Contact Us

TPS54326RGTR

Brand: Texas Instruments
Texas Instruments TPS54326RGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54326RGTR — Power Management & Signal Chain | Superb Automation

TPS54326RGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54326RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54326RGTR: 4.5 V to 18 V input 3 A synchronous step down converter in a 16 pin QFN

TPS54326RGTR is an adaptive on-time D-CAP2 buck regulator with both power FETs inside the package, so the inductor and the output capacitor are the only power components outside in a VQFN (RGT) body of 16 pins. It runs from a 4.5 V to 18 V rail on the control supply and a 2 V to 18 V rail on the power input, holds the output anywhere from 0.76 V to 5.5 V and switches at a fixed 700 kHz. The internal FETs measure 120 milliohm on the high side and 70 milliohm on the low side, and the feedback reference is 0.765 V with a window that stays inside 751 to 779 mV over the rated temperature range.

Order code and package

Order code read outTPS54326 RGT R: converter TPS54326, RGT sixteen pin VQFN, R large tape and reel
PackageVQFN (RGT), 16 pins, 3.0 mm by 3.0 mm, exposed thermal pad on the underside
Carrier in the vendor addendumTPS54326RGTR at 3000 pieces on a 330 mm reel; RGTT is the same part on a 180 mm reel of 250 pieces; RGTRG4 is the same reel with the green material code
Moisture levelLevel 2, 260 degrees peak reflow, one year floor life on the RGTR row; the .A and .B rows of the same order code are listed at Level 1 unlimited
Lead finishNickel palladium gold, quoted as NIPDAU
Temperature gradesOperating free air minus 40 to plus 85 degrees, junction minus 40 to plus 125 degrees
Absolute maximum20 V on VIN, VCC and EN; 26 V on VBST; 6.5 V on VBST with respect to SW; 20 V on SW for a 10 ns transient

Electrical parameters that decide the application

Control supply range4.5 V to 18 V on VCC, which is the rail that must be present before the part will start
Power input range2 V to 18 V on VIN, so a 3.3 V bus can feed the drain of the high side FET while VCC comes from a 5 V or 12 V housekeeping rail
Output range0.76 V to 5.5 V set by a divider against the 0.765 V reference
Output current3 A continuous, protected by a cycle by cycle limit of 3.5 A minimum, 4.1 A typical and 5.5 A maximum
Switching frequency700 kHz fixed internally, which sets the inductor to the 1.0 to 2.2 microhenry region for a 5 V output
High side FET120 milliohm at 25 degrees with 5.5 V across the bootstrap, so 3 A costs about 1.1 W of conduction in that device alone at full duty
Low side FET70 milliohm at 25 degrees, which carries the current for the rest of the cycle
Feedback window751 to 779 mV over minus 40 to plus 85 degrees, which is plus or minus 1.8 percent end to end
Internal LDO5.5 V at the VREG5 pin, 5.3 to 5.7 V over the range, able to source 70 mA for external housekeeping
Quiescent current850 microamp typical and 1300 microamp maximum while regulating without switching; 1.8 microamp typical and 10 microamp maximum shut down
Power goodThe PG pin pulls low when the feedback falls below 85 to 95 percent of the reference, so the window is a band rather than a point
ProtectionCycle by cycle current limit, thermal shutdown at 150 degrees, and a soft start ramp set by one capacitor on the SS pin

Family variants and the parts that sit beside it

TPS54326RGTRthe part on this page, 3 A, fixed 700 kHz, D-CAP2, 16 pin QFN
TPS54326PWPRthe same die in the 14 pin HTSSOP body, chosen when a leaded package is easier to inspect
RGTT rowthe same part on a 250 piece reel, which is what a prototype or a small build normally needs
TPS54325 and TPS54328neighbouring members of the same D-CAP2 family with different current ratings and frequency, worth checking before a socket is committed
Eco-modethe light load behaviour that drops the switching frequency instead of skipping cycles outright, and the reason standby efficiency stays high

Points to check before this part goes on a BOM

This is a D-CAP2 part, which means there is no external compensation network and no error amplifier pin to tune. The loop is closed internally against the output ripple, so the output capacitor is part of the control loop rather than just a filter. The data sheet gives a supported capacitance and ESR window, and a build that fits a much smaller ceramic capacitor than the table asks for will show jitter or a slow oscillation that looks like a routing fault. Teams moving a board from an older voltage mode part should treat the output capacitor as a circuit parameter, not a leftover.

The two supply pins are the feature that makes this part useful on a mixed rail board. VCC needs 4.5 V to start the internal regulator and the gate drive, while VIN only needs 2 V. That allows a 3.3 V or even a 2.5 V bus to be stepped down while the control supply comes from a 12 V housekeeping rail that is already there. It also means the VCC pin has to be sequenced, and a board that brings VIN up first and VCC second will simply not start until the second rail arrives, which is sometimes mistaken for a dead part.

The 3 A rating and the 4.1 A typical current limit are close together, which is normal for a converter that is expected to survive a short circuit rather than a sustained overload. At a 5 V output from 12 V the duty cycle is about 42 percent, so the high side FET conducts for less than half the period and the conduction loss is about 0.5 W; at 18 V in the same 3 A costs less than 0.3 W in that FET but the switching loss rises. The hot case for this device is a high input, high ambient build, not the low input one.

Eco-mode changes the picture at light load. Below the point where the inductor current would reverse, the part reduces the switching frequency and lets the output ripple grow, which is how it keeps efficiency respectable at a few milliamps. A load that is sensitive to ripple, such as an analogue front end or a radio, should either stay above the Eco-mode boundary or accept a larger output capacitor. The mode is automatic and has no pin, so the only way to control it is through the load and the output capacitor.

The VREG5 pin is a real 5.5 V LDO with 70 mA of available current, and it is tempting to hang housekeeping loads on it. At an 18 V input that LDO dissipates 0.9 W at full 70 mA, which is more than the converter itself loses at 3 A in many builds, and it raises the junction temperature of the whole package. A small external load is fine; a second converter hung on that pin is not, and the thermal calculation has to include it.

The power good window is quoted as a band from 85 to 95 percent of the reference, which is a 10 percent spread between units. A sequencer that waits for PG before enabling the next rail therefore waits a different length of time on different boards. That is usually harmless, but a board that relies on the exact point where PG releases, for example to start an ADC calibration, should use its own comparator on the rail instead.

Where this order code fits

Fits set top boxes, digital televisions, industrial controllers, access points and instrumentation that need a 5 V, 3.3 V or 1.8 V rail at up to 3 A from a 12 V or 18 V bus, particularly where board area is tight and no compensation network is wanted. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is an external compensation network needed? No. The D-CAP2 loop is closed internally and the data sheet gives the output capacitor and ESR window that keeps it stable. Fitting a much smaller output capacitor than the table asks for is the usual cause of jitter, and fitting a much larger one slows the transient without breaking stability.

Can VCC and VIN come from different rails? Yes, and that is a normal use. VCC needs 4.5 V and VIN needs 2 V, so a 3.3 V bus can be stepped down while the control supply runs from 12 V. The two rails then have to be sequenced so VCC is present, or the part stays off.

What sets the output voltage? A divider from the output to the FB pin against a 0.765 V reference. The divider tolerance adds to the 751 to 779 mV reference window, so a one percent pair gives roughly plus or minus 2.8 percent at the output over temperature.

How much current can the VREG5 pin supply? 70 mA, with the output held between 5.3 V and 5.7 V. That current is dissipated inside the package, so at an 18 V input a full 70 mA load adds about 0.9 W to the thermal budget of the part.

Which reel does production receive? The R suffix is 3000 pieces on a 330 mm reel. RGTT is the 250 piece small reel for prototypes, and RGTRG4 is the same large reel with the green material declaration.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.