TPS3760A012DYYR
Product Specifications
TPS3760A012DYYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3760A012DYYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3760A012DYYR: the adjustable 800 mV window supervisor in a 14-pin SOT-23
TPS3760A012DYYR is a wide input window supervisor from the TPS3760 family, the variant that brings the 800 mV threshold out to the SENSE pin so an external divider sets the trip point. It monitors one rail for undervoltage or overvoltage, holds a reset output asserted while the rail is outside the window, and releases it after a delay that is set by a capacitor. The body is a 14-pin SOT-23-THIN measuring 4.1 mm by 1.9 mm, which is small enough to sit next to the connector that brings the monitored rail onto the board.
The family exists because supervisors that run from the rail they monitor stop working when the rail collapses. The TPS3760 separates VDD from SENSE, so the supply can come from a 12 V or 24 V bus while the SENSE pin watches a lower rail, or a higher one, through a divider. Both pins are graded to 65 V, and the supply range starts at 2.7 V, so the same part covers a 3.3 V logic rail and a 48 V industrial bus without a second device.
The numbers below come from SBVS420A, revised September 2023, and from the machinery in section 9 of that document, which works a 12 V example with this exact order code.
What the order code sits on
| Function | window supervisor with separate sense input and programmable delays |
| Supply range | 2.7 V to 65 V on VDD |
| Sense and reset rating | 65 V graded pins, independent of the VDD level |
| Quiescent current | 1 microamp typical |
| Threshold accuracy | 1.5 percent maximum across 2.7 V to 36 V, 1 percent maximum on the 800 mV option |
| Hysteresis options | 2 percent to 13 percent in 1 percent steps, plus fixed values below 8 V |
| Reset delay | 10 nF gives 12.8 ms, 10 microfarads gives 12.8 s |
| Sense delay | 10 nF gives 1.28 ms, 10 microfarads gives 1.28 s |
| Output topology | open drain or push pull, active low or active high, fixed by the order code |
| Manual reset | CTR pin, pulls the output asserted when driven low |
| Latch option | CTS pin becomes a latch input on latch capable variants |
| Package | SOT-23-THIN, 14 pins, 4.1 mm by 1.9 mm |
| Temperature range | minus 40 to plus 125 degrees ambient |
| Reel | 3000 pieces on a large reel, moisture level 1 |
| Part marking | A012 |
Reading the suffix, and the worked example the vendor prints
The order code packs four choices into a few characters, and TI uses this exact string in its own example, which makes the decode unusually concrete. Across the family the fields carry the sensing logic, the reset topology, the reset polarity, the threshold option and the hysteresis option, and the last character before the package code selects the hysteresis. On this string the hysteresis is 2 percent, the threshold is the 800 mV adjustable variant, and the sense input is the undervoltage side of the window.
The example in the document is a 12 V rail monitored for undervoltage at 90 percent, which is 10.8 V. With a 10 k bottom resistor the calculation gives 125 k for the top resistor, and because the hysteresis adds 2 percent on top of the 800 mV threshold, the reset releases when the monitored node comes back above 11.016 V. That gap between the trip point and the release point is the whole reason a supervisor exists: a rail that dips to 10.8 V and recovers to 10.9 V would otherwise chatter the reset line for as long as the dip lasts.
The 800 mV variant bypasses the internal divider, which is why it is the one TI recommends whenever an external divider is used. The internal ladder on the fixed variants is trimmed for a specific rail and its impedance is part of the error budget; on this variant the SENSE pin presents a high impedance and the divider is entirely the customer's. The document still warns that the pin has a finite resistance that has to be accounted for when the divider values are large, and gives the means to calculate it.
Delays, debounce and the latch input
Two capacitors set the timing, and they are not interchangeable. CTS sets the sense delay, the time between the SENSE pin crossing the threshold and the reset output asserting, and it also acts as a debouncer that ignores short glitches on the monitored rail. CTR sets the reset delay, the time the output stays asserted after the rail returns to the valid window. The scaling is fixed: 10 nF on the reset pin gives 12.8 ms and 10 microfarads gives 12.8 s, while the same capacitors on the sense pin give 1.28 ms and 1.28 s, a factor of ten apart.
On latch capable variants the CTS pin changes meaning. Latch mode holds the reset asserted after the fault clears, which is what a system wants when a transient should stop the machine until an operator acknowledges it, and the pin is then driven rather than fitted with a capacitor. The document specifies the levels that enter and exit latch mode and recommends a pull-down on the pin, so a board that mixes the two functions has to be checked against the variant actually bought.
The CTR pin doubles as a manual reset input on the parts that do not use it for a capacitor. Driving it low forces the output asserted, which gives a front panel reset button without extra logic, but the pin must not be driven high. A board that puts a push button and a timing capacitor on the same node is fighting the two functions against each other, and the capacitor discharge through the button is the usual symptom.
Where the 65 V rating earns its place
Industrial racks, motor drives and building controllers often carry a 24 V bus with transients well above the nominal, and a supervisor hung directly on that bus has to survive them without a series resistor and a clamp. The 65 V VDD and SENSE ratings let the part sit on the bus, and the 2.7 V floor lets the same device keep working while the bus collapses during a power failure, which is when the reset has to be asserted and held.
The low quiescent current matters for the same reason in reverse. A supervisor that draws 1 microamp typical can stay powered from a small standby rail while the rest of the system is off, and it can hold a processor in reset without adding a load that drains the standby supply. On a battery backed instrument this is the difference between a supervisor that is always on and one that is only powered after the main converter comes up, and the second arrangement cannot guard the start-up sequence.
The split between VDD and SENSE also allows redundancy that a single-pin device cannot offer. The SENSE pin can watch a rail through a divider while VDD is taken from a protected auxiliary supply, so a fault on the monitored rail does not remove the supply that is supposed to report it. The document describes this arrangement as the reason for the separate pins, and it appears in functional safety discussions where the supervisor is part of the diagnostic coverage.
Carriers and what the addendum prints
| TPS3760A012DYYR | SOT-23-THIN DYY, 14 pins, 3000 pieces on a large reel, active |
| TPS3760A012DYYR.A | same body and reel, the .A row of the same string |
| Lead finish | NIPDAU |
| Moisture level | Level-1-260C-UNLIM, unlimited floor life |
| Operating temperature | minus 40 to plus 125 degrees |
| Sibling strings | A015, E012, E565 in the same 14-pin body |
| Small reel | not published for this string, the addendum lists 3000 only |
| Carrier | large tape and reel, 336.6 mm box dimension per the addendum table |
Level 1 with unlimited floor life is convenient on a mixed line, because the reel does not expire on the shelf and there is no bake step before reflow. That is not the case for every supervisor in this class, and a customer audit that asks for the moisture record will find this row clean.
The addendum lists only the 3000 piece reel for this string, so a prototype build has to take a partial reel or a distributor cut. That is worth saying up front, because a buyer comparing this part with a competitor sometimes assumes a 250 piece option exists across the family and finds out at the quotation stage that it does not.
Choosing between this part and a fixed threshold device
The adjustable variant is the right choice when the monitored rail is not one of the values in the vendor table, when the trip point has to sit at a percentage of a rail that is set by another component, or when the divider is already on the board for another reason. It is the wrong choice when the rail is a standard 3.3 V or 5 V and nothing else on the board needs the divider, because two resistors and their tolerances add error that a fixed variant does not have.
When a customer is replacing an older supervisor, the comparison is rarely about the threshold alone. The release delay, the output topology and the polarity have to match the processor's reset input, and the hysteresis has to be wide enough to cover the ripple on the monitored rail. A part with the right threshold and the wrong output topology will hold a processor in reset forever or never assert at all, which is why the cross reference work starts from the pin functions. Our power management cross reference page covers the comparison order, and the component lead time solutions page covers the case where the correct part is quoted at twenty weeks.
Questions buyers ask before a first order
Can the same part monitor overvoltage instead of undervoltage? Not this string. The sense logic is fixed by the order code, and the overvoltage variants carry a different character in that field. A window that has to guard both ends needs two devices or a different family member.
What sets the reset delay if the capacitor is omitted? The pin left floating gives the shortest delay the device offers. The exact figure is in the timing table of SBVS420A, and it is short enough that a processor with a slow supply ramp may need the capacitor fitted.
Does the output need a pull-up? Only on the open drain variants, where an external resistor to the logic rail is required. The push-pull variants must not have one, because the output would fight the pull-up when it drives low.
Is the part functional safety capable? TI lists it as functional safety capable with documentation available to aid a safety system, which means the FIT data and the failure mode information can be requested. It is not a certified element on its own.