Contact Us

TMP432ADGSR

Brand: Texas Instruments
Texas Instruments TMP432ADGSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP432ADGSR — Power Management & Signal Chain | Superb Automation

TMP432ADGSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP432ADGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP432ADGSR: two remote diodes in a ten pin VSSOP

TMP432ADGSR is the two remote channel member of the TMP43x family. It measures two diode connected transistors and its own die, reports all three over SMBus, and keeps the beta compensation and series resistance cancellation of the single channel part. The extra channel costs two pins, which is why the body is the 10-pin VSSOP rather than the 8-pin used by the TMP431.

The string fits a board with two hot devices that are close enough to share one bus segment but far enough apart that one sensor cannot see both. A dual processor board, a board with a processor and an FPGA, and a power stage with two switching devices are the usual cases. One package, one address, three readings.

The values below come from SBOS441I, revised October 2019, and from the package option addendum. The electrical limits are shared with the single channel part; what changes is the channel count, the pin functions, the address strapping and the thermal resistance of the larger body.

Pin functions on the ten pin body

The 10-pin VSSOP adds DXP2 and DXN2 for the second remote channel, and it adds a second address pin, so the part can sit at one of four addresses on a segment. The ALERT and THERM2 outputs are still separate pins, and the supply, ground, clock and data pins keep their positions relative to the 8-pin part, which is convenient when a board is derived from a single channel build.

Two remote channels plus four addresses means eight remote diodes can be watched from four packages on one bus, with four local readings as a bonus. That is more thermal coverage than most boards need, and it is the reason the family covers the range from one channel to three rather than pushing to more channels per package.

The channel that is not used can be disabled in the configuration register, which stops it from converting and stops it from reporting a fault. On a board that is built in two variants, one with two processors and one with a single processor, the same part and the same firmware image can serve both if the unused channel is masked at start-up.

Channelsone local, two remote diode
Remote accuracy0.25 degrees typical, 1 degree maximum from 0 to 100 degrees
Local accuracy1.25 degrees typical, 2.5 degrees maximum
Resolution12 bits, 0.0625 degrees per count
Remote conversion with beta126 milliseconds typical, 137 maximum, with the recommended filter
Remote conversion without beta93 milliseconds typical, 100 maximum, with the filter
Local conversion15 milliseconds typical, 17 maximum
Beta compensation range0.1 to 27, automatic
Series resistance cancelled300 ohms with beta on, 1 k with beta off
Addressesfour, strapped by two address pins
Supply range2.7 V to 5.5 V
Quiescent current35 microamps at the slowest rate, 0.7 mA at eight conversions per second
Shutdown current3 microamps typical, 10 maximum
OutputsALERT and THERM2, open drain, 6 mA sink at 0.4 V
PackageVSSOP-10, DGS, 3.00 mm by 3.00 mm
Thermal resistance164.6 degrees per watt junction to ambient
Carrier2500 pieces on a large reel, marking DSDI
Moisture levellevel 2 at 260 degrees, one year floor life

Two channels, one current source

The two remote channels share the current source and the ADC, so they are measured in turn rather than at the same instant. That matters when the two diodes are on the same die: a fast thermal transient will be seen by one channel slightly before the other, and a host that compares the two readings during a transient will see a difference that is an artefact of the sampling order rather than a real gradient.

In steady state the difference is real and useful. A dual processor board with a shared heatsink shows the two die temperatures converging when the thermal path is good and diverging when a thermal pad has lifted or a fan has failed on one side. That comparison needs no additional sensor and no model, which is why the two channel part is common on server boards.

Series resistance cancellation applies to both channels independently, and the beta range is set per channel in the configuration register. A board can therefore run one channel against a discrete transistor with beta above 27 and the other against a substrate PNP with beta near 3, which happens on mixed boards where an older power device sits next to a modern processor.

Conversion time and the sampling budget

At the fastest rate the part spends most of its time converting: 15 milliseconds for the local channel plus 126 milliseconds for each remote channel with beta correction on, which is 267 milliseconds of conversion in a 125 millisecond window. The part therefore cannot hold eight complete conversions per second with all three channels enabled and beta correction on; the rate register sets the interval between local conversions and the remote channels are interleaved into that interval.

That is not a defect, it is a scheduling fact worth knowing. A host that needs a fast update on one channel should disable beta correction on that channel, or use a part with fewer channels, or accept the slower rate. A host that samples once a second has plenty of margin and can leave every channel enabled.

The local channel is the fastest and the least useful for protection, so a common arrangement is to convert it every cycle for ambient and fan health while the two remote channels alternate. The min and max registers then hold the peak values without the host having to poll at the conversion rate.

Thermal resistance of the larger body

The 10-pin VSSOP is 164.6 degrees per watt junction to ambient, slightly better than the 8-pin body at 168.2 because the lead frame is larger. At 0.7 milliamps and 5.5 V the dissipation is 3.85 milliwatts, which lifts the die 0.63 degrees above the board. That is small but not zero, and on a board that measures ambient with the local channel it is worth subtracting if the reading matters.

The larger body also gives more room for the two diode pairs to be routed apart. The document's recommended circuit keeps each pair as a tight differential route with its own filter, and the 10-pin body makes that easier than the 8-pin because the pins are not adjacent across two channels.

Where the two channel part is used

The document lists the same applications as the single channel part, with the addition of boards that carry two processors. In our builds the string appears in telecom line cards, in dual FPGA instruments and in power amplifiers that carry two transistor dice on one flange.

For an RF power amplifier the two channels can watch the driver and the final device, which is exactly the pair that fails together. A rise in the driver temperature without a rise in the final device is the signature of a drive level problem rather than a load problem, and that inference is available from two registers. Our RF component sourcing page lists the parts we hold for that class of build.

For a medical instrument the two channels cover the processor and the analog front end, where the second reading is used to correct a gain drift rather than to protect a device. That use needs the 0.25 degree typical accuracy rather than the maximum limit, and it needs the reading to be stable over time, which the 12-bit resolution provides. The medical device component sourcing page covers the parts we keep for that class of build, and the component traceability report covers the lot records.

Three questions buyers ask about this string

Is it a drop in replacement for the TMP431? Same family, different body and two more pins, so no. A board laid out for the 8-pin part needs a new land pattern for this one.

Can the second channel be left unconnected? It can, but the fault detector will report it. Disable the channel in the configuration register so the fault is masked and the conversion time is not wasted.

Does the A grade differ from the B grade in accuracy? No. The two grades share the electrical table; the difference is the marking and the lot history, as with the three channel part.