Contact Us

TPS53316RGTR

Brand: Texas Instruments
Texas Instruments TPS53316RGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS53316RGTR — Power Management & Signal Chain | Superb Automation

TPS53316RGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS53316RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS53316RGTR: 2.9 V to 6 V input, 5 A synchronous step-down converter with selectable frequency

TPS53316RGTR is a fully integrated 5 A synchronous buck converter for 3.3 V and 5 V rails with a selectable current limit and a selectable switching frequency in a QFN (RGT) body of 16 pins. It takes 2.9 V to 6 V in, holds 5 A out through 22 milliohm of switch resistance, and lets the board choose 750 kHz, 1.1 MHz or 2 MHz so the inductor and the switching loss can be traded against each other.

Order code and package

Ordering stringTPS53316RGTR, RGT package, 3 mm by 3 mm 16-pin QFN, tape and reel
Package16-pin QFN, 3.00 mm by 3.00 mm, with exposed pad
Ambient range-40 C to 85 C
Frequency options750 kHz, 1.1 MHz and 2 MHz, set by a pin
Current limit optionsA 4.5 A setting and a 6.5 A setting, selected by the same pin strap
Output range0.6 V up to 0.8 times the input voltage

Electrical parameters that decide the application

Input range2.9 V to 6 V, with no separate bias rail needed
Output current5 A continuous
Switch resistance22 milliohm at 3.3 V input, 18 milliohm at 5 V input
Reference600 mV nominal, 1 percent over temperature
Peak efficiency96 percent, and above 90 percent down to a 100 mA load
Maximum duty89 percent typical in forced continuous mode, 81 percent in the skip mode
Minimum off time90 ns typical at 1.1 MHz, 160 ns maximum
Soft stop60 ohm output discharge when the enable pin goes low
ProtectionsOver current with hiccup, over voltage, under voltage, over temperature, open-drain power good

Points to check before this part goes on a BOM

The three frequency settings change the inductor and the loss at the same time, so the choice is not cosmetic. At 750 kHz with 5 V in and 1.2 V out the ripple in a 1 microhenry inductor is about 1.2 A, at 2 MHz with the same inductor it is 0.46 A. The 2 MHz setting allows a smaller inductor and a faster loop, and it puts the switching loss up by roughly the ratio of the frequencies, which at 5 A shows as several tenths of a watt in a 3 mm square body.

Two current limit settings exist because the same part has to protect a 3 A load and a 5 A load. The 4.5 A setting is right for a rail that never exceeds 3.5 A, and the 6.5 A setting is needed to reach 5 A with ripple. Choosing the higher setting on a low current rail gives away short circuit protection margin for no benefit, and choosing the lower one on a 5 A rail produces a converter that folds back at 90 percent load.

The skip mode is called auto-skip and it is what produces the 90 percent efficiency at 100 mA. In that mode the converter stops switching for stretches and the output ripple becomes a function of the load and the output capacitor, not of the 750 kHz clock. A rail that feeds an ADC or a radio should be run in forced continuous mode, where the ripple is predictable and the efficiency at light load is lower, and the pin strap for that is the same one that selects the frequency.

At 5 A the conduction loss is 0.55 W through 22 milliohm, and the QFN thermal pad is the only path out. The data sheet describes a 16 component, 200 square millimetre solution, which is a statement about a board with a real copper pad under the part. A pad connected by two thin traces instead of a plane will run the junction far above the ambient the customer measured, and that is the usual cause of a 5 A rail that trips its thermal protection at 3 A.

Maximum duty cycle is 89 percent in continuous mode and 81 percent in skip, which sets the dropout. A 5 V to 0.8 V conversion at 750 kHz needs 16 percent duty and is comfortable, while a 3.3 V to 3.0 V conversion needs 91 percent and is outside the continuous mode limit, so the rail will fall out of regulation before the input reaches the output. Any board that asks for a small step down from a 3.3 V bus has to check this number before it checks efficiency.

Soft stop is a 60 ohm discharge on the output when the enable pin goes low. It empties a 100 microfarad load to 5 percent in about 18 ms, which is slow enough to be gentle and fast enough for a power cycle in a test fixture. On a rail that has to hold its charge, such as a memory backup node, that resistor is a reason to choose a different part rather than a nuisance.

Where this order code fits

It is aimed at 5 V and 3.3 V step-down rails in set top boxes, network appliances, industrial controllers and any board that wants a single-chip 5 A converter with an adjustable frequency and no external compensation. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Does it need a separate bias supply? No. The part runs from the same 2.9 V to 6 V rail it converts, with an internal bootstrap switch for the high-side gate drive.

Can two of them share current? There is no current sharing or droop sharing feature, so paralleling two parts does not divide the load predictably and should not be used to reach 10 A.

What sets the output voltage? An external divider into the feedback pin against the 600 mV reference, so the accuracy of the rail is the reference plus the divider tolerance.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.