TMS320LF2407APGES
Product Specifications
TMS320LF2407APGES
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320LF2407APGES from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320LF2407APGES: 144 pin DSP controller with the external memory interface, screened to 125 C
TMS320LF2407APGES is the 125 C version of the 2407A: 40 MHz C2xx core, sixteen PWM channels, a 16 channel 10 bit ADC and a full external memory bus on a 144 pin LQFP in a LQFP body of 144 pins. This is the same die and the same pinout as the A grade 2407A, with the S option fixing the ambient range at minus 40 to 125 C instead of minus 40 to 85 C. Everything the 144 pin body carries is present: 32K words of flash in four sectors, 2K words of single access RAM, 544 words of dual access RAM, sixteen PWM channels across two event managers, and the external bus with 64K words of program, data and I/O space.
Order code and package
| Order code | TMS320LF2407APGES |
| Core | TMS320C2xx fixed point DSP, 40 MHz |
| Package | LQFP, 144 pins, body code PGE |
| Flash | 32K words, four sectors, 4K, 12K, 12K, 4K |
| RAM | 2K words single access, 544 words dual access |
| PWM | 16 compare channels, two event managers |
| ADC | 10 bit, 16 inputs |
| Serial | CAN, SCI, SPI |
| External bus | 64K program, 64K data, 64K I/O, 16 bit data |
| Supply | 3.3 V, 3.0 to 3.6 V |
| Temperature | minus 40 to 125 C, S option |
| Datasheet | SPRS145L, revised September 2007 |
Electrical parameters that decide the application
| Instruction cycle | 25 ns, 40 MIPS at 40 MHz |
| Ambient range | minus 40 to 125 C, junction limited separately |
| Flash access | wait states programmable, timing specified over the full range |
| PLL | on chip, locks from an external crystal |
| ADC channels | 16, twin autosequencer, 500 ns minimum per conversion |
| Capture and encoder | six capture inputs, two encoder interfaces |
| Deadband | programmable, per event manager |
| Fault inputs | PDPINTA and PDPINTB, both drive the PWM pins high impedance |
| Digital I/O | 41 shared pins |
| Watchdog | on chip, independent clock |
| Code security | flash readout lock available |
| Package thermal | 144 pin LQFP, thermal pad on the board recommended |
Points to check before this part goes on a BOM
Eighty five to one hundred and twenty five degrees changes the board, not just the part number. At 125 C ambient the junction runs well above that, so the thermal path from the 144 pin body into the copper has to be planned, and the electrolytic capacitors around the processor have to be rated for the same temperature or they become the first failure.
The ADC reference is the second thing that moves. Offset and gain drift over the extended range are larger than at room temperature, so a current sense channel that was trimmed once at 25 C will read low at 110 C. Either trim at the working temperature or use a ratiometric arrangement where the same reference drives the sensor and the converter.
Flash timing at the top of the range is specified, not assumed. The data sheet gives the access time over the full temperature range, and the wait state count that works at 25 C is the one to use here as well; cutting wait states to gain speed is the classic way to make a hot board fail intermittently.
The external bus keeps its 3.3 V levels at 125 C, but the memories on it may not. Automotive temperature SRAM and flash are available, industrial 85 C parts are not acceptable on this bus, and the wait states have to be set for the slowest device on the bus over temperature rather than at room temperature.
The S grade carries the same 32K word flash map, so the loader in the first 4K sector and the application in the 12K sectors transfer unchanged from an A grade board. That is what makes a temperature upgrade a re-order rather than a firmware project, and it is the reason this code is still bought for existing drives.
Decoupling at 125 C is not optional. The 144 pin body needs a low inductance path on every supply pair, and the capacitors have to be close enough that the loop is short at 40 MHz. Boards that worked at 85 C with marginal decoupling fail here because the capacitance falls with temperature and the ESR rises.
Where this order code fits
Drives and power supplies that sit in a hot cabinet or next to the heat sink: downhole and submersible pump controllers, traction and elevator drives, compressor inverters, and outdoor telecom power plants where the ambient inside the enclosure passes 85 C in summer. Boards comparing it with a neighbouring part start from our Component Obsolescence Management page, and boards replacing a part that has gone end of life start from the MCU Cross Reference page.
Questions buyers ask
What is the difference between this and TMS320LF2407APGEA? Temperature grade only. Same die, same pinout, same flash map and the same peripherals; the A option is specified to 85 C and the S option to 125 C. The board still has to be rechecked for thermal and capacitor ratings when the grade goes up.
Does the 125 C grade change the maximum clock? No, the core still runs at 40 MHz with a 25 ns cycle. What changes is the margin: the flash access time and the PLL are specified over the wider range, so the wait states and the crystal tolerance have to be checked at the top of the range instead of at room temperature.
Can I use the external bus at 125 C? Yes, with memories rated for the same range. The processor side is specified, the bus is 3.3 V, and the wait states have to be set for the slowest device over temperature. An 85 C SRAM on a 125 C board is the usual mistake.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.