TPS54J060RPGR
Product Specifications
TPS54J060RPGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54J060RPGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54J060RPGR: 4 V to 16 V input 6 A synchronous buck converter with D-CAP3 control in a 14 pin QFN
TPS54J060RPGR is an adaptive on-time D-CAP3 buck with both power FETs inside the package, a 0.9 V reference and a current limit set by one resistor, so no compensation network sits outside the part in a VQFN-HR (RPG) body of 14 pins. It takes 4 V to 16 V on the input, or 2.7 V to 16 V when a 3.3 V bias is fed to the VCC pin, holds the output between 0.9 V and 5.5 V and passes 6 A continuously. The internal FETs measure 22 milliohm on the high side and 8.5 milliohm on the low side at 25 degrees, and the reference stays inside 891 to 909 mV over the full minus 40 to plus 125 degree junction range.
Order code and package
| Order code read out | TPS54J060 RPG R: converter TPS54J060, RPG fourteen pin VQFN-HR, R large tape and reel |
| Package | VQFN-HR (RPG), 14 pins, 3.0 mm by 2.0 mm, 0.5 mm pitch, HotRod body with the FET pads on the underside |
| Carrier in the vendor addendum | TPS54J060RPGR at 3000 pieces on a 330 mm reel; the .A and .B rows are the same reel with different material declarations; there is no small reel row for this part |
| Moisture level | Level 2, 260 degrees peak reflow, one year floor life |
| Lead finish | Tin, quoted as SN |
| Temperature range | Junction minus 40 to plus 125 degrees, storage minus 55 to plus 150 |
| Absolute maximum | 18 V on VIN and on VIN to SW, 24 V on BOOT to PGND, 21.5 V on BOOT to SW, 6 V on EN, PGOOD, TRIP, MODE, SS/REFIN and FB, SW to PGND minus 4 V to 25 V for a 20 ns transient |
Electrical parameters that decide the application
| Input range | 4 V to 16 V with the internal LDO feeding the gate drive, 2.7 V to 16 V when 3.3 V is applied to VCC |
| Output range | 0.9 V to 5.5 V set by a divider against the 900 mV reference |
| Output current | 6 A continuous through the integrated FET pair, with the valley current limit bounded at 9.5 A even with the TRIP pin shorted to ground |
| Reference accuracy | 900 mV nominal, 891 to 909 mV over minus 40 to plus 125 degrees, which is plus or minus 1 percent end to end |
| Switching frequency | Three settings chosen by the resistor on the MODE pin: 600 kHz, 1100 kHz and 2200 kHz, with a 60.4 kohm resistor giving 630 kHz typical and 536 to 724 kHz across units |
| High side FET | 22 milliohm at 25 degrees with 3 V across the bootstrap and 3 A flowing |
| Low side FET | 8.5 milliohm at 25 degrees, the device that carries the inductor current for the larger part of each period at low duty cycle |
| Current limit | Valley sensing on the low side FET; the TRIP resistor runs from 3.74 kohm to 30.1 kohm, the constant is 30000, and 4.99 kohm gives 6.0 A typical with a 5.1 to 6.9 A window |
| Negative current limit | Minus 3.5 A typical, minus 2.8 to minus 4.3 A across units, which is the floor when the output is pulled down by an external source |
| Protection thresholds | Overvoltage trips at 116 percent of nominal, undervoltage at 80 percent, and both latch the part off rather than retrying |
| Power good | The open drain PGOOD releases at 92.5 percent of the reference on the way up and pulls low below 80 percent or above 116 percent, with a 1.25 ms release delay and a 5 microsecond pull down |
| Soft start | Internal ramp of 1 ms typical and 1.5 ms maximum with a 1 nF capacitor on SS/REFIN, which also accepts an external ramp for tracking |
| Quiescent current | 900 microamp typical with no external bias, rising to 3 mA, 5.5 mA or 10 mA at 600 kHz, 1100 kHz and 2200 kHz when VCC is biased at 3.3 V |
| Internal LDO | 3.00 V at the VCC pin with a 60 mA overcurrent limit, so the bias pin can carry light housekeeping loads |
| Thermal | 64 degrees per watt junction to ambient on a JEDEC board, 43.5 degrees per watt on the vendor evaluation board |
Rows of the same order code and the pins that change behaviour
| TPS54J060RPGR | the part on this page, 3000 pieces on a large reel, production status |
| RPGR.A and RPGR.B | the same device and the same reel qty with separate material declarations, which is what a customer asking for a specific finish or green declaration will be quoted against |
| MODE pin | sets forced continuous conduction or skip mode and also picks the frequency, so the resistor value is part of the order definition rather than a tuning detail |
| TRIP pin | the current limit resistor; below 3.16 kohm the limit is clamped at 9.5 A, and the usable window is 3.74 kohm to 30.1 kohm |
| SS/REFIN pin | an internal 1 ms ramp by default, an external capacitor for a slower start, or a voltage for tracking a second rail |
Points to check before this part goes on a BOM
D-CAP3 closes the loop inside the package, so there is no compensation pin and no external network to tune. The output capacitor is part of the control loop instead of being a filter after it, and the data sheet states the capacitance and ESR window that keeps the loop stable. A build that fits a much smaller ceramic capacitor than the window asks for will show jitter or a slow oscillation that reads like a board fault rather than a component choice.
The external bias on VCC is worth understanding before the board is laid out. With no bias the internal LDO makes 3.0 V from the input and burns the difference, which costs 3 mA at 600 kHz and 10 mA at 2200 kHz drawn from VIN. Feeding 3.3 V into VCC removes most of that loss, and the input range then starts at 2.7 V rather than 4 V, which is what allows a 3.3 V bus to be stepped down by this part.
The current limit is set by a resistor and is therefore predictable on paper. The constant is 30000, so a 4.99 kohm resistor gives a 6 A valley limit and a 10 kohm resistor gives about 3 A, with the caveat that the tolerance widens from plus or minus 10 percent in the 3.74 to 4.99 kohm range to plus or minus 16.5 percent at 10 kohm. Valley sensing means the peak inductor current sits above the limit by half the ripple, so the inductor value and the frequency both move the real trip point.
Overvoltage and undervoltage both latch off, which is a deliberate choice for a point of load rail feeding a processor: the part does not restart into a fault until the enable pin is cycled or the input is removed. A board that expects automatic recovery after a transient will look dead until someone toggles EN, and that behaviour has to be written into the bring up procedure rather than discovered on the bench.
The MODE pin does two jobs. It selects skip mode, where the part stops switching at light load and lets the output ripple grow, or forced continuous conduction, where it keeps switching and holds the ripple and the frequency constant. It also picks one of the three frequencies. For a rail that feeds an analogue front end or a radio, forced continuous conduction at 1100 kHz or 2200 kHz is the usual pick; for a standby rail that spends most of its life at a few milliamps, skip mode at 600 kHz keeps the quiescent draw in the hundreds of microamps.
The thermal number is worth quoting to a customer who asks about 6 A in a 3 by 2 mm body. On a JEDEC board the junction to ambient resistance is 64 degrees per watt, against 43.5 on the vendor evaluation board, so the copper under the part decides the rating more than the package does. At a 1 V output from 12 V the conduction loss in the two FETs is roughly 0.9 W at 6 A, which against 43.5 degrees per watt puts the junction about 39 degrees over ambient and against 64 degrees per watt puts it about 58 degrees over.
Where this order code fits
Serves point of load rails for servers, networking and optical line cards, wireless infrastructure, industrial PCs and IP cameras, where a 12 V or 5 V bus has to become 0.9 V to 5.5 V at up to 6 A in a 3 mm by 2 mm area. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Does this converter need an external compensation network? No. D-CAP3 is an adaptive on-time loop closed inside the package, and the data sheet gives the output capacitor and ESR window that keeps it stable. The value of the output capacitor is therefore a circuit parameter, not a leftover, and a much smaller ceramic part than the table asks for is the usual cause of jitter.
What does the VCC pin do and can it take a bias? VCC is the output of an internal 3.0 V LDO that feeds the control circuits and the gate driver, and it accepts a 3.3 V plus or minus 5 percent external bias. With the bias applied the input range starts at 2.7 V instead of 4 V and the bias current falls from 3 to 10 mA drawn from VIN depending on frequency.
How is the current limit set? A resistor from TRIP to ground, using the 30000 constant divided by the wanted valley current. 4.99 kohm gives 6.0 A typical and 10 kohm gives about 3 A, with plus or minus 10 percent tolerance in the lower range and wider tolerance at 10 kohm.
What happens after an overvoltage or undervoltage fault? The part latches off. It does not retry by itself, so recovery needs the enable pin to be cycled or the input to be removed. Overvoltage trips at 116 percent of nominal and undervoltage at 80 percent.
Which reel comes with a production order? The R suffix is 3000 pieces on a 330 mm reel and is the only carrier listed for this device. The .A and .B rows are the same reel with different material declarations rather than a different quantity.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.