Contact Us

TPS54302DDCR

Brand: Texas Instruments
Texas Instruments TPS54302DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54302DDCR — Power Management & Signal Chain | Superb Automation

TPS54302DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54302DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54302DDCR: 4.5 V to 28 V input, 3 A synchronous step-down, 400 kHz, SOT-23-6

TPS54302DDCR is a synchronous step-down converter rated 3 A with the high side and low side switches inside the package and a fixed 400 kHz switching frequency in a SOT-23 body of 6 pins. The 4.5 V to 28 V input covers a 24 V industrial bus with margin for a 10 per cent rise, and the 85 milliohm high side and 40 milliohm low side switches keep the conduction loss low enough that the six pin package can carry 3 A on a real board area. Frequency spread spectrum is built in, which is unusual at this price point.

Order code and package

TPS54302DDCRActive, SOT-23-THIN, 3000 pieces on a large reel, SN finish, MSL-1-260C unlimited floor life, marking 4302
TPS54302DDCTActive, 250 pieces on a small reel, the same body
TPS54302DDCR.A and .BActive rows of the same string, so the reel label alone does not identify which material revision ships
Package size2.9 mm by 2.8 mm including pins, six pin SOT-23 thin
Temperature rangeminus 40 to 125 degrees junction on every published row

Electrical parameters that decide the application

Input voltage4.5 V to 28 V
Output current3 A continuous, with the internal switches integrated
Switch resistance85 milliohm high side, 40 milliohm low side
Switching frequency400 kHz fixed, with frequency spread spectrum for emissions
Soft start5 ms internal, no external capacitor
Shutdown current2 microamp typical
Quiescent current45 microamp typical in no load operation
Protectioncycle by cycle current limit on both switches, hiccup mode, output overvoltage, thermal shutdown

Family variants and how they differ

TPS54302eco-mode pulse skip, the version on this page
Feedback0.8 V internal reference, set by an external divider
EN pinprecision enable, can be used as an undervoltage lockout with two resistors
Bootstrapexternal capacitor from SW to BOOT, no internal bootstrap diode drop
Compensationinternal, so no external network and no COMP pin

Points to check before this part goes on a BOM

Spread spectrum is a real advantage at 400 kHz. A fixed frequency converter puts all its energy at one frequency and its harmonics, which is exactly what a conducted emissions scan looks for. The spread spectrum circuit moves the switching frequency by a few per cent around the centre, smearing the peak. On a 24 V industrial board that can be the difference between passing and needing a second filter stage.

Twenty eight volts is not a 24 V rail with margin for nothing. A 24 V bus that is allowed ten per cent high reaches 26.4 V, and a transient on a vehicle or an industrial supply goes higher still. The 28 V rating covers the bus, not an automotive load dump, which reaches tens of volts above that and needs a separate clamp.

The five millisecond soft start is fixed and it is short. It is enough to stop a 100 microfarad output capacitor from looking like a short at power up. It is not enough to sequence a board with several rails, so the enable pin has to be driven by a supervisor or a sequencer if the order matters.

Hiccup mode is the protection behaviour to understand. When the current limit trips repeatedly the part shuts down, waits, and retries. That keeps the dissipation low during a short, and it also means a hard short shows as a pulsing output rather than a dead one. A test fixture that expects a static output will misread a board in hiccup as working. The retry period is set internally, so a load that draws a heavy inrush current can trip the limit, recover, and trip again in a rhythm that looks like an unstable supply.

The 400 kHz frequency sets the inductor and the capacitor. A higher frequency would allow a smaller inductor, but 400 kHz keeps the switching loss down at 28 V in. The trade is ripple: at 400 kHz and 3 A the inductor has to be larger, and the output capacitor has to handle a ripple current that a 2 MHz part would not produce.

Internal compensation limits the output capacitor range. The loop is closed inside the part and is stable across a range of ceramic output capacitors, but not across every value. A board that replaces a 22 microfarad output capacitor with 220 microfarad to chase ripple will change the loop and can ring on a load step.

The enable pin is a precision input, not a logic pin with a fixed threshold. It is used as an adjustable undervoltage lockout with a divider from the input. That is how a 24 V board avoids starting while the bus is still ramping, which otherwise produces a wrong output and a reset loop in the load.

Thermal performance decides the real current at 28 V in. At 28 V in and 5 V out the duty cycle is short and the low side carries most of the conduction, but the high side switching loss rises with the square of the voltage. Three amps is available in a 24 V to 5 V application on a board with a real copper pour under the part, and less than that on a two layer board with a narrow trace.

The .A and .B suffix rows are a sourcing detail worth flagging. The addendum lists the same ordering string more than once with different material revisions. A customer who files a material declaration against one row and receives another has a documentation problem even when the part is functionally the same, so the offer should state which row ships.

What to confirm before this part goes on a purchase order

State the input bus and the output voltage, not only the part number. The same string is used on 12 V and 24 V boards with different inductors, and a substitute offered without the bus voltage cannot be checked against the ripple and the thermal margin.

Ask for the marking and the date code. The 4302 marking is shared across the .A and .B rows, so the reel label and the packing list are what distinguish them, and for a customer with a material declaration on file that distinction has to appear on the offer.

Where this order code fits

It drops a 24 V industrial bus or a 12 V rail to 5 V or 3.3 V at 3 A, on boards that have to pass emissions with a small input filter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it need an external compensation network? No. The loop is compensated inside the part, which is why there is no COMP pin. The output capacitor still has to be chosen inside the stable range, but there is no network to tune.

Can it run from a 24 V battery without a clamp? The 28 V rating covers a regulated 24 V bus with ten per cent tolerance. A battery rail that can be charged to 29 V or a vehicle rail with load dump needs an external clamp or a part with a higher rating.

What is the minimum load for stable operation? There is no minimum load. In eco-mode the part skips pulses at light load and holds the output, with a slightly higher ripple. If the load is an analogue rail that cannot tolerate the skip ripple, the output capacitor and the inductor have to be chosen for the light load case.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.