Contact Us

TPS54061DRBR

Brand: Texas Instruments
Texas Instruments TPS54061DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54061DRBR — Power Management & Signal Chain | Superb Automation

TPS54061DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54061DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54061DRBR: 200 mA synchronous step-down converter with a 60 V input and a 90 uA quiescent current

TPS54061DRBR is a small synchronous buck converter that survives a 60 V rail and draws 90 uA when it is regulating, built for bias supplies in industrial and metering equipment in a VSON body of 8 pins. The TPS54061 takes 4.7 V to 60 V in and delivers up to 200 mA with both switches integrated, which removes the catch diode that a non-synchronous part in this class would need. Peak current mode control keeps the external parts few and lets the compensation be set with a small network. Operating quiescent current is 90 uA and shutdown current is 1.4 uA, both of which matter on a rail that is present even when the load is asleep. The body is an eight pin 3 mm by 3 mm VSON with an exposed pad.

Order code and package

Order codeTPS54061DRBR
Input voltage4.7 V to 60 V
Output current200 mA
Switchesintegrated high side and low side MOSFETs
Controlpeak current mode
Quiescent current90 uA typical, 110 uA maximum at 12 V in
Shutdown current1.4 uA with the enable pin low
Input start voltage4.5 V typical, rising
Enable to switching450 us
Package8 pin VSON, 3 mm by 3 mm, exposed pad
Frequencyset by an external resistor, with diode emulation at light load
DocumentSLVSBB7E, May 2012, revised November 2015

Electrical parameters that decide the application

Quiescent current conditionmeasured with the feedback pin at 0.9 V and 12 V in
Enable threshold at plus 50 mV-4.7 uA of hysteresis current
Enable threshold at minus 50 mV-1.2 uA of hysteresis current
Junction range-40 C to 150 C
Reference0.8 V class, checked against the electrical table for the exact member
Switch resistancequoted in the electrical table at 12 V in
Thermal paththe exposed pad on the VSON body
Duty cyclelimited by the minimum on time at high input
Light loaddiode emulation holds efficiency up at millamp loads
Input bypassa ceramic capacitor close to the input pin, rated above 60 V
Output capacitorceramic, sized for the ripple at 200 mA
Protectioncycle by cycle current limit and thermal shutdown

Points to check before this part goes on a BOM

Sixty volts is a bus rating, not a suggestion. A 48 V industrial rail with a transient suppressor can reach 55 V during a load dump, and a part rated at 40 V would be damaged even though the steady state looks comfortable. This family is chosen for that margin, and the input capacitor has to be rated for the same transient rather than for the nominal.

Ninety microamps of quiescent current is what allows the converter to stay enabled on a loop powered transmitter. A 4 to 20 mA loop can spare a few milliamps in total for the electronics, so a converter that draws a milliamp of housekeeping would use a large fraction of the budget. The shutdown current of 1.4 uA matters when the transmitter is parked in a low power state.

Diode emulation at light load is the behaviour to understand before measuring efficiency. At millamp loads the low side switch stops conducting in the reverse direction, so the inductor current does not go negative and the part does not waste energy circulating it. The side effect is a discontinuous output ripple at low load, which some measurement circuits will see as noise.

Peak current mode control with an integrated high side switch sets a minimum on time that limits the conversion ratio at high input. A 48 V to 3.3 V rail needs a 7 percent duty cycle, and at a switching frequency high enough to keep the inductor small the on time can fall below the minimum. The practical result is pulse skipping at high input, which is acceptable but changes the ripple.

The 200 mA rating is small enough that the inductor and the output capacitor are cheap, and the whole supply fits in a few tens of square millimetres. A board that needs 500 mA at 3.3 V from a 48 V rail should look at the larger member of the family, because running this part at its limit with a high duty cycle puts the loss where the package cannot pass it.

A 3 mm by 3 mm VSON with an exposed pad is the only thermal path, and at 200 mA the dissipation is small, around 0.15 W at a 48 V input. That is still enough to need copper under the pad: the part placed on a thin trace with no pour will run 20 C hotter than the same part on a proper pad, and at a 70 C ambient inside a sealed enclosure that margin disappears.

Ordering the DRB suffix gives the 3 mm VSON. Boards that were built around a larger package cannot take this part without a stencil change, and the exposed pad has to be soldered with a via array, which is a reflow profile question as much as a footprint question.

Where this order code fits

This order code fits 4 to 20 mA loop powered transmitters, remote sensors, smart meters and industrial modules that sit on a 24 V or 48 V rail and need a few tens of milliamps at 3.3 V or 5 V. The 60 V ceiling covers a 48 V bus and the transients that come with it, which is the reason this family exists. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is the 60 V rating the absolute maximum or the operating range? The operating input range is 4.7 V to 60 V. The absolute maximum is higher, but a board should keep the steady state and the clamped transients inside the operating range.

Does the part need an external diode? No. Both switches are inside the package, which is what separates it from the non-synchronous parts in the same voltage class.

What limits the output current? The 200 mA rating and the cycle by cycle current limit. The loss at 200 mA and a high input voltage is what the package has to carry.

SUPERB supplies this order code with packing and date codes, and the OEM Procurement page sets out what to check when a 48 V bias rail has to be kept in production.