Contact Us

TMP435ADGST

Brand: Texas Instruments
Texas Instruments TMP435ADGST is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP435ADGST — Power Management & Signal Chain | Superb Automation

TMP435ADGST

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP435ADGST from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP435ADGST: remote diode temperature sensor with beta compensation in MSOP-10

TMP435ADGST is a remote and local temperature sensor with automatic transistor beta correction in a MSOP body of 10 pins. It reads its own die temperature and the temperature of a diode connected transistor inside a processor, an FPGA or a discrete sensor, and it corrects for the beta of that transistor without a calibration step. The DGS order code is the 10-pin MSOP, and the T suffix on ADGST marks the reel.

Order code and package

Order codeTMP435ADGST
Package10-pin MSOP, DGS body
Packingtape and reel
Channelsone local channel and one remote diode channel
Interfacetwo wire SMBus, write byte, read byte, send and receive byte
Addressingpin programmable through two three state address pins
AlertsALERT and THERM2 outputs with programmable limits

Electrical parameters that decide the application

Supply2.7 V to 5.5 V
Local accuracyplus or minus 1.25 degrees typical, plus or minus 2.5 degrees maximum
Remote accuracyplus or minus 0.25 degrees typical, plus or minus 1 degree maximum at 0 to 100 degrees
Resolution12 bits on both channels
Conversion time12 ms to 17 ms on the local channel, 97 ms to 137 ms on the remote channel
Remote source current120, 60, 12 and 6 microampere settings
Beta correction range0.1 to 27, automatic on this order code
Ideality factor1.000 with beta correction, 1.008 with it disabled

Family variants and how they differ

TMP435automatic beta correction and series resistance cancellation
Beta correction offfor a diode connected transistor with base shorted to collector
Series resistance modecancels up to about 1 kohm of trace and package resistance
Address pinsthree state inputs give several bus addresses on one board

Points to check before this part goes on a BOM

The remote channel measures the change in base emitter voltage of a transistor at two forced currents. That measurement is independent of the absolute forward voltage, which is why a remote diode reads a processor die without calibration, and why the accuracy depends on the ideality factor of that particular transistor rather than on the sensor.

Beta correction matters for small geometry transistors where the base current is a significant part of the emitter current. Without it the part reads high by an amount that follows the transistor, which is a systematic error of several degrees on some processes. The automatic setting sweeps the current ratio and computes beta, so no register value has to be known in advance.

Series resistance cancellation removes the effect of the resistance between the sensor pins and the transistor. On a board this is the trace resistance plus the package and ESD structure of the processor, and a fraction of an ohm per degree is enough to matter: a 1 ohm series resistance in a 10 microampere measurement is 10 microvolts, which is about 0.5 degrees of error before cancellation.

The conversion time on the remote channel is 97 ms to 137 ms with beta correction on, against 36 ms to 52 ms with it off. A product that polls a processor temperature once a second can afford the slower mode; a protection loop that has to react in tens of milliseconds cannot, and it should either use the local channel or disable correction and accept the offset.

Two address pins give more than one sensor on a two wire bus without a multiplexer, which matters in a chassis that monitors several processors from one controller. The address pins are three state, so the third state is the unconnected case, and a board that leaves an address pin floating sits on whichever address that state selects rather than on a default.

The ALERT and THERM2 outputs are open drain and can be wired to a shared interrupt line. ALERT reports a limit violation and has a response address that lets the controller find out which sensor raised it, while THERM2 is a second threshold that usually drives a fan or a throttle. That shared line needs one pull up and a defined protocol, or two sensors asserting together become unreadable.

The local sensor reads the package, not the air. In a 10-pin MSOP the die is small and the leads are the main heat path, so a local reading on a board with a hot neighbouring regulator follows that regulator. Remote sensing exists exactly because the local channel cannot see the processor die, and the local channel is best used as a board level check.

Supply range of 2.7 V to 5.5 V covers both the 3.3 V and 5 V rails, and the SMBus pins are 5 V tolerant on a 3.3 V supply at the levels in the table: 2.1 V input high and 0.8 V input low with 500 mV of hysteresis. The hysteresis is what keeps a slow rising bus edge from producing multiple transitions on the clock line of a long backplane.

The ALERT output has a response address, so a controller can ask the bus which device raised the line. That works when the driver implements the protocol; a product that treats ALERT as a plain interrupt and reads every sensor in turn spends more bus time than the measurement itself. THERM2 is a separate threshold intended for a fan or a throttle, not for an interrupt.

The remote transistor is usually inside a processor and is specified by that processor's data sheet. The ideality factor of the sensor and the factor the part assumes have to agree, and the automatic setting on this order code measures beta rather than assuming it. A discrete transistor used as a remote sensor needs its collector and base connection chosen to match the mode in the configuration register.

The DXP and DXN pair carries a switched current, so it is a signal pair and not a supply. Routing it beside a switching node injects a differential error that the series resistance cancellation does not remove, and twisting the pair with a ground return is the usual fix on a cable. On a board the pair should be short, matched and away from the inductor.

The sensor draws a few hundred microampere during a conversion and much less between conversions, so the average current depends on the rate. A product that converts once a second sees the lower figure, and one that converts continuously sees the higher one. That matters in a handheld product where the sensor is one of a dozen loads on a small battery.

Where this order code fits

It is used in servers, projectors, telecom shelves and industrial controllers that need the die temperature of a processor without a diode pin on the sensor itself. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Does the remote channel need calibration? No calibration step is needed for the remote channel because beta correction and series resistance cancellation are automatic on this order code. The ideality factor of the transistor still has to be within the range the part supports.

Can it monitor two processors? Not on one part: there is one remote channel and one local channel. Two processors need two sensors on different bus addresses or an external multiplexer.

What limits the remote cable length? Series resistance and noise pickup. The part cancels about 1 kohm, so a long thin pair adds error once the loop resistance passes that, and the capacitance of a long cable slows the switched current settling.

Is the local channel accurate enough for a product limit? It is a plus or minus 1.25 degree typical part over the industrial range, which suits thermal management and not a calibrated measurement. Use the remote channel for the tight figure.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.