Contact Us

TPS53915RVER

Brand: Texas Instruments
Texas Instruments TPS53915RVER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS53915RVER — Power Management & Signal Chain | Superb Automation

TPS53915RVER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS53915RVER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS53915RVER: 1.5 V to 18 V input, 12 A synchronous buck converter with PMBus

TPS53915RVER is a 12 A point of load converter with D-CAP3 control and a PMBus interface for voltage margining, soft start and fault reporting in a QFN (RVE) body of 28 pins. It delivers 12 A from 13.8 milliohm and 5.9 milliohm FETs, takes 1.5 V to 18 V on the power stage with a 4.5 V to 25 V bias rail, and sets output, frequency and protection behaviour over PMBus instead of resistor straps.

Order code and package

Ordering stringTPS53915RVER, RVE package, 3.5 mm by 4.5 mm 28-pin QFN, tape and reel
Package28-pin QFN, 3.50 mm by 4.50 mm, with exposed pad
Ambient range-40 C to 85 C
BusPMBus, with SDA, SCL and ALERT pins
Bias railVDD from 4.5 V to 25 V, separate from the 1.5 V to 18 V power input
Output range0.6 V to 5.5 V

Electrical parameters that decide the application

Input range1.5 V to 18 V on VIN, 4.5 V to 25 V on VDD
Output current12 A continuous
Switch resistance13.8 milliohm high side, 5.9 milliohm low side
Reference0.6 V with plus or minus 0.5 percent tolerance
FrequencyEight settings from 200 kHz to 1 MHz
Current limitValley limit 10.1 A with a 52.3 kohm TRIP resistor, 7.2 A with 38 kohm
ModesAuto-skip for light load efficiency, forced continuous for tight ripple
Programmable over PMBusOutput voltage and margin, soft start, power-on delay, VDD UVLO, frequency, fault reporting

Points to check before this part goes on a BOM

The valley current limit is the number that decides whether 12 A is available. At 52.3 kohm the valley limit is 10.1 A, and because the limit acts on the low-side valley, the peak inductor current is the valley plus the ripple. With a 0.68 microhenry inductor at 500 kHz and 12 V in, the ripple is about 4.5 A peak to peak, so the peak reaches 12.4 A at a 10 A load. A board that expects a clean 12 A must use the 38 kohm value only if the inductor is large enough, and must check the peak rather than the average.

The separate bias rail is what allows the converter to work from a 1.5 V input. The gate drive comes from VDD, so the power stage can sit on a low voltage rail while the drive stays at 5 V, which is the configuration a DDR or a low voltage point of load supply needs. A board that ties VDD to the 1.5 V input will not start, and that mistake is invisible in a circuit review that only looks at the power path.

PMBus changes what a production line can do without a rework. Output voltage, margin high and low, soft start time and the UVLO threshold are all register values, so a single board can be programmed for 0.9 V or 1.0 V at test, and a margin test can be run from the bus rather than from a bench supply. The trade is that the settings live in firmware, and a board with a failed bus will run at its default output, which has to be safe for the load.

At 12 A the conduction loss is 1.0 W in the low-side FET and 0.4 W in the high side at 25 percent duty, so the thermal pad is carrying well over a watt. The 3.5 mm by 4.5 mm body has a large pad, and the data sheet assumes it is soldered to a copper area with vias. A thermally adequate board reaches 12 A, and a board that treats the pad as a signal ground reaches about 8 A before the thermal shutdown at 155 C starts cycling.

Eight frequency settings from 200 kHz to 1 MHz let the same part serve a small, quiet rail and a compact one. At 200 kHz the inductor is 2.2 microhenry or more and the switching loss is low, at 1 MHz the inductor is 0.47 microhenry and the transient response is faster. Because D-CAP3 is an adaptive on-time control, the frequency selection also affects the ripple and the loop, so a change of frequency is a change of the whole output filter, not a single register tweak.

The 0.5 percent reference is what allows a 0.6 V core rail to meet a tight window without calibration. A 0.6 V output from a 0.6 V reference cannot use a divider, so the accuracy of the rail equals the accuracy of the reference plus the error amplifier offset, which is why this part is used for cores rather than for 3.3 V housekeeping rails where 1 percent is enough.

Where this order code fits

It is used for server, storage and networking point of load rails, for optical and broadband line cards, and for any 12 A rail that has to be margined or monitored from a system bus. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the OEM Procurement page.

Questions buyers ask

Can it run without the PMBus? Yes. The part starts with its default settings and regulates, and the bus is only needed for margining, fault reporting and changing the default output or soft start.

Why does it need two supplies? Because the bias rail drives the internal circuits and the gate drivers, while the power input only carries the conversion current, which is what allows a 1.5 V input rail.

What is the highest output voltage? 5.5 V, set by the feedback range, so a 12 V rail cannot be produced by this part even though the input can take 18 V.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.