TPS259481AYWPR
Product Specifications
TPS259481AYWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS259481AYWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS259481AYWPR 8 A eFuse with reverse blocking control and auto-retry
The TPS259481AYWPR is the member of the TPS25948 family that carries the reverse blocking control pin. It runs from 3.5 V to 23 V, holds a typical 12.2 milliohm path, is rated for 8 A, and sits in a 12 ball power wafer scale package of 2.43 mm by 1.71 mm. The A suffix is auto-retry, so a fault that clears lets the part start again by itself after a fixed delay.
The pin that earns this part its place is RCBCTRL. With reverse blocking active the part behaves like an ideal diode and refuses current from output back to input. With the pin asserted the blocking is released and power can flow in either direction in steady state, which is what a USB dual role port or an on the go port needs. That single function is the reason a board cannot simply substitute the 480 member for this one, even though the two share a body, a reel and most of the electrical table.
Key parameters taken from the TPS25948 document
| Input range | 3.5 V to 23 V operating, 28 V absolute maximum |
| Supply source | Can be powered from either IN or OUT |
| On resistance | 12.2 milliohm typical for the integrated back to back pair |
| Reverse control | RCBCTRL pin disables reverse blocking and allows bi-directional delivery in steady state |
| Current limit window | 1 A to 9 A, ten per cent accuracy above 3 A |
| Limit setting | One resistor on the ILM pin, printed as 4834 divided by the limit in amps |
| Published limit points | 2.43 k for 2.25 A, 1.62 k for 3.3 A, 604 ohm for 8.7 A |
| Fast trip | Under one microsecond typical, threshold tied to twice the set limit |
| Overvoltage lockout | Adjustable with a divider, one microsecond typical response |
| Blanking timer | Capacitor on ITIMER, so a peak above the limit passes for a bounded time |
| Current monitor | Analog output on the ILM pin, six per cent typical accuracy above 3 A |
| Surge | IEC 61000-4-5 tested to 28 V on the input |
| Package | PowerWCSP YWP, 12 balls, 2.43 mm by 1.71 mm, 0.5 mm pitch |
| Carrier | 3000 pieces on a large reel, moisture level 1 at 260 degrees with unlimited floor life |
| Marking and grade | 259481A, rated minus 40 to plus 125 degrees junction |
All rows come from the vendor document, and the two rows that decide a purchase are the reverse control row and the marking row, because neither is visible on a board after assembly.
Where the numbers matter in a real build
Releasing reverse blocking is not the same as removing the protection. When RCBCTRL is asserted the two FETs stay on and the part becomes a low resistance path in both directions, so the current limit, the overvoltage lockout and the thermal protection still apply. What changes is the direction of the current that those protections see. In a dual role port the same connector can be a sink and a source, and the pin is switched by the port controller when the role changes, so the timing of that switch is part of the system behaviour rather than part of the eFuse.
The 12.2 milliohm path is what makes bi-directional operation practical. A discrete back to back pair of FETs with the same resistance needs two packages, two gate drives and a charge pump, and the wafer scale part puts all of it in 4.2 square millimetres. At 8 A the pair dissipates about 0.8 W, and in reverse the same figure applies, so a port that delivers 8 A to an external device has the same thermal budget as one that takes 8 A in.
The current limit equation is 4834 divided by the limit in amps, with the published points at 604 ohm for 8.7 A, 1.62 k for 3.3 A and 2.43 k for 2.25 A. For a dual role port the limit has to be set above the highest current the port will legitimately deliver, which for a 100 W USB PD port is about 5 A at 20 V, and the thermal check has to use the worst case direction. A port that is limited to 3 A in one direction and 5 A in the other is a specification written by the port controller, not by the eFuse.
The auto-retry behaviour on this string matters more than on a fixed input rail, because a port can be shorted by a user at any time. After the blanking interval the breaker opens, and the A member waits for the fixed delay and then tries again. If the short is still there, the cycle repeats, and the current during each attempt is limited by the set point rather than by the fault. That is a survivable pattern for a connector that sees abuse, while the L member would stay open until the port controller cycled the enable pin.
The overvoltage lockout is adjustable and responds in about one microsecond. In a USB PD system the voltage on the port can change in steps as the contract changes, so the lockout divider has to sit above the highest contracted voltage rather than above 5 V. A divider set for a 5 V port will trip every time the port negotiates 20 V, and the symptom is a port that works with a phone and fails with a laptop.
- The RCBCTRL function, because it is the only electrical difference against the 480 member and it cannot be added outside the part.
- The A or L suffix, since a user shorted port behaves very differently under the two.
- The lockout divider against the highest contracted voltage, not against 5 V.
- The current limit point against the largest legitimate delivery, in both directions.
- The thermal path through the 12 balls, because the reverse direction has the same dissipation.
- The level 1 moisture rating, which keeps the reel usable without a bake schedule.
Which projects this part fits
The vendor lists adapter and charger input protection, USB PD protection across phones, tablets, computers, notebooks, monitors and docks, server motherboards and add-on cards, enterprise storage, and power MUX and ORing. The reverse control pin points this member at dual role ports, on the go devices, power banks that charge and discharge through the same connector, and docks that pass power to a host while running from an adapter.
Questions that come up before a purchase order is released
What does RCBCTRL actually do?
It disables reverse current blocking so power can flow from output to input in steady state. The current limit, the overvoltage lockout and the thermal protection stay active in both directions.
Can I use this part where reverse flow is never wanted?
Yes, with the pin tied to the state that keeps blocking active. The pin has to be driven rather than left floating, so the board needs a defined level from the port controller or a resistor.
Does the A suffix change the reverse behaviour?
No. The A suffix sets the response to a fault, auto-retry in this case. The reverse behaviour is set by RCBCTRL.
What current should the limit be set to for a 100 W port?
Above the largest current the port will deliver, which is about 5 A at 20 V, with margin for the ten per cent accuracy above 3 A. The thermal check uses the same figure in both directions.
Why does the lockout divider matter so much on a PD port?
Because the port voltage changes with the contract. A divider set for 5 V trips at 20 V, and the fault looks like a port that only works with small devices.
How SUPERB handles this line
A part like this is usually bought against a port controller that was chosen first, so the work is in matching the pin function rather than the current rating. Our power management cross reference carries the family mapping, our incoming inspection plan covers the reel and marking check that catches a 480 reel sent in place of a 481, and our lead time solutions page covers what we do when one member of a family is on allocation and the others are not.