TMS320F28377SPTPT
Product Specifications
TMS320F28377SPTPT
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320F28377SPTPT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320F28377SPTPT: single core 200 MHz C2000 with 1MB flash in a 176-pin HLQFP
TMS320F28377SPTPT is a single core real time control microcontroller with an accelerator in a HLQFP body of 176 pins. It is the single core member of the 200 MHz generation: one C28x with its own control law accelerator, 1MB of flash and 164KB of RAM, in the 176-pin HLQFP with an exposed pad. The PTPT order code is that body in the T grade.
Order code and package
| Order code | TMS320F28377SPTPT |
| Package | 176-pin HLQFP, PTP body with exposed pad |
| Packing | tray |
| Core | one C28x at 200 MHz with a floating point unit |
| Accelerator | one control law accelerator at 200 MHz |
| Memory | 1MB of flash as 512K words, 164KB of RAM as 82K words |
| Grade | T, minus 40 to plus 105 degrees ambient |
Electrical parameters that decide the application
| ADC | four 16-bit converters at 1.1 MSPS each |
| PWM | ePWM channels with high resolution mode and trip zones |
| Serial | four SCI, two SPI, two I2C, three CAN |
| Other ports | USB, McBSP and a parallel interface |
| DMA | six channel controller |
| Supply | 3.3 V input and output with a 1.2 V core |
| Security | 128-bit code security over flash, RAM and OTP |
Family variants and how they differ
| F28377S | 1MB flash and 164KB RAM, single core, the part on this page |
| F28379S | 1MB flash with the configurable logic tiles |
| F28375S | 512KB flash and 132KB RAM, reduced memory |
| F28377D | the dual core version with 204KB of RAM |
Points to check before this part goes on a BOM
This is the part to choose when the product needs the 200 MHz core, the four converters and the 1MB of flash but not a second core. The RAM is 164KB against 204KB on the dual core device, and the missing 40KB is the message and shared regions that only exist when there are two cores to talk to each other.
The exposed pad on the HLQFP body is the thermal path for a device that can dissipate around a watt at full clock. It has to be soldered to a copper area with a via field under it, and the stencil has to leave enough paste to avoid voids. A board that treats the pad as mechanical support runs the part hotter than its own thermal calculation assumed.
Four 16-bit converters at 1.1 MSPS each give 4.4 MSPS of aggregate throughput when all four run, and each converter has its own sample and hold. That is four simultaneous channels rather than four sequential ones, which is the difference between measuring three phase currents at one instant and measuring them 900 ns apart.
The 176 pins are shared between the PWM outputs, the capture inputs, the serial ports and the parallel interface. A product with three motor phases, an encoder, two CAN buses and a USB port will find that some combinations cannot be brought out at once, and the pin multiplexing tables decide that before any drawing starts.
The T grade covers minus 40 to plus 105 degrees ambient. The same device number in the S grade covers 125 degrees and carries a different suffix. A cabinet that sits at 80 degrees internal ambient leaves 25 degrees of margin on the T grade, and the junction rise of the part at full clock has to fit inside that.
The core runs at 1.2 V from an internal regulator, and the 3.3 V rail feeds the input and output rings and the analogue subsystem. The reference for the converters is internal and its drift sets the measurement accuracy at temperature, so a product that needs absolute accuracy over the full range should bring in an external reference rather than rely on the internal one.
This generation is current, not legacy, and it is the one to specify for a new programme that needs more than the Piccolo parts can deliver. The development environment, the peripheral library and the reference boards are shared with the dual core device, so moving between them later is a software exercise rather than a restart.
Security is a single 128-bit module on this part. Once the password locations are programmed, an erased device can only be recovered with the password, so a contract programmer that loads the wrong image into a locked part destroys it. Products that ship locked should program the password after the functional test, not before.
The four converters give four simultaneous samples, so three phase currents plus a DC bus voltage can be measured at one instant with no skew. That is the reason a single core part at 200 MHz is enough for a three phase drive: the loop time goes to the computation, not to waiting for conversions in sequence.
The 176-pin body shares pins between the PWM outputs, the capture inputs, the serial ports and the parallel interface. A product with three motor phases, an encoder, two CAN buses and USB finds that some combination cannot be brought out at once, and the pin multiplexing table settles that before the board is routed.
The flash is 1MB as 512K words and it is large enough to hold a field bus stack, a motion library and a bootloader with room for a calibration table. The cost is the erase time: a full erase takes seconds, so a production fixture that erases before programming has to budget for it in the line cycle time.
The internal 1.2 V regulator needs its bypass capacitors close to the pins and the power up sequence in the data sheet. A board that copies a 3.3 V only supply tree from an earlier generation does not come up, and the failure is silent: no clock, no JTAG response, and a device that looks dead.
The flash is large enough to hold two images, which is how a field update is made safe: the new image is written to the spare bank, verified, and the boot pointer is moved. That scheme needs a bootloader that is never erased, and the linker command file has to reserve its sector from the start rather than after the product ships. Because the different device numbers in this generation share the peripheral library and the tool chain, a product can start on the 176-pin part and move to a dual core device later without discarding the application code, which is a useful hedge against a supply problem on one specific order code. The same library also means a firmware fix tested on one body is portable to the other, so a second device number can be qualified with a short regression rather than a full validation campaign.
Where this order code fits
It is used in high performance motor drives, grid tied inverters, battery test equipment and multi channel power supplies. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
How does it differ from the F28377D? One core instead of two, and 164KB of RAM instead of 204KB. The flash, the converters and the serial ports are the same generation.
Does it need a 1.2 V supply? The core voltage is generated internally from the 3.3 V rail, but the regulator pins still need their bypass capacitors and the power up sequence in the data sheet has to be followed.
What does the T grade cover? Minus 40 to plus 105 degrees ambient. The S grade of the same device number covers minus 40 to plus 125 degrees.
Can the flash be programmed in circuit? Yes, through the JTAG port or through one of the boot loaders in ROM. A production fixture normally uses JTAG with the security module unlocked until after test.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.