Contact Us

TPS22920YZPR

Brand: Texas Instruments
Texas Instruments TPS22920YZPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22920YZPR — Power Management & Signal Chain | Superb Automation

TPS22920YZPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22920YZPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22920YZPR: 4 A load switch from 0.75 V to 3.6 V with a controlled turn-on in a 0.9 mm by 1.9 mm body

TPS22920YZPR is a single channel load switch with an integrated N-channel pass device, built to bring a rail up slowly so the inrush does not collapse the source in a CSP body of 8 pins. The TPS22920 switches a rail of 0.75 V to 3.6 V with an on resistance of 5.3 mOhm at 3.6 V and a maximum continuous current of 4 A. The pass device is an N-channel MOSFET with a controlled gate ramp, so the output rises over a defined interval rather than in a step, which is how the part keeps a battery or a small regulator from seeing an inrush spike. Quiescent current with the switch on is 68 uA at 3.6 V, shutdown current is 5.5 uA maximum, and the body is a 0.9 mm by 1.9 mm chip scale package with a 0.5 mm pitch.

Order code and package

Order codeTPS22920YZPR
Input voltage0.75 V to 3.6 V
Continuous current4 A maximum
On resistance at 3.6 V5.3 mOhm typical
On resistance at 1.8 V5.5 mOhm typical
On resistance at 0.75 V7.3 mOhm typical
Switch typeintegrated N-channel MOSFET, active high enable
Turn-oncontrolled ramp, 880 us rise time with a 10 Ohm load and 0.1 uF
Turn-off time3 us typical with the same load
Quiescent current68 uA typical at 3.6 V
Shutdown current5.5 uA maximum
Package8 pin chip scale, 0.9 mm by 1.9 mm, 0.5 mm pitch
DocumentTPS22920x data sheet

Electrical parameters that decide the application

Input leakage when off5.5 uA maximum with the output at zero
Pull-down resistance1250 Ohm to 1500 Ohm when disabled, at 3.3 V
On pin leakage0.1 uA maximum between 0.9 V and 3.6 V
On pin threshold1 V typical, from the switching characteristics
Reverse currentblocked while the switch is off
Rise time880 us at 3.6 V with a 10 Ohm load and a 0.1 uF capacitor
Fall time2 us at 3.6 V with the same load
Thermal paththe die pad of the chip scale body
Junction range-40 C to 85 C
ESD rating2 kV human body model
Logicactive high on the TPS22920, active low on the TPS22920L
Load capacitanceany value the inrush budget allows, the ramp sets the current

Points to check before this part goes on a BOM

On resistance of 5.3 mOhm at 3.6 V is the number that decides whether this part can carry 4 A. At 4 A the conduction loss is 85 mW, which the chip scale body can pass to the board through its pad, but at 0.75 V the resistance rises to 7.3 mOhm and the loss with it. A rail that runs at the bottom of the input range should be checked at the higher resistance rather than at the headline figure.

The controlled ramp is the reason to choose a load switch over a discrete MOSFET. With a 0.1 uF load the output rises in about 880 us, so a 10 uF load capacitance charges at roughly 40 mA rather than at the current the source can deliver. On a battery whose internal resistance is a few hundred milliohms, that difference is the difference between a clean start and a brownout of everything else on the rail.

The pull-down resistor is not a discharge circuit. At 1250 to 1500 Ohm it bleeds a 3.3 V rail down over a few tens of milliseconds with a small load, which is enough to stop a floating node but not enough to power down a board quickly. Where a fast decay is required, an active discharge has to be added, and the part is not that.

Reverse current blocking matters when a module can be powered from a second source. With the switch off, the body diode path is blocked, so a rail on the output side cannot feed back into the input. That is what allows this part to sit between a battery and a USB connector without a second diode and its drop.

Five and a half microamps of shutdown current is the price of the integrated control. On a board that ships with a battery installed, that current sets a shelf life: 5.5 uA is about 0.13 mAh per day, which over a year is 48 mAh. A product that has to sit on a shelf for two years needs a mechanical disconnect or a lower leakage part.

The two logic versions are easy to confuse on a BOM. The TPS22920 is active high and the TPS22920L is active low, and the bodies and the pin out are the same. A board that is populated with the wrong member will invert the enable, which shows up as a rail that comes on when the processor is held in reset rather than as an obvious failure.

At 4 A the part is close to the current where the package and the board trace both matter. The chip scale body has a 0.5 mm pitch and no room for wide traces under it, so the copper from the pad to the connector carries the full current and its temperature rise has to be included in the thermal budget rather than treated as a detail of the copper.

Where this order code fits

This order code belongs wherever a sub assembly has to be isolated from a battery or a main rail: portable equipment with removable modules, USB powered devices that must not back feed, and boards with several loads that are enabled in sequence. The 0.75 V floor means it can switch a modern core rail as well as a 3.3 V peripheral rail. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can this part carry 4 A continuously? It is rated at 4 A maximum continuous, and the on resistance at 3.6 V gives 85 mW of loss at that current, so the pad and the copper have to carry it away.

Does it block current from output to input? Yes, while the switch is off. The pass device is an N-channel MOSFET with the body path blocked in the disabled state.

What defines the turn-on current? The ramp and the load capacitance. With a 0.1 uF load the rise is about 880 us, and the inrush scales with the capacitance rather than with the source capability.

SUPERB supplies this order code with packing and date codes, and the Medical Device Components page covers the checks that keep a load switch from becoming the weak point in a power tree.