TMS320F28377DZWTQR
Product Specifications
TMS320F28377DZWTQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320F28377DZWTQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320F28377DZWTQR: dual core 200 MHz C2000 in a 337-ball BGA, automotive grade reel
TMS320F28377DZWTQR is a dual core real time control microcontroller with two accelerators in a NFBGA body of 337 pins. It carries two 200 MHz C28x cores, each with its own control law accelerator, 1MB of flash shared between them and 204KB of RAM. The ZWTQR order code is the 337-ball BGA, the Q grade for automotive qualification and the R suffix for a large reel.
Order code and package
| Order code | TMS320F28377DZWTQR |
| Package | 337-ball nFBGA, ZWT body, 0.8 mm ball pitch |
| Packing | large tape and reel, R suffix |
| Cores | two C28x at 200 MHz with a floating point unit per core |
| Accelerators | two control law accelerators at 200 MHz |
| Memory | 1MB of flash as 512K words, 204KB of RAM as 102K words |
| Grade | Q, automotive qualified, minus 40 to plus 125 degrees ambient |
Electrical parameters that decide the application
| ADC | four 16-bit converters at 1.1 MSPS each, or 12-bit at 3.5 MSPS |
| PWM | 24 ePWM channels with 16 high resolution channels |
| Serial | four SCI, two SPI, two I2C, three CAN, two McBSP |
| Other ports | USB and a parallel interface, plus configurable logic tiles |
| DMA | two six channel controllers, one per core |
| Supply | 3.3 V input and output with a 1.2 V core |
| Security | dual code security module, one per core |
Family variants and how they differ
| F28377D | 1MB flash and 204KB RAM with two cores, the part on this page |
| F28379D | 1MB flash, 204KB RAM and four configurable logic tiles |
| F28376D | 512KB flash and 172KB RAM, reduced memory |
| F2837xS | single core members of the same peripheral generation |
Points to check before this part goes on a BOM
Two cores change the software model completely. Each core has its own flash bank, its own RAM, its own security module and its own interrupt controller, and the two communicate through message RAM and shared memory. A product that buys this part and runs one core only is paying for silicon it does not use, and the second core is not free to leave idle without a plan for its clock and its watchdog.
The flash is 1MB organised as 512K words, half of it per core, and 204KB of RAM split between dedicated, local shared, global shared and message regions. The split matters: a buffer placed in the wrong region costs arbitration cycles between the cores, and moving one array can change the loop timing of both.
The Q grade is AEC-Q100 qualified, which is a different statement from a wide temperature range. It covers qualification tests, a production part approval process and a change notification flow, and a product that sells into a vehicle needs the Q grade rather than a 125 degree industrial part with a similar number.
A 337-ball 0.8 mm BGA needs x-ray inspection and a controlled reflow profile. It also needs the board to be routed around the ball map rather than around a convenient pin order, because the power and ground balls are distributed to feed both cores. A repair bench that cannot reball a 337-ball device should plan for board replacement rather than rework.
The analogue subsystem on this generation is four independent 16-bit converters, each with its own sample and hold, giving simultaneous sampling across channels without the phase error of a multiplexed front end. That is what makes a dual axis servo drive possible on one device: each core can own its own converter and its own PWM set.
The on-chip 1.2 V core regulator has to be bypassed and sequenced correctly, and the data sheet's power up order is stricter than on the older single rail parts. A product that copies a 3.3 V only power tree from a Piccolo board will not bring this device up, and the failure looks like a dead part on the bench.
Configurable logic tiles are present on the F28379D and on some members of this family, and they let a product implement a small glue logic function without an external device. The tiles are not a FPGA: they are a fixed number of look up tables and flip flops, and the tool flow is part of the C2000 development environment rather than a separate place and route tool.
Automotive volume is what drives the lead time on the Q grade parts, and allocation follows the vehicle programme. A buyer with a non automotive product should expect to compete for the same line, and a product that can accept the S grade of a neighbouring device number has more sourcing options than one that is locked to a single order code.
The two cores communicate through message RAM with an interprocessor interrupt, and that protocol is written by the product team. The silicon provides the memory and the interrupt; it does not provide a queue, a handshake or an error path. Most field failures on dual core products are in that piece of firmware rather than in the control loop.
The 16-bit converters run at 1.1 MSPS each and the 12-bit mode at 3.5 MSPS, and the mode is a per converter setting. A product that mixes them gets the resolution it needs on the current channels and the rate it needs on the position feedback, which is how a servo drive keeps its loop time without a faster device.
Each core has its own security module, so a product can lock one core's code and leave the other open for field update. That is a useful arrangement for a product with third party motion libraries, and it is also a trap: a locked core with a bad image needs the password before it can be erased, on the production line.
A 337-ball BGA at 0.8 mm pitch is placed and reflowed, not reworked by hand. The assembly house needs a stencil with the correct aperture for the ball array, and the inspection step is x-ray. A product built in small volumes should count that cost before choosing the package.
The Q grade carries a change notification flow, so a silicon revision change reaches the customer before the parts do. That is part of what the qualification buys, and it is the reason a vehicle programme pays for the grade rather than using an industrial part at the same temperature. The dual core architecture is worth the complexity only when two loops genuinely have to run independently, and a product that uses one core for control and the other for communications should document the message protocol between them as part of the product definition rather than leave it to whoever writes the firmware.
Where this order code fits
It is used in automotive pumps and traction auxiliaries, multi axis servo drives, solar string inverters and high channel count power conversion. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
How much RAM does it have? 204KB in total, as 102K by 16 bit words, split across dedicated, local shared, global shared and message regions.
Can one core be left unused? It can, but its clock, watchdog and security module still need configuration, and the second flash bank stays allocated. Products that only need one core should look at the F2837xS members instead.
What does the R suffix add? Packing. R is a large tape and reel; the same device in a tray is a different order code.
Does the Q grade mean the same as 125 degrees? No. The Q grade adds AEC-Q100 qualification, a part approval process and change notification on top of the temperature range. A non automotive product can use the S grade of a sibling device number.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.