Contact Us

TPS548D22RVFR

Brand: Texas Instruments
Texas Instruments TPS548D22RVFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS548D22RVFR — Power Management & Signal Chain | Superb Automation

TPS548D22RVFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS548D22RVFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS548D22RVFR 40 A pin strapped buck with a selectable 0.6 V to 1.2 V reference

The TPS548D22RVFR is a 40 A synchronous buck in a 7 mm by 5 mm, 40 pin LQFN, with 2.9 milliohm high side and 1.2 milliohm low side FETs. It has no PMBus. Everything it does is set by pins, and that is the whole point of the part: a 40 A rail that boots correctly with no bus master, no configuration file and no sequencing software. Four switching frequencies are available on a pin, 425 kHz, 650 kHz, 875 kHz and 1.05 MHz.

The reference is the interesting part. VSEL scales the internal reference from 0.6 V to 1.2 V in 50 mV steps, which means the same feedback divider can produce different output voltages by strapping VSEL differently. In a family of boards that differ only in core voltage, that removes a component change from the bill and moves the difference to a strap. The reference tolerance is 0.5 per cent against a 0.9 V nominal over 40 to 125 degrees junction, and the sense is a true differential pair, so the loop regulates at the load rather than at the nearest bulk capacitor.

Current limit is set by a resistor on RILIM and is temperature compensated, with an OC clamp behind it. Overvoltage and undervoltage can be set to hiccup or to latch off by pin, which matters when a rail feeds a processor that must survive a transient but must not survive a sustained overvoltage.

Key parameters from the SLUSC70D document

Input range1.5 V to 16 V on PVIN, 4.5 V to 22 V on VDD for the bias and the gate drive
Output current40 A continuous in the 40 pin LQFN with the exposed pad soldered to a copper island
Output voltage0.6 V to 5.5 V, with the reference scaled 0.6 V to 1.2 V in 50 mV steps by VSEL
Power FETs2.9 milliohm high side and 1.2 milliohm low side
Switching frequencyFour pin selectable settings: 425 kHz, 650 kHz, 875 kHz and 1.05 MHz
Reference accuracy0.5 per cent against a 0.9 V nominal over 40 to 125 degrees junction
Current limitRILIM resistor, temperature compensated, with an OC clamp behind it
Fault handlingHiccup or latch off selectable for overvoltage and undervoltage, full protection suite with PGOOD
Package40 pin LQFN-CLIP, 7 mm by 5 mm, RVF body, RoHS exempt

The VSEL reference and what it saves

A 1.0 V core rail and a 0.9 V core rail normally need two different feedback dividers and therefore two different bills and two different assembly checks. With the reference scaled by pin, the same divider produces both, and the board difference is a strap. On a program that ships several processor options this removes a whole class of build error, because the wrong divider value is a silent fault while a wrong strap is visible at test.

The cost is resolution. Fifty millivolt steps on the reference translate to a coarse output step, so a rail that needs 0.875 V exactly cannot be reached by strap alone. The document gives the divider equation against the selected reference, and the right practice is to pick the strap first and then compute the divider, not the other way round.

Thermal behaviour at 40 A

At 40 A and 1.2 milliohm, the low side conduction loss is about 1.9 W at full load in a 1 V to 12 V conversion, and that number dominates the thermal budget. The body is 7 by 5 mm, so the heat leaves through the pad and the copper under it. A board that reduces the via count under the pad to make room for signal routing will hold 40 A only at low ambient. The document's thermal section gives the copper area and via pattern the ratings assume.

Eco mode drops the switching losses at light load by entering a skip pattern, and forced continuous conduction keeps the ripple small at the cost of circulation loss. On a rail that idles at a few hundred milliamps but must answer a fast load step, forced continuous conduction is usually the right setting, because the skip pattern hurts the transient response more than it saves.

Where this part fits

Processor and FPGA core rails, DDR memory rails where the reference scaling helps, and any 40 A point of load stage on a board with no bus master. The absence of PMBus is a feature on industrial and medical boards where a configuration interface adds validation burden. See power management cross reference for how we compare it against the PMBus member of the family.

What to check before a purchase order

The RVF body is the 40 pin LQFN-CLIP, 7 by 5 mm, and the same family string also appears in other bodies. The part is RoHS exempt rather than compliant on the published rows, so a customer with a compliance clause needs that stated on the quote rather than discovered at the customs document. Confirm the VSEL strap and the RILIM resistor against the intended rail before building, because both are silent if wrong.

See incoming inspection plan for how we handle exempt finish parts, and one stop BOM sourcing for the rail group.

Questions that come up on this part

Can the 40 A part be used at 15 A, is a common question. Yes, but the RILIM resistor has to be rescaled, otherwise the limit sits far above what the downstream copper can carry. The second question is whether the four frequency settings can be changed after build. Only by changing the strap resistor, which is why the frequency should be chosen before the inductor is fixed.