Contact Us

TPS2514DBVR

Brand: Texas Instruments
Texas Instruments TPS2514DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2514DBVR — Power Management & Signal Chain | Superb Automation

TPS2514DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2514DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2514DBVR: a single port USB charging controller in a six pin SOT-23 that puts the right voltages on the two data lines so a phone charges at its full rate from a charger that is not a computer

TPS2514DBVR is a data line controller that watches the voltages on D plus and D minus, recognises what has been plugged in, and applies the divider or shorted signature that the attached device expects before it will draw more than 500 mA in a SOT-23 body of 6 pins. The DBV body is six pins on a 2.90 mm by 1.60 mm pad, and the part exists because a charger that leaves the data lines floating gets 500 mA from a phone that would take 2 A.

Order code and package

Catalogue stringTPS2514DBVR, where 2514 is the single port member with two divider options and R is the large tape and reel
BodySOT-23, DBV, six pins, 2.90 mm by 1.60 mm, with two pins marked no connect that may be grounded or left floating
Reel3000 pieces on a large tape and reel, with a 250 piece small reel on the T suffix
Finish and moistureNIPDAU plating, level 1 at 260 C, which is unlimited floor life and no bake on the line
Temperatureminus 40 to 125 C junction
Marking2514 on the body, against PB3Q on the dual port members and 2513 on the earlier revision
DocumentSLVSBY8D, May 2013, revised June 2020
StatusActive and in production on the addendum dated July 2026

Electrical parameters that decide the application

Supply4.5 V to 5.5 V on the IN pin, with 7 V absolute maximum and a 0.1 uF ceramic capacitor required close to the pin
Supply current155 uA typical and 200 uA maximum, which is small enough to leave powered in a standby charger
Data pinsDP1 and DM1, 5.8 V absolute maximum, 10 mA of recommended continuous sink or source current and 35 mA absolute maximum
Divider oneone data line at 2.0 V and the other at 2.7 V, which is the signature most Android phones look for
Divider twothe same two voltages with the lines swapped, which the part selects on its own when a device expects the other polarity
Output impedance24 to 36 kOhm on the divider outputs and 80 to 130 kOhm on the pair that forms the second signature, which is what a phone measures to identify the charger
Shorted modeD plus shorted to D minus, both for the USB battery charging specification revision 1.2 and for the Chinese YD/T 1591-2009 standard
Automatic switchingthe part re-arranges the data line connections when a device is attached, so a charger built with it works with both divider polarities without a jumper
ESDplus or minus 2000 V human body model on the supply pin and plus or minus 6000 V on the data pins, with 500 V charged device model
Current paththe part does not switch the 5 V rail. A separate power switch or a protected source feeds VBUS to the connector

Which revision matches which phone

TPS2514DBVRsingle port, divider one and divider two, 3000 pieces on a large reel, marking 2514, this page
TPS2514ADBVRsingle port with divider three at 2.7 V and 2.7 V plus the 1.2 V mode, marking PB3Q, and the A is the only difference in the string
TPS2513DBVRthe dual port member, two connectors on one die, for a charger with two sockets
TPS2513ADBVRdual port with the A revision signatures, marking PB2Q
The catalogue family without the Athe plain 2513 and 2514 cover divider one and divider two; the A members add divider three and the 1.2 V mode
A discrete divider networktwo resistor pairs and a switch do the same job with four parts, no automatic polarity detection and a larger board area

Points to check before this part goes on a BOM

A charger that leaves the data lines alone is a 500 mA charger. The USB specification caps an unconfigured port at 500 mA, and a phone that sees nothing on the data lines is entitled to assume it is plugged into a computer and draw only that. The controller here applies a signature that the phone recognises as a dedicated charger, and the phone then draws whatever its own charger profile allows. On a 2 A phone, the difference between a floating data line and a correct divider is the difference between an eight hour charge and a two hour charge.

Two divider polarities exist because two generations of phones look for opposite arrangements. Divider one puts 2.0 V on one line and 2.7 V on the other, and divider two swaps them, and a charger that only offers one of them charges half the phones in a drawer at the slow rate. This part detects the polarity the attached device expects and connects the divider accordingly, which is why the two pins are marked as inputs and outputs at the same time. It is the feature that makes a single part usable in a universal charger.

The A revision adds a third signature and a fourth mode, and the difference is entirely inside the order code. The plain 2514 offers divider one, divider two and the shorted modes. The 2514A adds divider three, which puts 2.7 V on both lines, and the 1.2 V mode. A bill of materials that says 2514 and a purchase order that ships 2514A are electrically different at the two data pins, and a phone that needs divider three will not charge at full rate from the plain part. The marking on the body is the only way to tell them apart on a reel.

This part does not switch power and it does not protect the port. It sits on the data lines and the 5 V rail goes through a separate switch or a protected source, so a board that expects the 2514 to limit current or to survive a shorted cable is missing a part. The TPS2561A is the switch that usually accompanies it, and the pairing is common enough that the data sheet shows it in the simplified circuit. Reading only the first page of the data sheet leaves that out.

The supply current of 155 to 200 uA is the number a standby charger budget uses. A charger that is plugged in but idle still runs this part, and on a 5 V rail that is 1 mW. In a vehicle that sits for a month, that is 0.7 Wh, which is small against the battery and not small against a specification that asks for less than a milliamp of standby. A charger that must meet a 100 uA standby budget needs the whole port switched off when no device is attached, which this part does not do on its own.

The data pins are rated for 10 mA of continuous current and 35 mA absolute maximum, and a phone that misbehaves can pull more than the recommended figure while it probes the port. The 24 to 36 kOhm output impedance is what limits the current in normal operation, and it is also what a phone measures to identify the charger, so a substitution to a resistor network with a different tolerance changes both the current and the identification. That is why the impedance window is printed in the table rather than left to the typical value.

What a phone actually measures

A phone attaches a small current source to each data line and measures the voltage that results. With a 24 kOhm to 36 kOhm source impedance behind 2.0 V and 2.7 V, the measured voltages land in the window the phone is looking for, and the phone concludes it is attached to a dedicated charging port. With a floating line the measurement is undefined and the phone falls back to the 500 mA assumption.

The shorted mode is a different test. The phone pulls one line up and looks for the other line to follow, which only happens when the two are shorted together. That is the mode a phone uses to identify a charger that follows the Chinese standard, and it is why both shorted modes are offered on the same part as the dividers.

Port protection sits outside this part

The 5 V path to a USB connector has to survive a cable that is shorted, a device that draws more than the port allows and a connector that is inserted at an angle. None of that passes through the 2514, so the switch in front of the connector carries the current limit, the thermal protection and the fault flag. A charger built with the controller and without the switch is a charger with an unprotected port.

The data pins themselves are protected up to plus or minus 6000 V human body model, which is the level a connector on the outside of an enclosure needs. That protects the part and does not protect the phone, so the port still needs its own transient arrangement if the connector is exposed.

Where this order code fits

This is the charging port controller in a vehicle USB charger, a wall adapter with a USB socket, a power bank, a docking station or a monitor with a charging port, where a phone or a tablet has to see a dedicated charger signature before it will draw more than half an amp Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it limit the charging current? No. It only sets the data line signature. The 5 V path needs its own switch such as the TPS2561A, which carries the current limit and the protection.

What is the difference between the 2514 and the 2514A? The A adds a third divider at 2.7 V on both lines and a 1.2 V mode. The plain part covers divider one, divider two and the shorted modes.

Will it work with an iPhone? The shorted mode is what an Apple device looks for, and both the specification revision 1.2 short and the Chinese standard short are supported.

How much current does the part itself draw? 155 uA typical and 200 uA maximum from the 5 V rail, plus whatever the data lines source into the attached phone.

Can the data pins be left floating? No. Both are connected to the connector data lines. The two no connect pins may be grounded or left open, and they have no function.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.