provides a second output that can be set from 0.9 V to 5.5 V or fixed at the factory.
Total device quiescent current is 40 microamp, which is the sum of a 10 to 25 microamp boost idle current and a 20 to 30 microamp LDO idle current. The boost reference is 500 mV with a 485 mV to 515 mV window, the switch current limit is 1.1 A minimum and 1.6 A maximum around a 1.3 A typical, and the two switch resistances are 200 to 350 milliohm for the NMOS and 250 to 500 milliohm for the PMOS at a 3.3 V output.
The two stages are independent in the sense that the LDO can post regulate the boost output, which removes the boost ripple from the second rail, or it can run from a separate input and supply a completely different voltage. That flexibility is the reason this part exists: one package covers a display rail plus a logic rail, or a 3.3 V analog rail plus a 1.8 V digital rail.
Key parameters from the SLVS427D document
| Input range | 1.8 V to 5.5 V for the boost, 1.8 V to 5.5 V for the LDO input |
| Boost output | Adjustable to 5.5 V against a 500 mV reference, 485 mV to 515 mV window |
| Boost current | 500 mA at 3.3 V from a 1.8 V input, switch limit 1.1 A to 1.6 A |
| LDO output | 200 mA, adjustable 0.9 V to 5.5 V, reverse voltage protected |
| Quiescent current | 40 microamp total, 10 to 25 microamp boost and 20 to 30 microamp LDO |
| Shutdown current | 0.2 to 1 microamp for the boost, 0.1 to 1 microamp for the LDO |
| Switches | 200 to 350 milliohm NMOS and 250 to 500 milliohm PMOS at a 3.3 V output |
| Monitoring | Power good output, low battery comparator, antiringing switch for low emissions |
| Package | 16 pin TSSOP, PW body, published as a 90 piece tube row, moisture level 1 |
Post regulation costs headroom and buys quiet
Feeding the LDO from the boost output removes the switching ripple from the second rail, at the cost of the dropout across the pass element. A 3.3 V boost feeding a 2.8 V LDO output leaves 500 mV for dropout plus the boost ripple, which is comfortable. A 3.3 V boost feeding a 3.0 V output leaves 300 mV, and the LDO dropout at 200 mA is then the limiting factor rather than the boost accuracy.
The reverse voltage protection on the LDO matters when the second rail is held up by another source while the boost is off. Without it, the pass element would see a reverse bias and the body diode would conduct into the boost output. With it, the two rails can coexist during a partial power down, which is common on a product with a USB port and a battery.
The low battery comparator and the power good output give the system two independent signals. The comparator watches the input and warns before the boost loses regulation; the power good watches the boost output and releases the downstream logic. Using the wrong one for the wrong job is how a product ends up resetting during a battery brownout instead of warning the user first.
Where this part fits
Portable instruments with a display rail and a logic rail, battery products that need a clean analog supply, and any board that wants two rails from one package. Our desk keeps the cross reference for combined boost and LDO parts and the second source notes, see power management cross reference and one stop BOM sourcing.
What to check before a purchase order
The addendum prints the TPS61120PWR row as a 90 piece tube rather than the 2000 piece reel that the ordering note in the document describes, so the packing has to be confirmed with the distributor rather than assumed from the suffix. The RSA body of the same part is listed at 2000 pieces on a reel in one row and 3000 in another, which is another reason to read the addendum row rather than the part number.
The output voltage option has to be named. Table 1 of the document lists the adjustable version, the 3.3 V version and the 3.6 V version as separate order codes, and the PWR suffix does not identify which one is inside. A bill that lists only TPS61120PWR will be filled with the adjustable part, which then needs a divider that the board may not have. See incoming inspection plan for the receipt check.
Questions that come up on this part
Can the LDO run from the boost output at the same time as the boost supplies a load, is the first question. It can, and the total current is limited by the boost switch, so 300 mA on the boost rail and 100 mA on the LDO rail is roughly the practical split at a 1.8 V input. The second question is whether the LDO can be disabled independently. It can, through its own enable pin, which is what allows a product to keep the analog rail alive while the display rail is off.
The third question is about the 40 microamp total quiescent current. It is measured with both stages enabled and not switching, so a product that leaves both on in standby pays the full figure. Turning the LDO off drops it by 20 to 30 microamp.