TMS320C6746EZWT3
Product Specifications
TMS320C6746EZWT3
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320C6746EZWT3 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320C6746EZWT3: the 375 MHz grade in the ZWT package
The TMS320C6746EZWT3 is the same C674x fixed and floating point processor as the faster grade, ordered in the ZWT ball grid package at 375 MHz with a 1.2 V core and rated from 0 to 90 C. Level 1 holds 32 kilobytes of program cache and 32 kilobytes of data cache, and level 2 holds 256 kilobytes that can be split between cache and mapped memory.
The lower core voltage is the whole difference from the 456 MHz part. At 1.2 V the device runs 375 MHz, draws less current for the same work and produces less heat, and the board has to supply 1.2 V rather than 1.3 V. The two grades are not interchangeable on one board without a supply change, which is a decision that gets locked in when the regulator is chosen.
Peripherals are unchanged: two external memory interfaces, a universal parallel port, a multichannel audio serial port with sixteen serializers, USB 2.0 high speed with an integrated PHY, Ethernet MAC, three enhanced capture modules, enhanced PWM and a programmable real time unit subsystem.
Key data for the TMS320C6746EZWT3
| Core | C674x fixed and floating point, VLIW |
| Clock | 375 MHz at a 1.2 V core |
| Level 1 memory | 32 kilobytes program cache, 32 kilobytes data cache |
| Level 2 memory | 256 kilobytes, cache or mapped RAM |
| External memory | DDR2 and mobile DDR, plus NOR, NAND and SRAM on a second interface |
| Audio | Multichannel audio serial port with sixteen serializers |
| Networking | Ethernet MAC, IEEE 802.3 compliant |
| USB | USB 2.0 high speed with integrated PHY |
| Control | Three enhanced capture modules, enhanced PWM, eQEP |
| Package | 361 ball NFBGA, ZWT, 16.00 mm by 16.00 mm |
| Temperature | 0 to 90 C on the ZWT order code |
| Ordering | TMS320C6746EZWT3, tray, nickel palladium gold finish |
A 0 to 90 C rating is narrower than it looks
Zero degrees is a real limit. A product that is stored in an unheated warehouse in winter, shipped in an unpressurised hold, or installed in a plant room that drops below freezing will see the device outside its rated window before it is ever switched on. Storage and transport are separate specifications, but a board that is brought into a cold room and powered immediately is being asked to start outside the rating.
At the top of the window, 90 C is a case or ambient figure that has to be read from the data sheet with attention. A processor running a full signal chain dissipates most of its heat through the package and the balls, and the board copper under the package is the heat sink. A board with a ground plane under the device and vias through the pad runs much cooler than one with a signal layer underneath.
The practical answer for a product that has to work over a wider range is a different order code, not a bigger heat sink. Mixing grades on one board is possible only if the supply and the timing are built for the slower of the two.
What the lower clock costs in a filter chain
Going from 456 to 375 MHz removes about eighteen percent of the arithmetic budget. For a chain that was built with a comfortable margin, that is invisible. For a chain that was tuned to the edge, it shows up as a frame that overruns, and the usual fix is to move part of the work into the programmable real time units or to reduce the sample rate.
The programmable real time unit subsystem runs independently of the core and is well suited to bit level work: driving a serial bus, generating a precise pulse train, reading an encoder. Moving those jobs off the core buys back a few percent, and it also makes the timing independent of what the main loop is doing.
Memory bandwidth is often the real limit rather than instructions. A chain that streams samples through DDR2 at 375 MHz will spend more time waiting than one that keeps the working set in level 2, and the split between cache and mapped RAM then decides the outcome more than the clock does.
Where it fits in a build
Audio products, acoustic sensing, industrial drives and instruments that are used indoors. The 0 to 90 C window suits equipment inside a cabinet or a room, and the 361 ball package suits a board that already has the layer count for a fine pitch fanout.
For a programme that builds these boards over several years, the risk is the order code rather than the silicon. The component lead time solutions page sets out how we hold buffer against a forecast and what we check on a reel before it goes to the line, and the purchase order follow up page covers how a date is tracked once the order is placed.
The sourcing side of this part is covered on the NPI production launch checklist. For a board that carries a fine pitch processor and a DDR2 interface, that page covers what is checked before the first production run.
Questions we get on this code
Can the board run the 456 MHz part as well? Only if the supply can provide 1.3 V and the thermal path was sized for the higher dissipation. The pinout is the same, so the change is a supply and a re qualification rather than a board respin.
Does the device need a heat sink? At 375 MHz in still air, usually not, but a device running a continuous signal chain in a sealed box needs the case temperature measured rather than assumed. A small copper area under the package is cheaper than a heat sink and often enough.
How does it boot? From SPI flash, NAND or a host interface, selected by pins. Production boards normally boot from SPI, which keeps the host port free for test.
Is floating point worth it here? Yes, if the algorithm is written in float and the sample rate is moderate. At 375 MHz the single precision path still runs two multiply accumulates per cycle, which is more than most audio chains need.