TPS43060RTER
Product Specifications
TPS43060RTER
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS43060RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS43060RTER: 58 V output synchronous boost controller with 7.5 V gate drive
TPS43060RTER is a current mode boost controller that drives two external N channel FETs, one as the switch and one as the synchronous rectifier in a WQFN (RTE) body of 16 pins. It takes 4.5 V to 38 V in and regulates any output up to 58 V, with the switching frequency set by one resistor from 50 kHz to 1 MHz or locked to an external clock. The 7.5 V gate drive suits standard threshold MOSFETs, and the feedback reference is 1.22 V with 0.8 percent accuracy from minus 40 to plus 150 degrees.
Order code and package
| Order code read out | TPS43060 RTE R: controller TPS43060 with 7.5 V gate drive, RTE sixteen pin WQFN, R large tape and reel |
| Package | WQFN (RTE), 16 pins, 3.0 mm by 3.0 mm with a PowerPAD, junction to ambient 65.7 degrees per watt |
| Carrier in the vendor addendum | TPS43060RTER at 3000 pieces on a 330 mm reel; RTET is the 250 piece small reel and RTERG4 is the same large reel with the green material code |
| Moisture level | Level 2, 260 degrees peak reflow, one year floor life |
| Lead finish | Nickel palladium gold, quoted as NIPDAU |
| Temperature grade | Junction minus 40 to plus 150 degrees, storage minus 65 to plus 150 |
| Absolute maximum | 40 V on VIN, EN and the sense pins; 60 V on SW including a 10 ns transient of minus 2 V; 65 V on BOOT and HDRV; 8 V from BOOT to SW |
Electrical parameters that decide the application
| Input range | 4.5 V to 38 V, with the internal undervoltage comparator releasing between 4.1 V and 4.3 V on a rising rail |
| Output range | Up to 58 V, which is the figure that decides whether a 48 V phantom rail or a 36 V LED string is inside the part |
| Reference | 1.22 V typical, 1.21 to 1.23 V at 25 degrees and 1.195 to 1.244 V over the full junction range |
| Gate drive | VCC regulates to 7.5 V on the TPS43060, which is the variant for standard threshold FETs; the TPS43061 regulates to 5.5 V for low gate charge devices |
| Switching frequency | 50 kHz to 1 MHz by resistor, with 450 to 550 kHz at 115 kohm and 675 to 825 kHz at 75 kohm; external synchronisation from 300 kHz to 1 MHz |
| Current sense | 64 to 82 mV maximum threshold at zero duty and 50 to 72 mV at maximum duty, with a 3.8 mV reverse threshold for the synchronous FET |
| Quiescent current | 600 microamp typical and 800 microamp maximum into VIN, and 1.5 to 5 microamp shut down |
| Enable thresholds | Below 1.2 V the part enters standby and below 0.4 V it shuts down, with a 1.8 microamp pull up and 3.2 to 4.6 microamp of hysteresis current |
| Soft start | One capacitor on the SS pin sets the ramp, and the part starts into a pre-biased output without discharging it |
| Protection | Cycle by cycle current limit, thermal shutdown, and an adjustable output overvoltage comparator |
| Sensing options | A resistor in the source of the low side FET or lossless inductor resistance sensing, which is what keeps efficiency high at 10 A and above |
How this controller differs from its neighbours
| TPS43060RTER | 7.5 V gate drive for standard threshold MOSFETs, the version on this page |
| TPS43061 | 5.5 V gate drive for low gate charge NexFET devices, which cuts drive loss at high frequency |
| RTERG4 row | identical part and reel with the green material declaration for customers tracking material content |
| Synchronous rectification | the second gate output replaces a Schottky diode, which is where the efficiency advantage over older boost controllers comes from |
| Synchronous flyback | the same controller drives a flyback stage, which is why it appears in isolated auxiliary rails |
Points to check before this part goes on a BOM
The 7.5 V gate drive is the reason to pick the 60 over the 61 in most builds. A standard threshold FET needs about 6 V to reach its rated on resistance, and a 5.5 V drive leaves it partly enhanced with a higher conduction loss. The 61 exists for low gate charge devices whose maximum gate voltage is lower, and where the switching loss at 1 MHz dominates. The two parts share a pin out, so the choice can be changed late, but the FET has to match the controller rather than the other way round.
The current limit operates on the sense voltage and its threshold falls as duty cycle rises, from 73 mV typical at zero duty to 61 mV at maximum duty. That slope is deliberate: it gives a boost converter a measure of protection against inductor saturation during a start up into a pre-charged output. A board that uses the 73 mV figure for the whole range will find the limit arriving earlier than expected at high duty, which is exactly when the inductor is closest to saturation.
Lossless inductor resistance sensing is worth the extra care it takes. A sense resistor of 1 milliohm at 10 A costs 0.1 W and a little more board space; the inductor's own resistance does the same job for free if the RC network across it is matched to its time constant. The catch is that the sensed value drifts with temperature and the matching network has to be right, so a first prototype is usually built with a resistor and converted to DCR sensing once the current waveform has been seen on a scope.
Soft start into a pre-biased output is a subtle but useful behaviour. In a system where a 24 V rail is boosted to 48 V and the 48 V rail is already held by another source during a restart, a controller that discharges the output before starting will pull the rail down and disturb the load. This part does not, and the SS capacitor sets how gently it takes over. The same behaviour is what makes it usable in a redundant supply arrangement where either converter may start first.
The 150 degree junction rating is what makes the part suitable for an automotive or industrial enclosure. The 65.7 degrees per watt junction to ambient on a four layer board means 1 W of loss is a 66 degree rise, so at 100 degree ambient the part is close to its limit at 1 W. The gate drive loss at 1 MHz with two 20 nanocoulomb FETs is about 0.3 W on its own, which is why the frequency choice and the FET choice are made together rather than one after the other.
Synchronising to an external clock is available between 300 kHz and 1 MHz and locks within 100 to 250 microseconds. In a multi rail system that beats against an audio band or a radio, locking every converter to one clock moves the beat products to a known frequency that can be filtered. The RT/CLK pin detects the presence of a clock and falls back to its resistor setting within 140 to 250 microseconds if the clock stops, so a lost clock does not stop the rail.
Where this order code fits
Used for 12 V to 24 V, 24 V to 48 V and battery to 48 V stages in telecom and industrial equipment, LED string drivers, GaN RF power amplifier bias rails, automotive start stop rails and isolated auxiliary supplies built as a synchronous flyback. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What sets the output voltage? A divider from the output to the FB pin against the 1.22 V reference. The reference is accurate to 0.8 percent over the full junction range, so a one percent divider pair gives about 1.8 percent at the output before any load regulation error.
Can it be synchronised to a system clock? Yes, from 300 kHz to 1 MHz, with a lock in time of 100 to 250 microseconds. If the clock disappears the part returns to its resistor programmed frequency within 140 to 250 microseconds, so the rail keeps running.
Does it need a Schottky diode? No, the second gate output drives a synchronous FET. A diode is sometimes fitted in parallel for the first few switching cycles before the high side device is enhanced, and the data sheet shows where that is worthwhile.
What is the difference from the TPS43061? Only the gate drive voltage: 7.5 V here against 5.5 V there. The 60 suits standard threshold FETs, the 61 suits low gate charge devices at high frequency. The pin out is the same.
How is the current limit adjusted? By the sense element and the sense pins, with a threshold between 50 mV and 82 mV depending on duty cycle. Lossless inductor resistance sensing can replace the resistor if the RC network is matched to the inductor.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.