TMS320F28234PGFA
Product Specifications
TMS320F28234PGFA
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320F28234PGFA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320F28234PGFA fixed point C28x real time controller at 100 MHz in the 176 pin LQFP
The TMS320F28234PGFA is the 176 pin LQFP member of the F2823x line, a 32 bit real time controller that runs the C28x core at 100 MHz on a 1.8 V core with 3.3 V input and output. It carries 128K words of flash, which is 256 KB, split into eight 16K word sectors, plus 34K words of static RAM, 1K word of one time programmable memory and an 8K word boot ROM. Because the same die family also covers the floating point F2833x parts, a buyer comparing the two documents will see identical pinouts and identical converter blocks, and the real differences sit in the arithmetic unit, the clock ceiling and the size of the flash array.
The peripheral set is the one that made this family the default choice in motor drive and digital power work: six enhanced PWM modules with twelve outputs and six high resolution channels at 150 ps step, a 12 bit converter with sixteen channels and two sample and hold circuits at 80 ns conversion, a six channel DMA engine, a 16 or 32 bit external interface with more than two million words of reach, two CAN modules, three UARTs, one SPI port, one I2C bus and two buffered serial ports. The part is fixed point only, so anything written for the F28335 in single precision has to move to a software library or to scaled integer maths, which changes the cycle budget rather than the circuit.
Key parameters taken from the TMS320F28234PGFA document
| Core | TMS320C28x, 32 bit, fixed point, 100 MHz cycle of 10 ns, 1.8 V core and 3.3 V input output |
| Arithmetic | 16 by 16 and 32 by 32 multiply accumulate, dual 16 by 16 MAC, no floating point unit on this member |
| Flash | 128K by 16 words, 256 KB, eight sectors of 16K words |
| RAM and boot | 34K by 16 words of SARAM, 1K by 16 OTP, 8K by 16 boot ROM with SCI, SPI, CAN, I2C, McBSP, XINTF and parallel boot modes |
| Converter | 12 bit, 16 channels, two sample and hold, 80 ns conversion, internal or external reference |
| PWM | six ePWM modules, twelve outputs, six high resolution channels with 150 ps step resolution |
| DMA | six channel controller for ADC, McBSP, ePWM, XINTF and SARAM |
| External interface | XINTF, 16 or 32 bit data, more than 2M by 16 address reach |
| Serial | two CAN, three SCI, one SPI, one I2C, two McBSP |
| GPIO | 88 shared pins with input filtering, eight external core interrupts selectable on GPIO0 to GPIO63 |
| Security | 128 bit key and lock protecting flash, OTP and RAM blocks |
| Low power | IDLE, STANDBY and HALT modes, individual peripheral clock gating |
| Package | LQFP, PGF, 176 pins, the same pin assignment as the PTP body |
| Order code facts | TMS320F28234PGFA, A temperature grade minus 40 to plus 85 C, tray of 40, Active; the PGF block of the addendum prints Level-3-260C-168 HR |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The first decision is arithmetic, not pin count. A product that was written against the F28335 in single precision will compile for this part, but every float operation becomes a library call that costs tens of cycles. On a 20 kHz current loop with a handful of multiplications the difference is invisible, and on a control loop that carries a trigonometric transform or a filter cascade it can push the loop over its time budget. The quick test before committing a board is to build the existing firmware for the fixed point target and measure the worst case interrupt duration, not to estimate it from the clock ratio.
The flash array is half the size of the F28335 and it is cut into eight sectors of 16K words, so a bootloader plus two application images fills it faster than the headline 256 KB suggests. A parameter block that needs to survive a firmware update should not sit in a 16K word sector on its own, because one small record costs a whole sector, and the OTP region is a one way street. Read the map file at link time and keep at least one sector free for a recovery image, otherwise a failed update in the field has nowhere to fall back to.
The temperature letter in the order code is worth reading twice. The PGFA suffix is the A grade, printed at minus 40 to plus 85 C, while the S grade on the PTP body reaches plus 125 C. Because the document prints one pin assignment for both the PGF and the PTP body, a product that fails a thermal test can move to the wider grade without a board change, and that is often cheaper than adding airflow to an enclosure. What the A grade cannot do is run a cabinet at 70 C ambient with a 20 degree rise on the die, so the ambient inside the box, not the room, is the number to compare against 85.
Boot mode straps are set at reset and they are read from pins that also carry other functions. A stray pull up on a serial port pin during production programming can put the part into a boot mode the programmer does not expect, and the symptom looks like a dead board rather than a strap error. The document lists the boot selection table for SCI, SPI, CAN, I2C, McBSP, XINTF and parallel ports, and the safest production flow locks the strap with a resistor to the intended level before the first power up, then verifies the boot source in the test log rather than assuming it.
- Core rail measured at the device pin under full load, 1.8 V nominal, not at the regulator output.
- XCLKIN frequency and PLL lock time from a cold start, because a slow crystal shows up as an intermittent boot failure.
- Converter linearity at both ends of the range with the internal reference, then again with the external reference if the board fits one.
- Dead band and trip zone response on each PWM pair, measured on the gate driver input rather than at the device pin.
- Flash programming time for the whole array and the erase time per 16K word sector against the document limits.
- Die temperature at the worst case load inside the target enclosure, compared against the 85 C ceiling of the A grade.
Which projects this part fits
This part lands in the control card of a motor drive, the PFC and DC link stage of a telecom rectifier, a three phase UPS, a solar string inverter, a servo amplifier and a battery charger front end. All of those are applications where the loop rate is tens of kilohertz, the maths is scaling and filtering rather than floating point, and the bill of materials matters more than the last twenty five percent of core speed. It is also a common second source position for boards that were written for the F28335 and never used the floating point unit, because the pinout and the peripheral addresses are the same.
Questions that come up before a purchase order is released
Is this part a drop in replacement for the TMS320F28335?
The document prints one 176 pin assignment for the PGF and PTP bodies of both families, and the peripheral set matches, so the board can usually stay. The differences are inside: no floating point unit and a 100 MHz ceiling. Firmware that relies on hardware single precision has to be rebuilt and its interrupt timing measured again, and that timing check is the step that decides whether the swap is safe.
Does the PGFA ship on tape and reel?
The addendum prints this code as a 40 piece JEDEC tray, and the sibling rows of the same body are trays as well. There is no reel row for the PGF body in this document, so a line that needs reel feed should plan for a tray feeder or ask for the PTP body, which is printed with a tray of 40 too.
What separates the F28234 from the F28232?
Flash and RAM only. This member carries 128K words of flash and 34K words of SARAM, the F28232 carries 64K words of flash and 26K words of SARAM, and both run the same core at 100 MHz with the same converter and PWM count. A firmware image that already fits the smaller part will run on both.
Can this part be overclocked to 150 MHz like the F28335?
No. The document prints 100 MHz at 1.8 V for the F2823x members against 150 MHz at 1.9 V for the F2833x members, and the flash wait states and the converter timing are specified at those points. Running the part outside the printed point leaves every timing number in the document without a guarantee, including the 80 ns conversion time.
What finish and moisture class should the incoming inspection expect?
The addendum prints a NIPDAU finish and RoHS compliance for this body, and the PGF block shows Level-3-260C-168 HR. The carton label is the authority on the moisture class for a given lot, and a level 3 part has a 168 hour floor life after the bag is opened, so the reflow schedule has to be planned around that window rather than around the arrival date.
How SUPERB handles this line
We supply the TMS320F28234PGFA in original trays with date code and lot traceability, and we check the temperature letter and the moisture class on the label before the parts reach a line. If the product is in production and the question is continuity rather than a new build, send the annual volume and we will confirm the grade and hold a buffer. The MCU cross reference page is the place to start when the question is which member of the family can ship soonest, and the component obsolescence management page covers the case where the board has to keep running after the vendor moves the part to a legacy status.