TMS320F28377SPTPS
Product Specifications
TMS320F28377SPTPS
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320F28377SPTPS from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320F28377SPTPS single core real time microcontroller with 1 MB of flash in a 176 pin package
The TMS320F28377SPTPS is the 176 pin member of the F2837xS family, a single core real time controller built on the C28x CPU at 200 MHz with a floating point unit, a trigonometric math unit and a control law accelerator that runs its own floating point code at the same clock. It carries 1 MB of flash with error correction and 164 KB of RAM, four 16 bit analog to digital converters, 24 pulse width modulation channels and a USB 2.0 port with the physical layer inside the package.
This is the part chosen when one core has to close several control loops at once and still talk to a host. Motor drives with three phases plus a power factor stage, grid tied inverters, servo amplifiers, high end power supplies and radar power conditioning are the usual homes. The suffix chain in the code is worth reading before ordering: PTP is the 176 pin thermally enhanced low profile quad flat pack, and the final S is the temperature grade from minus 40 to plus 125 C junction.
Key parameters taken from the TMS320F28377SPTPS document
| Core | C28x at 200 MHz with a single precision floating point unit, trigonometric math unit and VCU-II |
| Co processor | control law accelerator at 200 MHz, runs floating point code independently of the CPU |
| Flash | 1 MB, error correction code protected |
| RAM | 164 KB total, 36 KB of dedicated and local shared RAM plus 128 KB of global shared RAM |
| Analog | four 16 bit converters at 1.1 MSPS each, 4.4 MSPS system throughput, differential inputs, up to 12 external channels per converter |
| PWM | 24 channels with high resolution on both the A and B outputs of eight modules |
| Capture and position | six enhanced capture modules, three enhanced quadrature encoder modules |
| Serial | USB 2.0 with MAC and PHY, two CAN, three SPI at up to 50 MHz, four SCI, two I2C, two McBSP |
| Memory interface | two external memory interfaces, one 16 or 32 bit and one 16 bit, with ASRAM and SDRAM support |
| Other | universal parallel port, six channel DMA, 169 general purpose pins on the 337 ball body and 97 on the 176 pin body |
| Supply | 1.2 V core and 3.3 V input output |
| Order code facts | TMS320F28377SPTPS, HLQFP PTP 176 pins, tray of 40, MSL Level-3-260C-168HR, minus 40 to plus 125 C, Active |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The analog front end is where most of the value sits, and it is also where most first articles fail. Four converters running at 1.1 MSPS each give a system throughput of 4.4 MSPS, but only when the sample and hold windows are short enough and the input drive is strong enough. A 12 channel converter fed from a high impedance divider will not reach the stated throughput, and the post processing block that averages or thresholds conversions in hardware exists precisely to avoid spending CPU cycles on that. Configuring it is part of the bring up, not an optimisation for later.
The 176 pin body carries 97 general purpose pins while the 337 ball body carries 169. That gap is the single most common reason a program moves package after the netlist is drawn: a board that needs three encoder interfaces, two CAN buses, four serial ports and a parallel port runs out of pins on the 176 pin part before it runs out of anything else. Pin multiplexing has to be planned on a spreadsheet before the netlist is frozen, and the vendor signal description table lists every alternate function for each pin.
Clock and supply sequencing are simpler than on the dual core member but still need attention. The device runs from 1.2 V core and 3.3 V input output, has two internal 10 MHz oscillators and an on chip crystal oscillator, and includes a missing clock detection circuit that forces a safe state if the clock stops. The windowed watchdog is the one to enable in production firmware, because a plain watchdog can be fed by a runaway loop while a windowed one cannot.
The moisture sensitivity and the tray packing matter at the assembly stage rather than at the bench stage. Level 3 with a 168 hour floor life means a tray that is opened and left on a line for a week is out of the window, and the parts have to be baked before reflow. For a 176 pin quad flat pack with a thermal pad, the reflow profile also has to be checked at the pad, because a partial wetting on the pad shows up as a thermal problem months later and reads like a firmware fault.
The orderable suffix tells the whole story without opening the document: PTP for the 176 pin thermally enhanced low profile body, S for the minus 40 to plus 125 C junction grade. The same family in the same body is offered at minus 40 to plus 105 C with the T suffix, and a build that mixes the two grades on one board will pass bench test and fail a temperature soak.
- The control law accelerator runs independently, so a slow background loop cannot delay a fast current loop, which is the whole reason to pay for this class of part.
- Two external memory interfaces allow a board to keep a fast SRAM on one and a slower SDRAM on the other without sharing a bus.
- The USB port has the physical layer inside the package, so an isolated host link can be built without an external transceiver.
- Six capture modules and three encoder modules cover a three axis servo with a spare capture for a home switch, without using CPU pins for the same job.
- The 168 hour floor life is the practical limit on how long a tray can sit open, and it belongs in the assembly work instruction, not only in the component file.
Which projects this part fits
Three phase motor drives with a power factor front end, grid tied solar inverters, energy storage converters, servo and robotics amplifiers, electric vehicle charging modules, radar power supplies and high channel count industrial controllers are the natural applications. The part is also common in defence programmes that need a real time core with a genuine floating point unit and a long vendor support history. Our MCU cross reference lists the parts we hold against this family, and the incoming inspection plan page sets out what we check on a 176 pin tray before it goes to the line.
Questions that come up before a purchase order is released
Is this the dual core member of the family?
No. The S in the family name marks the single core member, with one C28x core and one control law accelerator. The dual core parts are the F2837xD family, which have the same pinout in this body but two C28x cores and a different flash and RAM split.
How much of the 1 MB flash is available to the application?
The whole array is ECC protected and code secure, and the boot ROM plus the security settings are separate. In practice the application has the full array minus the sectors reserved for calibration data, and the sector map in the document should be used to place the boot image and the parameter store rather than letting the linker decide.
What has to be checked on the first article?
The analog channels against a known source across temperature, the PWM dead band on a loaded phase, the watchdog window, and the reset behaviour when the clock is disturbed. The last one is the check that most often finds a configuration error, because the missing clock detector is enabled in the wrong order in many bring up scripts.
How SUPERB handles this line
We supply the TMS320F28377SPTPS in original trays with date code and lot traceability, and we can hold a small buffer for a program that is already in certification. If the board is close to running out of pins, send the peripheral list and we will confirm whether the 176 pin body or the 337 ball body is the right choice before the board is released. Start from the MCU cross reference page if the question is which family member is available on the shortest lead time.