Contact Us

TPS60250RTER

Brand: Texas Instruments
Texas Instruments TPS60250RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS60250RTER — Power Management & Signal Chain | Superb Automation

TPS60250RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS60250RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS60250RTER seven white LEDs on one I2C bus

The TPS60250RTER is a charge pump LED driver for seven white LEDs, split into five for a main display and two for a sub display, in a 16 pin WQFN body measuring 3 mm by 3 mm. It takes 3.0 V to 6.0 V in, converts with a dual mode 1x and 1.5x charge pump at 750 kHz, and sets every current through an I2C interface at address 1110111. The maximum continuous output current is 230 mA.

Each of the seven current sinks is programmable in 64 steps up to 25 mA for the main and sub banks, and there is a fourth group labelled DM5 with 4 steps up to 80 mA for an auxiliary load. Current matching between the sub display LEDs is 2 per cent at a 100 microamp per string light load, which is the figure that decides whether a keypad backlight looks even at low brightness.

The device switches automatically between 1x and 1.5x conversion, so it stays in the efficient direct mode while the battery is above the LED forward voltage plus the dropout of the current sink, and only doubles the conversion ratio when the input falls. That is what keeps efficiency high across a lithium cell discharge rather than only at the top of the curve.

Key parameters from the SLVS769C document

Input range3.0 V to 6.0 V, one lithium cell or a regulated 5 V rail
LED channelsFive main, two sub, plus the DM5 auxiliary group, seven current sinks in total
Current setting64 dimming steps up to 25 mA per main and sub channel, DM5 in 4 steps up to 80 mA
Matching2 per cent channel to channel on the sub display at 100 microamp per string
Charge pumpDual mode 1x and 1.5x, 750 kHz, 230 mA maximum continuous output
InterfaceI2C slave at 1110111, four enable bits for main, sub1, sub2 and auxiliary
ProtectionBuilt-in soft start, current limit and open lamp detection
Package16 pin WQFN, 3 mm by 3 mm, RTE body, 3000 pieces on a large reel
TemperatureMinus 40 to plus 85 degrees ambient on the published rows

The flying and output capacitors set the ripple

All capacitors in the charge pump path have to be the same value for correct operation, and the document states this explicitly. A board that uses a 1 microfarad flying capacitor with a 2.2 microfarad output capacitor will work at room temperature and show a larger ripple and a lower efficiency than the tables, because the charge transfer per cycle is set by the smaller of the two. The 750 kHz frequency means the capacitors can be small ceramics, but they have to match.

The 1x to 1.5x transition is triggered by the voltage across the current sink. When the input falls to the point where a string can no longer be regulated in direct mode, the part switches to the 1.5x ratio and the input current jumps by half again. On a battery that is near its end of discharge, that step is visible as a short dip on the supply rail, and a 10 microfarad capacitor at the input absorbs it.

Open lamp detection is included, so a disconnected LED string is reported rather than silently driven at the limit. On a production line that is the difference between a unit that fails at test and a unit that ships with a dark keypad.

Where this part fits

Handset main and sub displays, keypad and auxiliary backlights, and any product with up to seven white LEDs on a single cell. Our desk keeps the LED driver cross reference and the second source notes, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The RTE body is 16 pins on 3 mm by 3 mm, and the addendum lists the RTER row at 3000 pieces on a large reel and the RTET row at 250 on a small reel. The RTER.B row of the same string also carries 3000 pieces but a different marking code, so the reel label is the only reliable check at goods inwards. The temperature range stops at 85 degrees, which rules this part out for anything that has to run hot.

The I2C address is fixed at 1110111 with no address pin, so two of these devices cannot share a bus. A product with a main display and a separate camera flash driver needs a second bus or a different part. Confirm the maximum main bank current against the 230 mA output limit: five strings at 25 mA is 125 mA, and adding the DM5 group at 80 mA brings the total to 205 mA, which leaves little headroom for the charge pump losses. See incoming inspection plan for the receipt check.

Questions that come up on this part

Can the seven channels be used as seven equal strings, is the first question. The hardware allows it, but the dimming resolution is not the same on all of them, because the DM5 group has four steps rather than 64. The second question is whether the part can run from a 5 V rail. It can, and it will stay in 1x mode almost all the time, which is the efficient case, but the 6.0 V maximum means a 5 V rail with a transient overshoot needs a clamp.

The third question is about the 2 per cent matching figure. It is specified at 100 microamp per string, not at full current, because matching at low current is the hard case. A specification that quotes a single matching number for all brightness levels is quoting the easy end of the range.