Contact Us

TMS470R1A288PGEQ

Brand: Texas Instruments
Texas Instruments TMS470R1A288PGEQ is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS470R1A288PGEQ — Power Management & Signal Chain | Superb Automation

TMS470R1A288PGEQ

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS470R1A288PGEQ from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS470R1A288PGEQ: 288K byte ARM7TDMI flash microcontroller in the 144 pin body, Q grade to 125 C

TMS470R1A288PGEQ is the 125 C version of the 288K byte device: two flash banks, 16K bytes of SRAM, two CAN controllers and the 42 pin expansion bus on a 144 pin LQFP in a LQFP body of 144 pins. The Q at the end of the code is the wide temperature grade defined in the family nomenclature: minus 40 to 125 C ambient, against minus 40 to 105 C for the T grade. The silicon and the pinout are the A288, with 288K bytes of flash in two banks of eight sectors, 16K bytes of SRAM, two SCC CAN controllers, three I2C modules, a twelve channel HET lite and the expansion bus that only the 144 pin body carries.

Order code and package

Order codeTMS470R1A288PGEQ
CoreARM7TDMI, 24 MHz, 48 MHz pipeline mode
PackageLQFP, 144 pins, body code PGE
Flash288K bytes, two banks, eight sectors each
SRAM16K bytes
CANtwo SCC controllers, 16 mailboxes each
High end timerHET lite, 12 high resolution channels
ADC10 bit, 12 channels
Expansion bus42 pins, 8 and 16 bit
Core supply1.8 V nominal
Temperatureminus 40 to 125 C, Q grade
DatasheetSPNS106B, revised August 2006

Electrical parameters that decide the application

Temperature gradeQ, minus 40 to 125 C
Junction limitminus 40 to 150 C
Flash endurance50 000 cycles at the rated temperature
Flash bankstwo, read while write across banks
General purpose I/O50 dedicated plus 43 shared
DMA16 channels, 32 control packets
I2Cthree multi master modules
Memory securityMSM readout protection
Watchdogsdigital and analog
Clock modulezero pin PLL with bypass mode
I/O supply3.3 V nominal
Package thermal144 pin LQFP, exposed pad on the board recommended

Points to check before this part goes on a BOM

The Q grade is twenty degrees above the T grade, and at 125 C ambient the junction is well above that. The 144 pin LQFP has a thermal resistance that has to be multiplied by the dissipation of the core, the I/O ring and the flash during an erase, and the answer decides whether the board needs a copper plane under the body or a heat spreader.

Flash erase at 125 C is the operation that heats the die most. Programming a 288K byte array while the ambient is at the top of the range puts the die into a state the steady state calculation never covers, so a field update should be scheduled for a cool moment or throttled, and the erase should never run in a loop while the cabinet is at temperature.

Two banks keep the update path open at 125 C as well. The bank that is not executing can be erased and verified while the application runs from the other, which means the network never drops and the die never spends long at the erase current. This is the practical argument for the A288 over the single bank A256 on a hot board.

The expansion bus is 42 pins of 3.3 V I/O, and at 125 C the memories on that bus have to be rated for the same range. An industrial 85 C SRAM on a 125 C board is the most common mistake in this part of the board, and it fails as intermittent reads long before it fails as a dead board.

The analog watchdog has an external RC network, and at 125 C the leakage on that node changes the timeout. The network values in the data sheet are calculated for the full range, so substituting a convenient resistor from the lab bin is not safe. The watchdog is a safety function on these boards and should be tested at temperature.

Two CAN controllers at 125 C are usually driving transceivers in the same hot enclosure. The controller is specified, the transceiver may not be, and the bus fault behaviour at the top of the range is where a gateway starts dropping frames. Check the whole chain, not just the processor.

Erase time is the number that decides whether a field update fits inside a service window. Two banks of eight sectors give the granularity to program one bank while the other runs, but the whole array still takes seconds to program, and at 125 C that is time the die spends at the erase current. A service procedure that assumes an instant update has to be rewritten before the board is released.

Where this order code fits

Under hood and transmission mounted controllers, engine bay sensor nodes, industrial equipment in sealed cabinets, and any board where the ambient inside the enclosure passes 105 C but the code base is already built around this device. Boards comparing it with a neighbouring part start from our Component Obsolescence Management page, and boards replacing a part that has gone end of life start from the MCU Cross Reference page.

Questions buyers ask

Is this the same silicon as the T grade? Yes. Same die, same package, same peripheral set; the Q grade widens the ambient range from minus 40 to 105 C to minus 40 to 125 C. The board still has to be checked for thermal and component ratings at the higher ambient.

Can a field update run at 125 C? It can, within the endurance rating, but the erase current heats the die further and the update should be throttled. The two bank arrangement lets the application keep running from one bank while the other is programmed, which shortens the time the network is at risk.

Does the Q grade change the maximum clock? No. The core runs at 24 MHz with the 48 MHz pipeline mode over the whole range. What changes is margin on flash access and on the PLL, which is why the wait states are set for the full range rather than trimmed at room temperature.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.