Contact Us

TPS54620RGYR

Brand: Texas Instruments
Texas Instruments TPS54620RGYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54620RGYR — Power Management & Signal Chain | Superb Automation

TPS54620RGYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54620RGYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54620RGYR 6 A synchronous buck with a split PVIN rail down to 1.6 V

The TPS54620RGYR is a 17 V input, 6 A synchronous step down converter in a 3.5 mm by 3.5 mm QFN, with 26 milliohm high side and 19 milliohm low side FETs inside the body. The feature that sets it apart from most parts in this current range is the split rail: VIN feeds the control circuits at 4.5 V to 17 V while PVIN feeds the power stage from 1.6 V to 17 V. That second pin is what makes the part usable as a point of load stage on a 1.8 V or 2.5 V bus, where a single rail part cannot start at all.

Control is current mode with an external compensation network on COMP, so the loop can be tuned for a large bulk capacitor bank or for a bank of small ceramics. Switching runs from 200 kHz to 1.6 MHz, set by a resistor on RT/CLK, or synchronized to an external clock on the same pin. At 6 A with 19 milliohm on the low side, 1 MHz is realistic on a four layer board, which is what keeps the inductor and the output bank small in a dense point of load row.

Two pins do the sequencing work. SS/TR carries a capacitor for a controlled ramp, or a divider for tracking a second rail, because the voltage on that pin overrides the internal reference. PWRGD is an open drain output that pulls low on undervoltage, overvoltage, thermal shutdown, EN shutdown or during the ramp. Between SS/TR and PWRGD a multi rail board gets its power up order without an external sequencer.

Key parameters from the SLVS949F document

Input range4.5 V to 17 V on VIN, 1.6 V to 17 V on PVIN, 20 V absolute maximum on both
Output current6 A continuous, output from 0.8 V up to the input less the drop across the high side FET
Power FETs26 milliohm high side and 19 milliohm low side at 12 V input, both inside the 14 pin QFN
Switching frequency200 kHz at a 240 k resistor on RT/CLK, 480 kHz at 100 k, 1.6 MHz at 29 k, and external clock sync on the same pin
Reference0.8 V with 1 per cent initial accuracy, and the SS/TR pin overrides it for tracking
Quiescent current2 microamp typical in shutdown with EN low
Timing limits94 ns typical minimum on time and 91 ns minimum off time, measured at 2 A on the PH pin
ThermalThermal shutdown at 175 degrees typical with 10 degrees of hysteresis, junction range 40 to 150 degrees
Package14 pin VQFN, 3.50 mm by 3.50 mm, exposed pad soldered to ground for the heat path

Where the split rail earns its place

A 5 V to 1.2 V conversion is the obvious case: PVIN sits on the 5 V bus and VIN can sit on the same bus, and the duty cycle of 24 per cent at 480 kHz is far from the 94 ns minimum on time. The subtler case is a 1.8 V bus feeding a 1.0 V core. A single rail part needs its own bootstrap and its own minimum input, while this one runs PVIN at 1.8 V with VIN fed from the 12 V housekeeping rail, which keeps the gate drive strong even when the power rail sags under a transient.

The current mode loop with an external COMP network is not a drawback on a board with a known output capacitor. It is the way to place a compensation zero where the output capacitor ESR corner actually sits, and it lets a 6 A stage drive several hundred microfarad of polymer without the loop going soft. Boards that change output capacitors late in a program are the ones that notice this.

Protection behaviour worth knowing before a fault

The high side FET carries cycle by cycle current limiting, and behind it sit a low side sourcing limit that stops current runaway when the inductor saturates and a low side sinking limit that turns the low side FET off when reverse current flows in from the output. A persistent overload therefore ends in a limited, ticking pattern rather than a shorted FET. Thermal shutdown at 175 degrees clears itself once the die cools, so a supply that restarts on its own at high ambient is telling you about thermal resistance, not about the load.

Monotonic start into a prebiased output matters in systems where a second rail is already alive. The part holds the low side off until the internal ramp passes the sensed voltage, so the output does not get pulled down before it comes up. That single behaviour removes a latch up path on FPGAs and DSPs that power their I/O before their core.

Where this part fits

High density distributed power, point of load regulation for processors, and broadband, networking and optical line cards are the three uses named in the document, and they share one property: a low voltage bus, a tight board, and a load that steps fast. For a desk quoting this class of board the sourcing question is usually the reel behind the part and the cross reference to the next family member, which is where power management cross reference and one stop BOM sourcing come in.

What to check before a purchase order

Three fields decide whether a quoted reel is the right one. The first is the package suffix: RGY is the 3.5 mm QFN and RHL is the same die in a different body, and the two do not share a footprint. The second is the marking on the top of the part, because a distributor listing for the family can point at a neighbour. The third is the date code on the reel, since a 2009 architecture still shipping in volume means stock that has been on a shelf somewhere.

Our desk checks all three against the customer bill of materials before quoting, and when a lead time moves we show the pin compatible alternative with the differences spelled out rather than a bare substitution. See component lead time solutions for the format we use.

Questions that come up on this part

Is the split rail mandatory, asks one buyer a week. No. VIN and PVIN can be tied together on any bus from 4.5 V to 17 V, and the split only becomes necessary below 4.5 V or when the gate drive has to stay stiff on a sagging bus. The second question is whether 6 A is a thermal rating or an electrical one. It is electrical at 25 degrees with the exposed pad soldered down; the real limit is the junction temperature at the ambient of the enclosure, which is why the thermal numbers in the document assume a specific copper area.