Contact Us

TPS25750DRJKR

Brand: Texas Instruments
Texas Instruments TPS25750DRJKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS25750DRJKR — Power Management & Signal Chain | Superb Automation

TPS25750DRJKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS25750DRJKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS25750DRJKR: USB Type-C and power delivery controller with integrated 28 V load switch

TPS25750DRJKR is a standalone USB-C power delivery controller in the 40 pin RJK body that integrates a 5 V 3 A source switch and a 28 V 7 A bidirectional load switch, negotiates power over the configuration channel without firmware, and holds 26 V tolerant CC pins in a QFN (RJK) body of 40 pins. The TPS25750 is a USB Type-C and power delivery controller aimed at power applications rather than at data. It integrates a 36 milliohm 5 V 3 A source switch and, in the D variant, a 16 milliohm 28 V 7 A bidirectional load switch, so the power path does not need external transistors. The controller is standalone: the power contract is set by configuration rather than by firmware, and an I2C port is provided for a companion battery charger.

Order code and package

Order codeTPS25750DRJKR
FunctionUSB Type-C and power delivery controller
Integrated source switch5 V, 3 A, 36 milliohm
Integrated bidirectional load switch28 V, 7 A, 16 milliohm, D variant
CC pin tolerance26 V
Configuration channel protectionreverse current, overvoltage, inrush limiting
Companion interfaceI2C for a TI battery charger
Firmware requirementstandalone configuration
Package40 pin QFN, RJK body
DocumentTPS25750 data sheet

Electrical parameters that decide the application

VBUS UVLO, rising3.6 V to 3.9 V
VBUS UVLO, falling3.5 V to 3.8 V
VBUS UVLO hysteresis0.1 V
VIN_3V3 power on threshold2.56 V to 2.76 V, 2.66 V typical
VIN_3V3 power off threshold2.44 V to 2.64 V
LDO_3V3 output3.0 V to 3.6 V, 3.4 V typical, up to 18 mA
LDO_1V5 output1.49 V to 1.65 V, 1.5 V typical
VIN_3V3 current in active source mode3 mA typical
VIN_3V3 current in active sink mode3 mA typical, 6 mA maximum
VIN_3V3 to LDO_3V3 resistance1.4 ohm at 50 mA

Points to check before this part goes on a BOM

The two integrated power paths are what separate this part from a controller that needs external transistors. The 36 milliohm source switch carries 3 A with a 108 mV drop and 0.32 W of loss, and the 16 milliohm load switch carries 7 A with a 112 mV drop and 0.78 W. Both are inside the package, so the board has one component where a discrete version would have two FETs, two gate drives and a current sense circuit.

The 28 V rating on the load switch is the number that survives a user plugging a 20 V supply into a port that expects 5 V. A USB-C port without protection sees that 20 V on its VBUS pin and, in the worst case, on the internal nodes behind it. The 26 V CC pin tolerance is the other half of the same story: the configuration channel is the first thing that touches an unknown cable, and a controller whose CC pins stop at 5.5 V is destroyed by a faulty charger before any negotiation begins.

Standalone operation means the power contract is set by configuration data rather than by a firmware loop. The practical consequence is that the product can be certified without a software development effort, and the less convenient consequence is that any change in the power behaviour is a configuration change that has to be regenerated and revalidated, not a line of code. That trade is the reason the part is popular in products where the USB behaviour is fixed and the team has no firmware engineer to spare.

The VBUS undervoltage lockout at 3.6 V to 3.9 V rising and 3.5 V to 3.8 V falling is the threshold at which the controller will consider the bus present. With 100 mV of hysteresis, a source that ramps slowly through that window can produce several transitions unless the rise time is controlled, which is why the specification of the source and the input capacitance are part of the same decision as the controller.

The internal LDOs produce 3.4 V and 1.5 V rails for the controller and for a small external load, with a 3.0 V to 3.6 V window on the 3.3 V rail and up to 18 mA available. That is enough for the controller and a companion circuit, and not enough for a radio or a display. The 1.4 ohm resistance from VIN_3V3 to LDO_3V3 at 50 mA is the reason the input to that LDO should be a stable rail rather than a bus that sags during a negotiation.

Current draw is 3 mA typical in both source and sink mode and 6 mA maximum in sink mode, which is small enough that a product can keep the controller alive from the bus while the rest of the board is off. That is what allows a docking station or a monitor to respond to a cable insertion without waking the main system, and it is the behaviour a user experiences as a port that works immediately.

The I2C port for a companion charger is the difference between a controller and a power system. Voltage and current negotiated over the configuration channel have to reach a charger that can actually deliver them, and the controller passes the contract on rather than trying to regulate the bus itself. A charger that is not on the supported list can still be used, but the negotiation then has to be handled outside the controller, which puts the firmware project back on the table.

Where this order code fits

This order code belongs on USB-C chargers, docking stations, portable power banks, monitors with USB-C input and industrial equipment that takes power over a USB-C connector. It is chosen when the product has to appear as a compliant source or sink without adding a microcontroller and a firmware project, and when the power path has to survive a non compliant cable or a user pushing 20 V into the wrong port. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the OEM Procurement page.

Questions buyers ask

Does this part need firmware? The power delivery behaviour is configured rather than programmed, so a product with a fixed power requirement does not need a firmware project. The configuration is generated from the vendor's tool and stored for the controller, and a change to the supported voltages or the current limit means regenerating that configuration. Products that need dynamic behaviour beyond the supported modes do need a host.

What protects the port from a faulty charger? The CC pins tolerate 26 V, the VBUS path has overvoltage and reverse current protection, and the source switch limits inrush. The combination covers the common failure of a non compliant source presenting a high voltage on VBUS. It does not cover a lightning surge on the cable, which is a board level protection question and belongs to a transient suppressor at the connector.

Can the load switch be used in both directions? The 16 milliohm 28 V switch in the D variant is bidirectional, so the same port can source power to a device and sink power from a charger. That is what makes a single port usable as both an input and an output. The S variant lacks that switch and is intended for source only products, which is why the two order codes are not interchangeable on one board.

How much power can the integrated switches carry? The source switch carries 5 V at 3 A, which is the 15 W contract, and the load switch carries up to 7 A at 28 V. Those are the switch ratings and they are not the same as the power the product is certified for: the cable, the connector and the charger all have their own limits, and the lowest one decides.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.