TPS3824-33QDBVRQ1
Product Specifications
TPS3824-33QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3824-33QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3824-33QDBVRQ1: 3.3 V supply voltage monitor with watchdog timer, SOT-23-5
TPS3824-33QDBVRQ1 is a fixed 3.3 V supply supervisor with a watchdog and both reset polarities in one body in a SOT-23 body of 5 pins. RESET asserts when the supply rises above 1.1 V and stays asserted until the rail is above the threshold plus hysteresis, then a fixed 200 ms delay holds the processor in reset long enough for the clock to settle. If the firmware stops toggling the watchdog input the same reset is asserted again, which is the part of the job a simple comparator cannot do.
Order code and package
| TPS3824-33DBVR | Active, SOT-23-5, 3000 pieces on a large reel, minus 40 to 85 degrees |
| TPS3824-33DBVRG4 | Active, Green material declaration, same body and reel |
| TPS3824-33DBVT | Obsolete, small reel, do not specify on a new bill of material |
| The Q1 automotive suffix | no Q1 row appears in this addendum, every row printed is a plain TPS3824 string |
| Threshold options in the family | 2.5 V, 3 V, 3.3 V and 5 V |
Electrical parameters that decide the application
| Supervised rail | 3.3 V on this string, threshold set internally |
| Reset delay | 200 ms fixed on TPS3823, 3824, 3825 and 3828, 25 ms on TPS3820 |
| Watchdog timeout | 1.6 s on TPS3823, 3824 and 3828, 200 ms on TPS3820 |
| Supply current | 15 microamp typical |
| Reset outputs | active-low and active-high both available on this member |
| Manual reset input | not fitted on TPS3824, it belongs to the 3820, 3823, 3825 and 3828 |
| Operating temperature | minus 40 to 85 degrees, or 125 on the TPS3823A-33 |
Family variants and how they differ
| TPS3820 | 25 ms reset delay and a 200 ms watchdog |
| TPS3823 | manual reset input, 200 ms delay, 1.6 s watchdog |
| TPS3824 | both reset polarities out of one body, no manual reset, this order code |
| TPS3825 | adds the manual reset to the dual polarity output |
| TPS3828 | open drain reset output instead of push-pull |
Points to check before this part goes on a BOM
Both polarities in one body is the reason to pick this member. Many processors take an active-low reset and many peripherals take an active-high enable. Having both out of the same five pin part removes an inverter from the bill of material and removes the timing skew between two separate supervisors. The trade is that there is no manual reset pin on this member.
1.1 V is where the reset starts to be meaningful. Below that the output is not guaranteed, so a processor that can start executing at 0.9 V needs a different arrangement. In practice the reset output has to be valid before the processor's own power on reset releases, and on a 3.3 V rail that is easy. On a 1.2 V core rail it is not, which is why the supervisor usually watches the higher rail.
The watchdog timeout is 1.6 s and the firmware has to fit inside it. That is a generous window for a main loop and far too long to catch a lock up inside a control task. Where the loop has to be supervised tightly, the watchdog input is driven from the task itself rather than from a timer, so a stopped task produces a reset instead of a quiet 1.6 s of wrong output.
The watchdog input must be driven, not left floating. The data sheet is explicit that the input has to be driven low or high for a watchdog error to be asserted. On a board where the supervisor is fitted but the firmware does not toggle the pin, the watchdog contribution is nothing and the part is only a reset generator. That is a common outcome when a supervisor is added late in a project.
This addendum prints no Q1 row. The catalogue string ends in QDBVRQ1, which is the automotive qualification suffix, but the orderable rows in this document are the plain TPS3824 strings at minus 40 to 85 degrees. An automotive customer needs the Q1 document and the Q1 rows, so the lifecycle status and the temperature grade of the Q1 string have to be confirmed before a quote goes out.
The 85 degree limit is tighter than the parts around it. A supervisor sitting next to a 125 degree processor is often the item that fails the temperature review, because the supervisor was chosen for its threshold and not for its grade. If the board has to run above 85 degrees ambient, the TPS3823A-33 variant is the one rated to 125.
15 microamp is low enough to stay on a battery rail. The supervisor runs continuously, so its supply current is a permanent drain. At 15 microamp it costs about 130 milliamp hours a year, which on a lithium cell is acceptable and on a coin cell is not. A coin cell arrangement has to switch the supervisor or accept that it sets the shelf life.
Fixed threshold means fixed accuracy, and that is a feature. An external divider adds two resistors and their tolerance to the threshold. The internal divider is trimmed, so the 3.3 V part trips where the vendor says it trips. Where a non standard rail has to be supervised, the 3.3 V part on a divider is the wrong answer and an adjustable supervisor is the right one.
The reset delay is fixed at 200 ms and it cannot be shortened. A processor with a fast oscillator and no external memory may only need a few millisecond, and 200 ms is added to every power up and to every watchdog reset. On a device that wakes many times an hour that delay is visible to the user. The 25 ms member, the TPS3820, is the alternative, at the cost of a shorter watchdog timeout.
The watchdog input has a second job as a boot check. Driving the pin from a firmware task rather than from a hardware timer means the supervisor also confirms that the scheduler is running. Where one task can starve the others, that is the cheapest way to catch it, and it costs one output pin and a toggling line inside the task loop.
What a supervisor has to do that a comparator does not
Hold the reset for a fixed delay after the rail is valid, so the oscillator and the memory have time to settle before the processor fetches its first instruction.
Assert the same reset when the firmware stops running, which turns a silent lock up into a restart instead of a field return.
Where this order code fits
It supervises a processor or DSP reset on industrial and automotive boards, where the watchdog has to catch a firmware loop that stopped toggling. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Is the reset output push-pull or open drain? Both polarities on this member are push-pull. The open drain version is the TPS3828, which is the one to use when the reset has to be wired or with another supervisor or pulled to a different rail.
What happens if the watchdog pin is never toggled? The reset is asserted after the 1.6 s timeout and stays asserted, which holds the processor in reset permanently. Firmware that does not use the watchdog has to drive the pin, or the part must be replaced with a plain reset generator.
Can it supervise a 5 V rail with the same part? No. The threshold is fixed internally per voltage option, so a 5 V rail needs the 5 V member of the family. The bodies and the pinout are the same, which makes substitution easy to get wrong on a mixed board.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.