TPS40170QRGYRQ1
Product Specifications
TPS40170QRGYRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS40170QRGYRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS40170QRGYRQ1: wide input synchronous buck controller from 4.5 V to 60 V with a 600 mV reference
TPS40170QRGYRQ1 is a controller that drives external MOSFETs from a 60 V rail, with voltage mode control, feed forward and low-side current sensing in a VQFN body of 20 pins. The TPS40170 is a synchronous buck controller rather than a converter: the switches are external, which is how it reaches output currents the integrated parts cannot. It runs from 4.5 V to 60 V, holds a 600 mV reference with one percent accuracy, and offers a programmable frequency from 100 kHz to 600 kHz with bidirectional synchronisation between a primary and a secondary controller. Low-side FET sensing provides the overcurrent protection, and the part includes an 8 V and a 3.3 V internal regulator for its own housekeeping and the gate drive.
Order code and package
| Order code | TPS40170QRGYRQ1 |
| Input voltage | 4.5 V to 60 V |
| Reference | 600 mV, one percent accuracy |
| Control | voltage mode with input voltage feed forward |
| Switching frequency | 100 kHz to 600 kHz, programmable |
| Synchronisation | bidirectional, primary and secondary |
| Overcurrent sensing | low-side FET drain to source voltage |
| Internal regulators | 8 V and 3.3 V |
| Shutdown current | 1 uA typical, 2.5 uA maximum |
| Operating current | 4.5 mA with the drivers not switching |
| Package | 20 pin VQFN |
| Maximum duty cycle | 95 percent at 100 kHz, 91 percent at 300 kHz |
| Document | SLUS970C, March 2011, revised November 2023 |
Electrical parameters that decide the application
| Minimum controlled pulse | 100 ns at 4.5 V in, 75 ns at 12 V, 50 ns at 60 V |
| Minimum off time | 170 ns minimum, 250 ns maximum at 12 V |
| UVLO threshold at the pin | 878 mV to 919 mV, 900 mV typical |
| Enable thresholds | 100 mV to disable, 600 mV to enable |
| 8 V regulator | 7.8 V to 8.3 V, 110 mV dropout |
| 3.3 V regulator | 3.22 V to 3.42 V |
| Error amplifier bandwidth | 7 MHz to 13 MHz |
| Soft-start current | 42 uA to 62 uA below 0.5 V, 9.3 uA to 13.9 uA above |
| Thermal shutdown | 155 C to 175 C, 30 C hysteresis |
| Power good thresholds | 527 mV to 570 mV low, 627 mV to 670 mV high |
| Junction range | -40 C to 125 C |
| Bootstrap diode drop | 0.5 V to 0.9 V at 20 mA |
Points to check before this part goes on a BOM
External switches are the reason this part exists. At 48 V in and 12 V out at 20 A, an integrated converter would have to put both switches and their drivers in one package, and the thermal path would not carry it. A controller lets the board use two discrete FETs in a package the size the current needs and a copper area that suits the enclosure.
Low-side sensing is the cheaper overcurrent method and it has a known limitation. It measures the voltage across the low-side FET while that FET is on, so it cannot detect a short from the switch node to ground during the on time of the high side. The part adds a minimum off time and a pulse-by-pulse limit, but a board that needs short circuit protection during the high-side on time should add a separate comparator.
Voltage mode control with feed forward needs a compensation network that matches the output filter, and the values change when the output capacitance changes. A board that substitutes a different capacitor bank, for example from polymer to ceramic, has to recheck the loop, because the resonance moves and the phase margin with it. This is the main difference from an internally compensated converter.
Duty cycle limits are generous at low frequency and tighten as the frequency rises: 95 percent at 100 kHz, 91 percent at 300 kHz and 82 percent at 600 kHz. A 48 V to 12 V conversion needs 25 percent, so there is room, but a 48 V to 3.3 V rail at 600 kHz needs 7 percent and the 50 ns minimum pulse at 60 V then decides whether the loop can hold it.
Two on-chip regulators are easy to overlook. The 8 V rail drives the gate of the high-side FET and the 3.3 V rail runs the housekeeping, and both are available to light external loads. A board that takes current from the 8 V rail has to keep it under the rated output or the gate drive droops and the switching loss rises, which shows up as a thermal problem rather than as a control problem.
Bidirectional synchronisation allows two controllers to run at the same frequency with a defined phase. That is what keeps the input ripple of a two-phase supply from doubling, and it is also what stops two converters on one input from beating at a low frequency. The part offers a 0 degree and a 180 degree secondary option, selected by the voltage on one pin.
The Q1 automotive suffix on a controller means the qualification record follows the part, which is what a customer audit checks. The electrical behaviour is the same as the industrial member, so a board that moves to the automotive flow does not change its components, only its documentation and its temperature evidence.
Where this order code fits
This order code fits 48 V telecom and industrial rails that need 10 A to 30 A at a low voltage, battery backed systems, and automotive 12 V or 24 V buses where the load is beyond an integrated converter. The external switches also allow the board team to trade conduction loss against cost at the current the board actually needs. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the OEM Procurement page.
Questions buyers ask
Does this part include the MOSFETs? No. It is a controller, so the high-side and low-side FETs, the inductor and the compensation network are board components.
What current can it support? The current is set by the external FETs and the thermal path, not by the controller. Boards in this class run from 10 A to 30 A.
Can two of these share one input? Yes, with the synchronisation feature, which locks them to a common frequency with a 0 degree or 180 degree phase relationship.
SUPERB supplies this order code with date codes and packing, and the Component Lead Time Solutions page sets out what an OEM programme should compare when a controller has to be second sourced.