TPS3840DL28DBVR
Product Specifications
TPS3840DL28DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3840DL28DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3840DL28DBVR nano power supervisor for a 2.8 V threshold
The TPS3840DL28DBVR is the 2.8 V option in the same nano power family as the 2.4 V member, in the same 5 pin SOT-23, with the same 300 nA typical supply current and the same open drain active low output. It watches a rail and holds the reset low until the rail has been above 2.8 V plus the hysteresis for the delay set on the CT pin.
The 400 mV step between this option and the 2.4 V one is the whole reason the family exists in 0.1 V increments. A 3 V rail that must not run below its own tolerance needs the 2.8 V threshold, where a two cell pack that must not be over discharged needs the 2.4 V one, and neither board can substitute the other part without changing when the reset asserts.
Key parameters taken from the TPS3840 document
| Threshold | 2.8 V nominal from the 1.6 V to 4.9 V table, printed with 1 per cent typical and 1.5 per cent maximum accuracy over temperature |
| Hysteresis | 100 mV, because a 2.8 V threshold sits inside the 1.6 V to 3.0 V band, so the release point is about 2.9 V |
| Supply range | 1.5 V to 10 V directly, and higher rails through an external divider |
| Supply current | 300 nA typical and 700 nA maximum |
| Start up delay | 220 microseconds typical and 350 microseconds maximum before the reset releases on a supply that has just come up |
| Programmable delay | 50 microseconds with CT open, 6.2 milliseconds at 10 nF, 619 milliseconds at 1 microfarad, 6.2 seconds at 10 microfarad |
| Detection speed | 15 microseconds typical and 30 microseconds maximum from the threshold crossing to the output |
| Glitch immunity | 10 microseconds at 5 per cent overdrive |
| Output | Open drain active low, pull up required, and the reset net must be pulled to a rail that survives the fault |
| Manual reset | Pin 4, asserted by a logic low, left floating when unused |
| Body and reel | SOT-23 5 pin DBV, 3000 pieces on a large reel, body marking DL28 |
| Temperature and handling | Minus 40 to plus 125 degrees C, moisture level 1 at 260 degrees with unlimited floor life |
The threshold and the hysteresis together set two numbers that matter more than either alone. The reset asserts when the rail crosses 2.8 V on the way down, and it releases when the rail has come back above about 2.9 V and the delay has run. On a 3 V rail that means the part reports a rail that has left its own 5 per cent window, and it does not release until the rail is back inside that window, which is the behaviour a processor needs.
Where the numbers matter in a real build
A 3 V rail is common on boards that run from two alkaline cells or from a regulated 3 V rail, and the 2.8 V threshold sits close enough to the bottom of the tolerance band that the choice of option is a judgement about how much margin the load needs. A processor that runs down to 2.7 V can use this part, one that runs down to 2.5 V should use the 2.4 V option, and a board that uses the wrong one will either reset early on a good rail or fail to reset before the processor loses its own margin.
The 220 microsecond start up delay is short and deliberate. A rail that rises through the threshold releases the reset 220 microseconds later, before the rest of the system has powered up, which is what lets a downstream device be held off in an orderly way rather than starting into an undefined rail. Where a longer hold is needed, the capacitor on CT extends that delay to as much as 6.2 seconds, and that number is the one to use when a second regulator needs a second to settle.
The open drain output has a consequence that is easy to miss on a 3 V board. The pull up has to go to a rail that is present while the monitored rail is low, so on a board where the 3 V rail is the only rail, the pull up has to go to the input supply through a resistor that is allowed to conduct into the reset net during the fault. That is normal, but it means the pull up value has to be chosen against the leakage of the processor reset pin rather than against convenience.
What to check before a purchase order is released
- The threshold option against the load, because a 2.8 V part on a processor that needs 2.5 V resets the board while it could still run.
- The pull up rail on the reset net, which has to survive the fault being reported.
- The CT capacitor, since the delay is added to the start up delay and not to the total time the board is held.
- The output type letter, because the push pull member in the same body needs no pull up and behaves differently on a shared net.
- The divider pair if the monitored rail is above 10 V, where the divider tolerance adds to the 1.5 per cent of the part.
Which projects this part fits
Boards running from two alkaline cells, regulated 3 V industrial modules, metering front ends and portable instruments are the natural cases. Any board that already carries the 2.4 V member and needs one more rail watched with the same current budget is the other, because the two parts share a body, a pinout and a resistor free arrangement apart from the pull up.
Questions that come up before a purchase order is released
How much current does the reset net draw?
The open drain output sinks current when asserted and the pull up sets the level, so the standing current is the supply divided by the pull up value, which is the number to add to the 300 nA of the part itself.
Can the threshold be adjusted on the board?
Only downwards in effect by dividing the rail before the supply pin, which also divides the supply the part runs from. The threshold is intended to be used as printed.
Does the part work on a 1.8 V rail?
It works, in the sense that the supply range covers it, but a 2.8 V threshold on a 1.8 V rail would hold the reset asserted permanently, so a lower option is required.
How SUPERB handles this line
This family is bought in reels because the parts are small and the price is low, and the question is usually whether a partial reel with a known date code is acceptable for a build. Our one stop BOM sourcing covers the whole board rather than the supervisor alone, and the incoming inspection plan sets out what is checked on an analogue reel before it is issued to the line. Where a customer needs the part against a fixed schedule, the lead time note explains how a buffer is arranged.