TPS54335ADRCR
Product Specifications
TPS54335ADRCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54335ADRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54335ADRCR: 4.5 V to 28 V input, 3 A synchronous buck converter with adjustable frequency
TPS54335ADRCR is a wide input synchronous step-down converter with an internal low-side FET and a frequency that can be set from 50 kHz to 1.5 MHz in a VSON (DRC) body of 10 pins. It takes 4.5 V to 28 V in, delivers 3 A from 128 milliohm and 84 milliohm FETs, and lets the board set the switching frequency with one resistor, which is the difference between a 28 V industrial rail and a converter that has to be shielded.
Order code and package
| Ordering string | TPS54335ADRCR, DRC package, 10-pin VSON, tape and reel |
| Family members | TPS54335A (2 ms internal soft start, adjustable frequency), TPS54336A (adjustable soft start, fixed 340 kHz) |
| Package | 10-pin VSON, 3 mm by 3 mm, and an 8-pin SO PowerPAD option |
| Ambient range | Junction -40 C to 150 C |
| Frequency | 50 kHz to 1.5 MHz set by RT, with a 40 kHz to 60 kHz floor if the resistor is left open |
| Output range | 0.8 V reference up to the input voltage less the drop across the high-side FET |
Electrical parameters that decide the application
| Input range | 4.5 V to 28 V |
| Output current | 3 A continuous |
| Switch resistance | 128 milliohm high side, 84 milliohm low side |
| Reference | 0.8 V, plus or minus 0.8 percent at 25 C and 1.5 percent over temperature |
| Shutdown current | 2 microamp with the enable pin low |
| Minimum on time | 94 ns typical, which caps the duty at high input and low output |
| Minimum off time | 145 ns typical |
| Soft start | 2 ms internal ramp on the A suffix |
| Thermal shutdown | 175 C typical with 10 C hysteresis, hiccup restart |
Points to check before this part goes on a BOM
The 94 ns minimum on time is the limit that decides whether a 28 V to 3.3 V rail is possible at a given frequency. At 500 kHz the period is 2 microsecond and 3.3 V over 28 V is 11.8 percent duty, or 236 ns of on time, which is comfortable. At 1.5 MHz the period is 667 ns and the same duty needs 79 ns, which is below the minimum, so the converter will skip pulses and the output will show a low frequency beat rather than a clean 1.5 MHz ripple.
The frequency resistor is also the efficiency control. Lower frequency means lower switching loss and a larger inductor, higher frequency means a smaller inductor and more loss in the FETs and the gate drive. On a 24 V to 5 V conversion at 3 A, going from 300 kHz to 1 MHz roughly doubles the switching loss, which at this current is a few tenths of a watt, so the 300 kHz to 500 kHz range is the usual industrial choice.
Hiccup over current protection waits between 512 and 16384 cycles before retrying, which at 500 kHz is between 1 ms and 33 ms. That is deliberate: a shorted output is retried slowly so the input supply is not loaded continuously, and a transient that trips the limit briefly recovers without a visible restart. A load that draws a genuine 120 percent for 20 ms will therefore see the rail disappear rather than fold back, which is the behaviour a motor or lamp load has to be checked against.
The reference is 0.8 V, which is higher than the 0.6 V used by most parts in this class. For a 1.0 V output the divider ratio is only 1.25, so the top resistor is small and the divider current is larger than a 0.6 V divider would need. For a 0.9 V rail the ratio is 1.125 and the divider error from bias current becomes the dominant term, which is the case where a 0.1 percent divider is not optional.
The internal low-side FET removes the Schottky diode that a non-synchronous converter would need, but it also means the part cannot sink current in discontinuous mode without the low-side sinking limit acting. In a pre-biased start the output is already charged, and the monotonic startup feature keeps the converter from pulling that node down, which is what allows the rail to come up second in a sequencing chain.
At 3 A and 128 milliohm the high-side conduction loss is 0.29 W at 25 percent duty, and the low-side 84 milliohm carries 0.57 W at 75 percent duty, so the low-side FET is the hotter of the two even though it has the lower resistance. That is the opposite of what most people assume from the resistance numbers, and it is the reason the thermal pad and the copper under the part matter more than the headline efficiency curve.
Where this order code fits
It suits 12 V and 24 V industrial buses, car audio and battery charger supplies, set top boxes, LCD panels, smart meters and any board that has to make 5 V, 3.3 V or 1.8 V from a rail that can reach 28 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What happens if the frequency resistor is missing? The converter falls back to an internal 40 kHz to 60 kHz setting, so it still runs, but the inductor and the output capacitor have to be sized for that frequency or the ripple will be far above the calculation.
Is the part pin compatible with the fixed frequency version? The TPS54336A is the same family with a fixed 340 kHz setting and an adjustable soft start, so the body and the pinout are shared and the difference is in the function of two pins.
Can it run from a 28 V rail continuously? Yes, 28 V is the top of the recommended range, and the input capacitor has to be rated above that with margin for the transient the rail actually carries.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.