Contact Us

TPS2829DBVR

Brand: Texas Instruments
Texas Instruments TPS2829DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2829DBVR — Power Management & Signal Chain | Superb Automation

TPS2829DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2829DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2829DBVR single channel MOSFET driver with no internal regulator

The TPS2829DBVR is a single channel high speed MOSFET driver in a five pin SOT-23. It delivers 2 A peak, switches in 25 nanoseconds with a 40 nanosecond propagation delay at a 1 nF load, and runs from a 4 V to 14 V supply. Its defining feature is what it does not have: the internal regulator that the TPS2816 to TPS2819 members carry is omitted, which drops the quiescent current to below 15 microamp and removes the regulator dissipation from the package.

That omission is the reason the part exists. On a card where the gate drive rail is already regulated at 10 V or 12 V, the internal regulator of the larger members does nothing but turn the difference between the input rail and the gate level into heat. The 2828 and 2829 remove it, and a driver that would otherwise need a thermal calculation becomes a part that can sit in a small package next to the FET.

Key parameters taken from the TPS2816 to TPS2829 document

ChannelsOne
Peak output current2 A
Rise and fall25 nanoseconds maximum into a 1 nF load
Propagation delay40 nanoseconds maximum
Typical edges14 nanoseconds typical rise and fall, from the document description
Supply range4 V to 14 V, with no internal regulator on this member
Quiescent currentBelow 15 microamp with the input high or low
Input thresholdsTypically two thirds and one third of the supply
Shoot throughHeld low by the output stage, which is the basis of the low supply current
Latch-upListed as highly resistant in the document
TemperatureMinus 40 to plus 125 degrees ambient
PackageSOT-23, five pins, DBV suffix; the fourth pin is not connected on this member
Family fitThe TPS2818 and TPS2819 are the same driver with the regulator fitted but without the active pull-up of the 2816 and 2817
Order code noteDBV is the five pin SOT-23 body, R is the reel tape

The figures are read from the vendor document. The electrical characteristics section prints them with a 10 V supply and a 1 nF load, which is the condition a bench check has to reproduce before a substitution is accepted.

Where the numbers matter in a real build

Fifteen microamp of quiescent current is what makes this part usable on a card that has to meet a standby power budget. A driver with a regulator inside draws milliamps even when nothing is switching, and on a product that sits in standby for most of its life that current is the difference between a compliant and a non compliant card. The same omission removes the regulator's heat, so the package stays cool at switching frequencies where the larger members need derating.

The downside is that the gate drive level is now the supply level, so a 4 V to 14 V rail decides the gate voltage directly. A logic level FET driven from a 5 V rail works, and a standard FET that wants 10 V does not. This is the trade a card makes when it drops the regulator: it has to supply a regulated gate rail of its own, usually from a small linear or a charge pump.

The input threshold at two thirds of the supply is the third practical point. At a 12 V supply the positive threshold is around 8 V, so a 3.3 V controller cannot drive this part directly. A level shift is needed, and on a card that already has one for another device it costs nothing, while on a card that does not it is an extra stage that has to be added before the driver is usable.

  • The gate rail, since the supply is the gate voltage on this member and there is no regulator to hold it.
  • The standby current budget, which is the reason to choose this part over the regulated members.
  • The input threshold against the controller swing at the chosen supply.
  • The five pin body and the unconnected pin, which must be left floating rather than tied to a rail.
  • The gate loop inductance, since 2 A in 25 nanoseconds is the same problem here as on any driver.
  • The date code, because the document revision dates from the 2000s and the part is still purchased against old drawings.

Which projects this part fits

The document lists the family as a low cost single channel driver for power supplies, motor drives, lamp ballasts and telecom cards. The 2829 suits boards with a regulated gate rail and a standby power target, where a separate regulator inside the driver would be wasted.

Questions that come up before a purchase order is released

What is missing compared with the TPS2818?

The internal regulator. The 2818 has it, the 2829 does not, and the quiescent current falls from the milliamp range to below 15 microamp as a result.

Can it drive a standard gate MOSFET from 12 V?

Yes, when the 12 V rail is the gate supply. The part passes the rail to the gate, so a 12 V rail gives a 12 V gate, which is inside the gate rating of most standard devices.

Does the unconnected pin need a pad on the board?

The pin is not connected internally on this member. Leaving the pad unconnected is correct, and tying it to a rail is not.

Is the input compatible with a 3.3 V controller?

At a 5 V supply the threshold is around 3.3 V, so the margin is small. At a higher supply the controller needs a level shift.

How SUPERB handles this line

Small drivers on long life boards are bought years after the drawing was released, which makes the revision and the date code part of the order rather than a detail. Our obsolete part cross reference hub covers this family against its alternatives, the lead time solutions page covers a bridging buy, and how to reduce component cost describes what a change of package or reel size does to the unit price.