TPS40055PWPR
Product Specifications
TPS40055PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS40055PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS40055PWPR: wide input synchronous buck controller from 8 V to 40 V with voltage feed forward
TPS40055PWPR is a voltage mode controller with input voltage feed forward, programmable to 1 MHz, that drives external MOSFETs from an 8 V to 40 V rail in a HTSSOP body of 16 pins. The TPS40055 runs from 8 V to 40 V and drives external N-channel MOSFETs with integrated gate drivers in a 16 pin PowerPAD package. Input voltage feed forward keeps the loop gain constant as the input moves, which is what makes the compensation independent of the bus voltage. The reference is 0.7 V with better than one percent accuracy, the frequency is programmable up to 1 MHz, and the part offers soft start, programmable UVLO, programmable high-side current limit and synchronisation to an external clock.
Order code and package
| Order code | TPS40055PWPR |
| Input voltage | 8 V to 40 V |
| Reference | 0.7 V, better than one percent |
| Control | voltage mode with input voltage feed forward |
| Switching frequency | programmable, up to 1 MHz |
| Gate drive | integrated drivers for external N-channel MOSFETs |
| Maximum duty cycle | 94 percent up to 500 kHz, 85 percent above |
| Housekeeping regulators | 5 V and 10 V bias outputs |
| Package | 16 pin HTSSOP with a PowerPAD |
| Synchronisation | external clock accepted |
| Soft start | programmable by capacitor |
| Document | TPS4005x family data sheet |
Electrical parameters that decide the application
| Quiescent current | 1.5 mA typical, 3 mA maximum with the drivers not switching |
| Oscillator accuracy | 470 kHz to 570 kHz at a 500 kHz setting |
| Reference over temperature | 0.693 V to 0.715 V from -40 C to 85 C |
| Error amplifier bandwidth | 3 MHz to 5 MHz |
| Gate drive current | 2 A source and sink minimum |
| Soft-start current | 1.65 uA to 2.95 uA |
| Soft-start clamp | 3.7 V |
| Feed forward voltage | 3.35 V to 3.65 V, 3.48 V typical |
| Thermal resistance | 2 C per W junction to case through the PowerPAD |
| Ambient range | -40 C to 85 C |
| Bootstrap | external diode and capacitor for the high-side drive |
| Current limit | programmable high-side sensing |
Points to check before this part goes on a BOM
Feed forward is the feature that separates this controller from a plain voltage mode part. By scaling the ramp with the input voltage, the loop gain stays constant as the bus moves from 8 V to 40 V, so one compensation network covers the whole range. Without it, the same board would need a different network at each end of the input range, and a bus that moves during operation would move the loop with it.
The 2 C per W junction to case figure belongs to the PowerPAD and to nothing else. It is the best thermal path in this group, and it is what allows the part to sit in a 16 pin HTSSOP and still deliver 2 A of gate drive at 1 MHz. The pad has to be soldered to a copper area with vias, and the copper is what actually dissipates the heat.
Maximum duty cycle falls above 500 kHz, from 94 percent to 85 percent. A 12 V to 5 V conversion needs 42 percent, so the limit is not a constraint there; a 12 V to 10 V rail needs 83 percent and would sit right at the boundary above 500 kHz. The part needs the off time to refresh the bootstrap, which is why the limit exists.
Two bias outputs, 5 V and 10 V, are available for external use and for the gate drive. The 10 V rail is the one that drives the high-side FET in most builds, and its current budget has to cover the gate charge at the switching frequency. A board that adds an external load to that rail can starve the gate drive at high frequency, which appears as slow edges and extra loss.
Programmable high-side current limit is more flexible and less accurate than the low-side sensing used on newer controllers. It measures the drop across the high-side FET during the on time, so it is affected by that FET's temperature coefficient. A limit set for a room temperature measurement will move at 100 C, and the margin has to cover that movement.
Oscillator accuracy of about 10 percent means the switching frequency is a nominal value rather than a guarantee. On a board that needs a precise frequency, for example to place the harmonics between measurement bands, the part can be synchronised to an external clock instead, which removes the tolerance from the oscillator and puts it on the source.
The 1.5 mA quiescent current is high against a modern integrated converter, and it does not matter here. A controller driving 20 A at 1.2 V is not used in a standby rail, and the bias current is a small fraction of the gate drive power. Boards that need a low standby current use a separate small converter for the housekeeping rail.
Where this order code fits
This order code fits 12 V, 24 V and 28 V industrial and telecom rails that need 10 A to 20 A at a low voltage, where the input moves over a wide range and the loop has to stay stable across it. Base station power, industrial computing and instrumentation racks are the usual sockets. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the OEM Procurement page.
Questions buyers ask
What does feed forward do? It scales the PWM ramp with the input voltage so the loop gain stays constant across the 8 V to 40 V range, which lets one compensation network cover the whole range.
Does the part include the MOSFETs? No. It drives external N-channel devices and needs a bootstrap diode and capacitor for the high side.
Why does the maximum duty cycle drop above 500 kHz? The controller needs a minimum off time to refresh the bootstrap supply, and at higher frequency that minimum takes a larger share of the period.
SUPERB supplies this order code with packing and date codes on the offer, and the Strategic Sourcing page sets out how to compare controllers across vendors for a long running programme.