Contact Us

TPS43061RTER

Brand: Texas Instruments
Texas Instruments TPS43061RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS43061RTER — Power Management & Signal Chain | Superb Automation

TPS43061RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS43061RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS43061RTER: synchronous boost controller with a 5.5 V gate drive for low gate charge FETs and an integrated bootstrap diode

TPS43061RTER is a current mode boost controller that drives two external FETs from a 4.5 V to 38 V input and regulates an output up to 58 V in a WQFN (RTE) body of 16 pins. It holds a 1.22 V reference within 0.8 per cent over minus 40 to 150 degrees, switches from 50 kHz to 1 MHz on a single timing resistor, senses current either across a shunt or across the inductor resistance, and draws 600 uA while running and 5 uA when shut down. The gate drive is 5.5 V, aimed at FETs with low total gate charge rather than at standard threshold parts.

Order code and package

Ordering stringTPS43061RTER, the 16 pin WQFN with the PowerPAD on a 3000 piece large reel
Part marking43061 on the body
Body16 pin WQFN, 3.00 mm by 3.00 mm, with the exposed pad as the only heat path
MaterialRoHS compliant, nickel palladium gold finish, moisture level 2 with a one year floor life at 260 degrees
SiblingTPS43060 is the same controller with a 7.5 V gate drive for standard threshold FETs, so the two are chosen by the FET and not by the current
Qualificationminus 40 to 150 degrees junction, which is the range the electrical table is specified over
Orderable rowsThe addendum prints plain, .A, .B and G4 rows at the same reel size, so a purchase order only needs the string and the quantity

Electrical parameters that decide the application

Input range4.5 V to 38 V operating with 40 V absolute maximum, and a separate enable comparator so the converter can be held off before the bus is valid
Output rangeUp to 58 V, set by a divider into the 1.22 V reference, with the output current limited by the external FETs and inductor rather than by the chip
Reference1.22 V typical, 1.21 to 1.23 V at 25 degrees, 1.195 to 1.244 V over the full temperature range
Gate drive5.5 V on this member against 7.5 V on the TPS43060, with 1 A of peak drive current and an integrated bootstrap diode that removes one external part
Current senseEither a shunt in the source of the low side FET or a resistor and capacitor across the inductor, with the threshold falling from 73 mV at zero duty to 61 mV at maximum duty
Sense window64 to 82 mV at zero duty cycle and 50 to 72 mV at maximum duty, so the current limit tightens as the duty rises rather than staying flat
Switching frequency50 kHz to 1 MHz on the RT pin, 500 kHz at 115 kOhm and 750 kHz at 75 kOhm, with an external clock option on the same pin
Quiescent current600 uA typical and 800 uA maximum into VIN while switching, 5 uA maximum in shutdown
Soft startAn external capacitor on the SS pin sets the ramp, and the part holds the error amplifier output against it so the output voltage rises at a defined rate
Undervoltage lockoutA dedicated pin with 200 mV of hysteresis, so a bus that dips does not restart the converter on every cycle
Thermal shutdownInternal, with the junction limit below the 150 degree rating so the part protects itself before the specification is exceeded
Thermal pathThe 16 pin QFN pad is the only heat path, and the gate drive losses are inside the chip while the switching losses are in the external FETs

Family variants and how they differ

TPS43060 against TPS43061The gate drive differs, 7.5 V against 5.5 V, and this member also carries the integrated bootstrap diode. A FET with a standard threshold and a large gate charge needs the 43060, while a low gate charge part needs the lower drive and the smaller parts count
Cycle by cycle limitThe current sense threshold is compared every switching cycle and the high side FET is turned off for that cycle, so the limit reacts inside one cycle but does not fold the converter back to a low average current
DCR sensingSensing across the inductor resistance removes the shunt loss but makes the current limit a function of the inductor's copper temperature coefficient. A cold inductor has lower resistance and reaches the threshold at a higher current than a hot one
Hiccup on a hard shortThe controller limits the peak current each cycle, and the output voltage falls until the feedback loop reaches its own limit. Recovery is a soft start rather than a jump, which is what keeps the input current from spiking when the fault clears
Bootstrap diodeIntegrated on this member, so the high side drive is fed from VCC through an internal path. A converter that runs at 100 per cent duty for long periods still needs the refresh cycles the controller inserts
What the part does not includeNo FETs, no inductor, no current shunt and no compensation beyond the internal slope. Everything that carries the power is external, which is why the same controller appears in 5 W and 100 W boost stages

Points to check before this part goes on a BOM

The current sense threshold is not constant. It reads 73 mV typical at zero duty and 61 mV at maximum duty, so a boost stage that runs at high duty on a low input carries a lower current limit than the same stage at light duty.

This member drives 5.5 V into the gate, which is below the threshold rating of many standard FETs. A FET chosen for the 43060 will not necessarily switch cleanly on this part, and the data sheet is explicit that the 5.5 V drive targets low gate charge devices.

The 38 V input rating is an operating figure. On a 24 V automotive bus, load dump reaches far above that unless the vehicle has a central clamp, and the clamp belongs to the system rather than to this controller.

The 1.22 V reference is accurate to 0.8 per cent, but the output divider tolerance sits on top of that. A 28 V rail built from a one per cent divider on top of a one per cent reference is a two per cent rail, not a one per cent one.

The RT pin sets the frequency, and the current sense threshold moves with duty. A converter that is retuned from 250 kHz to 750 kHz changes its duty for the same input and output, and therefore changes the effective current limit as well.

The part has no reverse current protection. On a boost stage the body diode of the high side FET conducts from output to input when the input collapses, and a bus that can be switched off while the output holds charge needs a blocking device or a load switch.

Why the bootstrap diode is worth a row in the table

A high side gate driver in a boost stage needs a supply above the switch node. The usual arrangement is a bootstrap capacitor fed through an external diode from the VCC rail, and that diode has to be fast enough to recover before the next cycle. Putting it inside the controller removes a part, a placement decision and a parasitic loop from the switch node.

It does not remove the bootstrap capacitor. The capacitor still sets how much charge is available for the gate, and it still has to be sized against the gate charge of the FET at the switching frequency used. The diode integration only changes the charging path.

Where this order code fits

Boost stages that have to run from a 12 V or 24 V bus and hold a rail above it, from a 5 V rail that has to feed a GaN power amplifier stage at 28 V, and from an automotive bus that swings through load dump territory. The 58 V output ceiling and the 3 mm by 3 mm body suit a boost stage that sits next to the load rather than at the edge of the board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can this part drive standard threshold FETs? No, the 5.5 V gate drive is meant for low gate charge devices. A standard threshold FET with a large gate charge needs the 7.5 V drive of the TPS43060.

How is the current limit set? By a sense resistor in the low side FET source, or by a resistor and capacitor across the inductor. The threshold is 73 mV typical at zero duty falling to 61 mV at maximum duty, so the limit moves with the operating point.

What sets the switching frequency? A resistor on the RT pin, from 50 kHz to 1 MHz, or an external clock on the same pin. The part synchronises to that clock and the internal oscillator follows it.

Does it need external compensation? It is a current mode controller with internal slope compensation, and the compensation network on the COMP pin sets the loop crossover. The part is not fixed compensation, so the network is part of the application.

What happens if the output is shorted? The peak current is limited every cycle and the output collapses. Recovery goes through the soft start ramp rather than a jump, which keeps the input current from spiking when the short clears.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.