TMS320VC5509AZAYR
Product Specifications
TMS320VC5509AZAYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320VC5509AZAYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320VC5509AZAYR: Fixed point digital signal processor, 108, 144 and 200 MHz, with USB and three serial ports
TMS320VC5509AZAYR is a C55x fixed point DSP with on-chip RAM, a USB full speed port and an external memory interface for embedded signal processing in a BGA (ZAY) body of 179 pins. It runs a C55x core at 108, 144 or 200 MHz with two multiply accumulate units, carries 128K words of on-chip RAM and 64K bytes of ROM, and integrates a USB full speed slave port, three multichannel serial ports and a real time clock.
Order code and package
| Ordering string | TMS320VC5509AZAYR, 179-terminal MicroStar BGA, tape and reel |
| Core | TMS320C55x fixed point, dual MAC, 108, 144 and 200 MHz speed grades |
| Memory | 128K by 16 bit on-chip RAM, 64K bytes of one wait state ROM |
| External memory | 8M by 16 bit addressable space through the EMIF, SDRAM, SRAM and EPROM |
| Package note | The data manual lists 179-terminal BGA in GHH and ZHH codes and a 144-pin LQFP in PGE; the ZAY code is the lead free BGA body, and the package drawing should be confirmed against the orderable addendum |
| Supplies | 1.2 V core at 108 MHz, 1.35 V at 144 MHz, 1.6 V at 200 MHz, with 2.7 V to 3.6 V I/O |
Electrical parameters that decide the application
| Performance | Up to 400 million multiply accumulates per second at 200 MHz |
| Internal buses | One program bus, three data read buses and two data write buses |
| Serial ports | Three McBSPs, up to two MMC and SD interfaces |
| DMA | Six channel controller that runs independently of the CPU |
| USB | Full speed 12 Mbps slave port with bulk, interrupt and isochronous transfers |
| Converters and timers | 10-bit ADC, four channels in the BGA and two in the LQFP, two 20-bit timers, watchdog |
| Other | I2C master and slave, real time clock with its own supply domain, JTAG boundary scan |
Points to check before this part goes on a BOM
The speed grade is set by the core voltage, not by the order code alone. The same device runs at 108 MHz on a 1.2 V core, 144 MHz on 1.35 V and 200 MHz on 1.6 V, so a board that supplies 1.35 V and expects the 200 MHz timing has a timing closure problem rather than a bad part. The power supply and the speed selection are one decision.
The on-chip memory split matters for the loop. There are 64K bytes of dual access RAM in eight blocks of 4K words and 192K bytes of single access RAM in twenty four blocks, and the dual access blocks are the ones that can feed the two MAC units at full rate. A filter that keeps its coefficients and its sample buffer in single access memory will run well below the headline MAC rate, and the fix is placement rather than clock.
The 8M by 16 bit external space is addressed through an EMIF that handles SDRAM, SRAM and EPROM without glue. That is a large address space for a device of this class, and it is what allows a frame buffer or a look up table to live outside the chip. The catch is that every external access costs wait states, so the same algorithm that runs at 200 MHz from internal memory runs at a fraction of that when the data is external.
The USB port is a full speed slave, not a host. A product that needs to connect to a PC works, and a product that needs to read a USB stick does not, which is the single most common misunderstanding about this device. At 12 Mbps the port is also modest for audio or imaging, and the usual arrangement is USB for configuration and a serial port for the data stream.
The real time clock has its own clock domain and its own supply pin, so it can keep time while the core is off. A battery or a supercapacitor on that pin is the difference between a product that needs a time sync on every power up and one that keeps its log stamps. The RTC crystal is a separate component and its load capacitance has to match the crystal, which is the detail that turns a working prototype into a product with a drifting clock.
The package is a 179-terminal BGA on 0.8 mm pitch, which is a fine pitch body for a two layer board. It needs at least four layers with a via fan out pattern under the array, and the decoupling for the core has to sit on the underside directly below the ball field. A prototype built on a two layer board will run at 108 MHz and fail intermittently at 200 MHz, and the failure will look like a software bug in the DMA.
Where this order code fits
It is used in audio and voice processing, industrial measurement, medical instruments, motor control and portable signal processing products where a fixed point DSP with USB, serial ports and a real time clock replaces a microcontroller plus a separate codec interface. Teams comparing it with a neighbouring part start from our OEM Procurement page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Is the ZAY package the same as the GHH? Both are 179-terminal BGA bodies. The data manual lists GHH and the lead free ZHH, and the ZAY code is the lead free BGA ordering code, so the package drawing should be confirmed before a first build.
Can it run Linux? No. It is a fixed point DSP without a memory management unit, and the usual software stack is a real time kernel or a bare metal loop with the DSP BIOS style scheduling.
Does it need an external crystal? It needs a clock source on the input pin, and the real time clock needs its own 32.768 kHz crystal if the time has to be kept while the core is off.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.