Contact Us

TPS56A37RPAR

Brand: Texas Instruments
Texas Instruments TPS56A37RPAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS56A37RPAR — Power Management & Signal Chain | Superb Automation

TPS56A37RPAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS56A37RPAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS56A37RPAR 10 A from a 28 V input with a 45 microamp idle draw

The TPS56A37RPAR is a 4.5 V to 28 V, 10 A synchronous buck in a 10 pin VQFN-HR body measuring 3 mm by 3 mm. It integrates a 19.4 milliohm high side and an 8.5 milliohm low side FET, holds a 0.6 V reference at 1 per cent at 25 degrees, and delivers between 0.6 V and 13 V at the output. The switching frequency is 500 kHz at 24 V in and 5 V out in continuous conduction.

The number that separates this device from the rest of the 10 A class is the quiescent current: 45 microamp typical with the enable pin high and the converter not switching, and 3 microamp in shutdown. Most 28 V capable converters at this current draw ten times that at idle, which is why they cannot be used on a rail that has to meet a standby budget in a product that is plugged in all the time.

Control is D-CAP3 with no external compensation and an Eco-mode that lets the frequency fall at light load. Soft start is 1.8 ms with a 6 microamp charge current, a power good output is provided with 85 to 90 per cent and 110 to 115 per cent windows, and the protection set covers undervoltage, overvoltage, overcurrent and thermal shutdown.

Key parameters from the SLVSHC9 document

Input range4.5 V to 28 V, UVLO with a 3.5 V to 3.8 V hysteresis window
Output current10 A continuous from a 19.4 milliohm high side and an 8.5 milliohm low side FET
Output voltage0.6 V to 13 V against a 0.6 V reference at 1 per cent at 25 degrees
Switching frequency500 kHz at 24 V in and 5 V out in continuous conduction
Current limitLow side valley 10 A to 13.8 A, high side peak 12.75 A to 17.25 A, negative 2.5 A
Quiescent current45 microamp typical and 3 microamp shutdown at 25 degrees
Soft start1.8 ms internal, 6 microamp charge current
Enable and power goodEnable rising 1.18 V to 1.26 V, power good windows at 85 to 90 and 110 to 115 per cent
Package10 pin VQFN-HR, 3 mm by 3 mm, RPA body, 3000 pieces on a large reel, moisture level 2

28 V input at 10 A changes the failure modes

A converter that accepts 28 V has to survive the transients that come with a 24 V industrial bus, and the switch node sees the full input plus the ringing of the parasitic inductance between the input capacitor and the FETs. The 500 kHz frequency helps, because the current ripple in the inductor is larger and the loop reacts faster, but it also means the input ceramic bank has to be close to the part rather than at the connector.

The second failure mode is a shorted load at 24 V input. The high side peak limit of 12.75 A to 17.25 A will trip on the first cycle, and the valley limit on the low side at 10 A to 13.8 A will hold the average current down while the hiccup counter runs. An inductor that saturates below 17.25 A will present a low impedance before the limit acts, and the resulting current is limited only by the input source. Size the inductor against the top of the peak window, not against the 10 A rating.

Thermally, 10 A from 24 V to 5 V puts about 1.4 W of conduction loss in the low side FET at the 8.5 milliohm figure and about 0.2 W in the high side, before switching. A 3 mm by 3 mm body passes that through the thermal pad into the board, so an inner copper plane is part of the circuit rather than a nicety.

Where this part fits

24 V industrial buses, telecom line cards, PoE powered equipment and any board that needs 10 A with a low idle draw. Our desk keeps the cross reference for the wide input class and the second source notes, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The RPA body is 10 pins on 3 mm by 3 mm and the order code is the only field that separates it from the smaller members of the family. The addendum lists TPS56A37RPAR at 3000 pieces on a large reel with moisture level 2, so the reel needs dry storage and the floor life clock starts when it is opened.

The power good windows are worth checking against the load. The lower window opens at 85 to 90 per cent of the feedback voltage, which on a 1.0 V rail is 0.85 V to 0.90 V, and a processor that needs its reset released only after the rail is within 5 per cent will see the power good assert early. If that matters, the enable of the downstream device has to be delayed by its own supervisor rather than by this output. See incoming inspection plan for the receipt check and component lead time solutions when the reel is short.

Questions that come up on this part

Is 13 V output really available at 10 A, is the first question. The output range allows it, but the duty cycle at 28 V in and 13 V out is 46 per cent, and the ripple current in the inductor is then set by the 500 kHz frequency and the inductance, so the inductor value has to be chosen for that operating point rather than for the 5 V case. The second question is whether the 45 microamp figure holds at 85 degrees. It is a 25 degree number, and the idle current of any converter rises with temperature because the internal references and comparators draw more.

The third question is about the Eco-mode boundary. Below a few hundred milliamps the part starts to skip, and the output ripple becomes a burst pattern. On a rail that feeds a Class D amplifier or a radio, that pattern can land in band, and the fix is either a forced continuous part or a small LC filter after the converter.