TPS60150DRVR
Product Specifications
TPS60150DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS60150DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS60150DRVR: 5 V 140 mA regulated charge pump in a 2 mm by 2 mm six pin SON
TPS60150DRVR is a switched capacitor doubler that produces a regulated 5 V rail from a single lithium cell or a 3.3 V bus using three external capacitors in a WSON (DRV) body of 6 pins. It doubles the input with a flying capacitor and regulates the result to 5 V at up to 140 mA, switching at 1.5 MHz. No inductor is needed, so the whole converter is one flying capacitor and two decoupling capacitors, and the quiescent current falls to 90 microamp in skip mode below about 8 mA of load.
Order code and package
| Order code read out | TPS60150 DRV R: charge pump TPS60150, DRV six pin WSON, R large tape and reel |
| Package | WSON (DRV), 6 pins, 2.0 mm by 2.0 mm by 0.8 mm, junction to ambient 69.1 degrees per watt |
| Carrier in the vendor addendum | TPS60150DRVR at 3000 pieces on a large reel, marked CGO; DRVRG4 is the same reel with the green material code and the RTET style small reel carries 250 pieces |
| Moisture level | Level 1, 260 degrees unlimited floor life |
| Lead finish | Nickel palladium gold, quoted as NIPDAU |
| Temperature grade | Operating free air minus 40 to plus 85 degrees, junction up to 125 degrees |
| Absolute maximum | 7 V on every pin, which is the only supply pin on this device |
Electrical parameters that decide the application
| Input range | 2.7 V to 5.5 V, which covers a lithium cell from 4.2 V down to 3.0 V and a regulated 3.3 V rail |
| Output | 5 V fixed, held between 4.8 V and 5.2 V at full load |
| Output current | 140 mA maximum, and 120 mA when the input is only 3.1 V and the full 4.8 to 5.2 V window has to be held |
| Switching frequency | 1.5 MHz, which is above the audio band and allows small ceramic capacitors |
| Topology | Doubler, so the input current is roughly twice the output current and the input rail has to supply about 280 mA at full load |
| Quiescent current | 4.7 mA while switching with no load, falling to 90 microamp in skip mode below about 8 mA |
| Shutdown current | 1 microamp maximum, with the enable pin pulled low |
| Output ripple | 30 mV typical at 140 mA, which is the figure that decides whether an analogue load needs a further filter |
| Soft start | 150 microseconds internal ramp, so inrush into the output capacitor is bounded |
| Protection | Undervoltage lockout between 1.9 V and 2.1 V, short circuit current limited to 80 mA, and thermal shutdown |
| Enable | 1.3 V minimum for a logic high and 0.4 V maximum for a logic low, so a 1.8 V or 3.3 V pin drives it directly |
| External parts | A 1 microfarad flying capacitor and 2.2 microfarad input and output capacitors |
What this part is and what it is not
| TPS60150DRVR | doubler, 5 V fixed, 140 mA, six pin WSON, the part on this page |
| Boost converter | needed when the output current is above 140 mA or the output voltage has to be adjustable; a charge pump trades flexibility for part count |
| Doubler versus inverter | this device doubles; the same family also carries inverting members for negative rails |
| Skip mode | entered below about 8 mA, where the quiescent current drops to 90 microamp and the output sits about 100 mV above regulation |
| USB on the go | the classic application, where a 3.3 V or battery rail has to produce the 5 V that a peripheral expects |
Points to check before this part goes on a BOM
A charge pump is chosen for part count, not for efficiency. The doubler draws about twice the output current from the input, so 140 mA at 5 V needs roughly 280 mA at 3.3 V, and the best case efficiency is the ratio of the two voltages, about 90 percent at 5.5 V in and about 60 percent at 2.7 V in. A boost converter does better at the low end of the input range and costs an inductor. The decision is usually made by whether the board has room for magnetics and whether the 5 V rail runs continuously.
The 140 mA rating holds only while the input is above 3.1 V. Below that the device can still deliver 140 mA but the output window widens, and the vendor states the 4.8 to 5.2 V guarantee only for the 120 mA case. A build that pulls the full 140 mA from a cell at 3.0 V is outside the regulated window and should be checked on the bench at the end of discharge rather than at nominal.
Skip mode is where the quiescent current falls from 4.7 mA to 90 microamp, and it is entered automatically below about 8 mA of load. In skip mode the output sits roughly 100 mV above the regulated value and the ripple grows, because the device is bursting rather than switching continuously. A load that is sensitive to a 100 mV offset, such as a USB transceiver waiting in suspend, should either stay above the skip boundary or add a small linear regulator after the pump.
The flying capacitor is the component that decides whether the part meets its rating. A 1 microfarad ceramic with a low enough impedance at 1.5 MHz is required, and a part with a poor dielectric or a long trace will lose charge transfer and pull the output down at full load. The same applies to the input capacitor: the current is drawn in bursts at 1.5 MHz, and a 2.2 microfarad part placed more than a few millimetres away leaves the input rail moving with every cycle.
Thermal behaviour is easy to underestimate because the package is small. At 140 mA and 5 V out from 3.3 V in the device dissipates roughly 0.15 W, which on a 69.1 degrees per watt board is a 10 degree rise and is not a concern. A short circuit at the 80 mA limit with a 5 V output is a different matter, and the thermal shutdown is what stops it. The part recovers when it cools, so a permanent short produces a hiccup rather than a dead device.
The undervoltage lockout is published between 1.9 V and 2.1 V, well below the 2.7 V minimum operating input. That means a cell that has collapsed to 2.2 V will still have the converter running and attempting to double, drawing current the cell cannot supply. A product that must stop cleanly at end of discharge needs its own comparator or a supervisor on the cell, because the lockout is not intended as a battery protection threshold.
Where this order code fits
Used for USB on the go supplies, HDMI and display bias rails, portable instrument 5 V rails, PCMCIA and card slot supplies and any small 5 V load that has to come from a single lithium cell without an inductor. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Consolidation page.
Questions buyers ask
Why does the input current exceed the output current? It is a doubler, so charge is transferred at twice the output voltage. At 140 mA out the input draws about 280 mA, plus losses, which is why the input capacitor and the source impedance matter as much as the output ones.
Can it deliver 140 mA from a 3.0 V cell? The full 4.8 to 5.2 V window is only guaranteed to 120 mA when the input is 3.1 V. Above 3.1 V the 140 mA figure applies. A product that runs to the end of cell discharge should be tested at 3.0 V rather than at nominal.
What happens at light load? Below about 8 mA the device enters skip mode, the quiescent current falls from 4.7 mA to 90 microamp, and the output rises about 100 mV above regulation with more ripple. That is a deliberate trade for standby efficiency.
Does it need an inductor? No. The converter is a switched capacitor doubler with one flying capacitor and two decoupling capacitors. That is the reason it exists, and it is also the reason its efficiency falls at low input voltage.
Is it protected against a shorted output? Yes, the output current is limited to about 80 mA and the device has thermal shutdown. The recovery is automatic once the short is removed, so a permanent fault produces a repeating hiccup rather than a latched failure.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.