TPS2549RTER
Product Specifications
TPS2549RTER
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2549RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2549RTER USB charging port controller and 3 A power switch with cable compensation
The TPS2549 puts the two functions that a charging port needs into one body: the data line controller that presents the charging signature, and the power switch that carries the current. It adds a current sense output that can drive the feedback of an upstream converter, so a port with a long cable and a 5 V rail that sags under 3 A can be compensated at the source instead of at the connector.
The switch is a 47 milliohm high side FET rated at 3 A continuous, with two selectable current limits so a multi port system can drop to a lower limit when adjacent ports are drawing heavily. The data line side covers the shorted mode, divider 3 and 1.2 V mode, plus a client mode that keeps the data lines connected while the power switch is off so a host can update firmware on a device without fighting it for power.
Key parameters taken from the TPS2549RTER document
| Operating range | 4.5 V to 6.5 V on the input, which covers a 5 V rail with cable and connector drop above it |
| High side switch | 47 milliohm typical on resistance |
| Continuous current | 3 A maximum continuous output current |
| Current sense output | 5 per cent accuracy, which is the figure used for cable compensation at the upstream converter |
| DCP selection | Automatic across the shorted mode of BC1.2 and YD/T 1591-2009, divider 3 at 2.7 V and the 1.2 V mode |
| CDP support | Charging downstream port mode per the battery charging specification revision 1.2, which allows data and up to 1.5 A at the same time |
| Data line switch resistance | 2.9 ohm typical at 2.4 V of common mode and 4 ohm typical at 0 V, both with 30 mA of test current |
| Data line bandwidth | 925 MHz at the 3 dB point into a 50 ohm load, which is what keeps a high speed link usable through the switch |
| Isolation when off | 27 dB of off state isolation at 250 MHz and 23 dB of cross channel isolation at the same frequency |
| ESD | 8 kV contact and 15 kV air discharge per IEC 61000-4-2 on the data lines, without external parts |
| Protection | Short to VBUS protection on both data lines, which is the fault a damaged cable produces |
| Client mode | Data lines stay connected while the internal power switch is off, so a host can update a device without a power conflict |
| Thermal range | Minus 40 to plus 125 degrees junction |
| Package | WQFN of 3.00 mm by 3.00 mm, sixteen pins |
| Carrier | 3000 pieces on a large reel for the RTE string, with a 250 piece small reel row under the T suffix |
| Moisture | Level 1 at 260 degrees with an unlimited floor life |
| Part marking | 2549 on every published row |
| Status | Active and in production, with a G4 row of the same body on the same carrier |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The current sense output is the feature that changes what a system can promise. A 5 V rail that leaves the converter at 5.0 V arrives at the connector lower, and the drop grows with current and cable length. The sense output carries the port current with 5 per cent accuracy, and feeding it into the feedback node of the upstream converter raises the source voltage as the load rises, so the connector stays near 5 V instead of sagging to 4.6 V at 3 A.
The two current limits exist for multi port systems. A notebook with three ports and a 65 W adapter cannot give 3 A to all three at once, and the lower limit lets the system advertise less to the device that is plugged in second. The device reads the data line signature, so the change has to be made on the data lines as well as on the limit, and the controller handles that selection internally through the DCP automatic mode.
The 47 milliohm switch dissipates about 0.42 W at 3 A, which in a 3 mm by 3 mm body is a real thermal task. The exposed pad has to be soldered to a copper area, and the current rating is a junction temperature rating rather than a package rating. A product that runs 3 A continuously in a sealed enclosure should measure the pad temperature rather than trusting the 125 degree number.
The client mode is the least understood function. In a normal charging port the switch is on and the data lines carry the charging signature. In client mode the switch is off so the port does not source power, but the data lines remain connected, which lets a host update a device over USB while the device is powered from its own battery. Without that mode the host and the device both try to supply VBUS and one of them loses.
Short to VBUS on a data line is a common failure after a damaged cable, and it is the reason this part integrates the protection rather than leaving it to external parts. The 8 kV contact and 15 kV air rating applies to the data lines with no external diodes, which saves board area on a charger that has three or four ports in a small shell.
- The current limit setting against the adapter rating, since the 3 A figure is the switch rating and not a promise the supply can keep.
- The sense resistor or the sense output path, because the cable compensation loop depends on a clean current signal.
- The data line mode needed by the target market, since the shorted mode, divider 3 and 1.2 V answer different devices.
- The exposed pad copper, which decides whether 3 A can be continuous in the enclosure the product ships in.
- ESD protection at the connector, which the part covers on the data lines but not on VBUS.
- The reel size, because the RTE string ships at 3000 pieces and a prototype line may need the 250 piece row.
Which projects this part fits
This part fits notebook and docking station ports, wall adapters with one or two USB sockets, aftermarket vehicle chargers and hub boards where a port has to charge at 1.5 A or more while data is moving. It also fits equipment that has to update a connected device over USB without providing power to it, which is where the client mode earns its place.
Questions that come up before a purchase order is released
Does the switch carry the full 3 A all the time?
The 3 A is a maximum continuous output current for the switch. The sustained figure is set by the junction temperature in the enclosure, and the 47 milliohm on resistance at 3 A gives about 0.42 W to remove from a 3 mm by 3 mm body.
What is the cable compensation actually doing?
It raises the upstream converter output as the port current rises, using the current sense output. The port voltage at the connector stays closer to 5 V instead of falling with cable and connector resistance.
Can the port charge and transfer data at once?
Yes, in charging downstream port mode the data lines stay connected and the port can deliver up to 1.5 A while a data link is active.
What happens if a data line shorts to VBUS?
The part integrates short to VBUS protection on both data lines, which is the fault a crushed cable produces. The protection is internal and needs no external diodes.
Is the part automotive qualified?
The document is the industrial revision and the addendum rows carry no Q1 suffix, so the automotive reading of this string is not confirmed by the document. A vehicle charger that needs the qualification has to use a part with the Q1 suffix.
Why does the part have two current limits?
So a multi port system with an adapter that cannot feed every port at full current can advertise a lower limit on the port that is plugged in later, instead of collapsing the rail.
How SUPERB handles this line
Charging port controllers live or die on the data line details, and the winning habit is to check the exact member against the market the product ships to rather than against a headline. Our power management cross reference lists the parts this one is cross referenced against, our lead time planning service covers the lead time picture on the connector and passive side of the same port, and our incoming inspection plan is the inspection plan we apply to incoming USB controllers before they go on a line.